huntER_HuntED Posted August 1, 2011 Report Share Posted August 1, 2011 Finished a cheapmans '119, pretty happy. One may notice the notch in the pistol grip, I've got a new one on the way!!! Quote Link to post Share on other sites
PianoBlack Posted August 2, 2011 Report Share Posted August 2, 2011 Nothing special, just the VFC SR-635 that I've been planning on getting for months. -Piano Quote Link to post Share on other sites
SteevoLS Posted August 2, 2011 Report Share Posted August 2, 2011 How is it? I've been wanting to get one since they were released. Quote Link to post Share on other sites
Ivan le Fou Posted August 3, 2011 Report Share Posted August 3, 2011 Same question as SteevoLS. I had it in my hands in a shop once. Very small, but not too small, not so heavy (even had the feeling t was lighter than a KAC PDW). Quote Link to post Share on other sites
PianoBlack Posted August 3, 2011 Report Share Posted August 3, 2011 These are just my initial impressions, but I hope they prove useful: Overall build quality is excellent. I haven't found any loose fasteners and there is a minimal amount of wobble between the upper and lower receiver assemblies. The receiver pins are both the captive type, so no screws. There is a little play between LMT stock and the stock tube, but that is also to be expected. All three QD points are compatible with Daniel Defense and Midway Industries sling swivels (there's one on either side of the lower receiver and at the front of the hand stop). The battery for the LMT stock has yet to arrive so I can't describe its balance and weight accurately, but using a DD sling swivel mount as a hanging point, the center of gravity is at the T7 position (stock fully retracted). The gun is exceedingly light compared to the rest of the rifles I own at 5lb 3.3oz. I'm 6'2" with a lanky build and I find it to be very pointable, with the stock extended out the its 3rd position. The included high capacity magazine is lighter than both my G&P medium capacity and TM standard magazines. Also, the magwell fit is pretty snug with the VFC and G&P magazine, with neither being able to drop free. The TM magazine dropped free regardless which release was used. All controls (bolt release, selector switch, and magazine release) are ambidextrous and functional. The selector switch locks positively into position, though there is a little play between right and left selectors. My only complaint is the use of a 600m rear sight. KAC's product literature show the SR-635 with a 300m rear sight, which makes sense for the range that the weapon was designed for. I have a spare KAC 300m-type rear sight that I will swap in. Feel free to ask any more questions if you have them. I plan on subjecting the SR-635 to the "Afghanistan and back" treatment. -Vic Quote Link to post Share on other sites
The Vainguard Posted August 3, 2011 Report Share Posted August 3, 2011 Quote Link to post Share on other sites
FHairsoft1 Posted August 3, 2011 Report Share Posted August 3, 2011 Very nice work! i like that! What brand reddot is that? Quote Link to post Share on other sites
The Vainguard Posted August 3, 2011 Report Share Posted August 3, 2011 I opted to use a Primary Arms for now 1 Quote Link to post Share on other sites
beta08 Posted August 5, 2011 Report Share Posted August 5, 2011 Here are mine as of now; all G&P: M4 and CQBR: Mk18 Mod1: Apologies for the crappy pics in advance. Also, here is my Chinese 553 that I painted to look like a real one. I'm quite proud of it: It was originally almost all "gold". I had to paint the battery hood tan and the "inside" (?) black. 1 Quote Link to post Share on other sites
Leon Kennedy Posted August 5, 2011 Report Share Posted August 5, 2011 Just 'cuz, Quote Link to post Share on other sites
jdizzle921 Posted August 6, 2011 Report Share Posted August 6, 2011 Quote Link to post Share on other sites
spetsnazdave87 Posted August 6, 2011 Report Share Posted August 6, 2011 Well, swift on the heels of that lovely rifle, comes my cobbled together POS 'Dusty' carbine... Based on the MOH: Tier one cover art. 1 Quote Link to post Share on other sites
Leon Kennedy Posted August 6, 2011 Report Share Posted August 6, 2011 Well, swift on the heels of that lovely rifle, comes my cobbled together POS 'Dusty' carbine...Based on the MOH: Tier one cover art. Love it. Awesome cover art and awesome blaster. Quote Link to post Share on other sites
Dodger1911 Posted August 6, 2011 Report Share Posted August 6, 2011 I have a question for all of you m4 modifiers. I cracked the metal body on my classic army CQB R and need to replace it. I was looking at a G&P body because, as I understand it, they are very good. Am I going to have problems getting ther RIS onto the G&P Body? Quote Link to post Share on other sites
mimesis Posted August 6, 2011 Report Share Posted August 6, 2011 (edited) It depends on what kind of RIS it is. I'm not familiar with your particular model. If it is a one-piece, and especially if it uses a proprietary barrel nut, they you would definitely have problems. But I'm guessing that this is a two-piece, and that it may well use the standard delta-ring-style nut. G&P receiver threads are different, so at the very least you would need a G&P barrel nut--cheap enough. I'm also assuming that the rails fit into a "real-steel"-style delta ring (rather than the different airsoft style used in older TMs and JGs and ICSs, among others). Edited August 6, 2011 by mimesis Quote Link to post Share on other sites
Jimmypie Posted August 6, 2011 Report Share Posted August 6, 2011 is the CA cqbr RIS not just a drop in KAC replica? i think all youll need is the G&P delta ring assembly to fit your G&P receiver, although the only problem i can see is the the CA RIS will sit lower or higher than the G&P receiver RIS, as G&P is closer to Real Steel specs than CA. Quote Link to post Share on other sites
TheFull9 Posted August 7, 2011 Report Share Posted August 7, 2011 (edited) Bear in mind however, I've purchased a couple of after-market G&P branded delta ring assemblies in the past (i.e. including the barrel nut) and the nuts themselves have always been normal TM spec, so I'm not sure how you'd go about actually getting hold of a nut that'll fit the G&P upper receiver threads. E-mail G&P direcetly perhaps? Not sure how they are for responding directly to consumers. Edited August 7, 2011 by CKinnerley Quote Link to post Share on other sites
mimesis Posted August 7, 2011 Report Share Posted August 7, 2011 I've purchased a couple of after-market G&P branded delta ring assemblies in the past (i.e. including the barrel nut) and the nuts themselves have always been normal TM spec. That's odd. By TM spec you mean the metric thread size, right?, not the older non-real-steel-style delta assembly that TM used to use. I bought a G&P delta ring set (nut, spring, delta) off eHobbyAsia and the nut was definitely imperial. Quote Link to post Share on other sites
spetsnazdave87 Posted August 7, 2011 Report Share Posted August 7, 2011 Love it. Awesome cover art and awesome blaster. Cheers mate So much bashing went into getting this gun sorted out, it arrived with the front end hanging practically off. need to fix up the motor plate connectors and I should be sorted Quote Link to post Share on other sites
TheFull9 Posted August 7, 2011 Report Share Posted August 7, 2011 That's odd. By TM spec you mean the metric thread size, right?, not the older non-real-steel-style delta assembly that TM used to use. I bought a G&P delta ring set (nut, spring, delta) off eHobbyAsia and the nut was definitely imperial. Yeah I'm not sure how to explain it to be honest. Not to teach any egg sucking, but here's the exact product I've purchased a couple of times before: http://www.wgcshop.com/wgc2008/main/product_detail1.php?search_From=searchItem&item=GP-PT-DRS&search=special&rs=delta&catid=&cat= I've bought these from WGC and eHobby before, possibly 1-2 other retailers as well. I've used them on multiple TM SOPMOD series EBBs, G&P WOCs, an AGM GBB M4, the 'Action' AK to M4 front adapter kit and my 6 year old Classic Army 'M15'. I've also tested/fitted a few different things on to those guns themselves, including an Element 12" Novekse rail and another King Arms barrel nut. Quote Link to post Share on other sites
mimesis Posted August 7, 2011 Report Share Posted August 7, 2011 Because the imperial thread is slightly bigger diameter, I believe it will fit on to quite a number of receiver threads. The real problem is the other way round, when you go to fit a metric barrel nut on to a G&P receiver. Quote Link to post Share on other sites
Dodger1911 Posted August 7, 2011 Report Share Posted August 7, 2011 My RIS is the standard CA rail that came with the M15A4 CQB. So it sounds like the worst case scenario is I just need to pick up a delta ring if it's off sized. Not bad. Thanks all for the feedback! Quote Link to post Share on other sites
Extraordinaire Posted August 7, 2011 Report Share Posted August 7, 2011 (edited) Installed a Magpul MIAD. -Ex Edited August 7, 2011 by Extraordinaire 1 Quote Link to post Share on other sites
point7 Posted August 7, 2011 Report Share Posted August 7, 2011 here is my custom m4 that i build. 1 Quote Link to post Share on other sites
TheFull9 Posted August 7, 2011 Report Share Posted August 7, 2011 That is sexy. G&P with Dytac upper? Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.