Jump to content

curlyboy

Regular Poster
  • Content Count

    328
  • Joined

  • Last visited

Everything posted by curlyboy

  1. The TM fits in the Blackhawk Serpa for M&P perfectly and all my Glock holsters except the leather one so there must only be a small difference? Curlyboy
  2. That looks awesome just got my TM Glock 22 tempted to Gen 4. Can you swap the TM guts into a WE as the slide says Gen 4? Curlyboy
  3. Thanks guys I have gone for the bottom one, I was going either black or tan alias but thought I would mix them up a bit. Curlyboy
  4. Top or bottom which looks better (if any?) Curlyboy
  5. Airsoft zone has them, think I will stick to my 17 though. http://airsoftzone.co.uk/tokyo-marui/g34-pistol-gbb-tokyo-marui?limit=100 Curlyboy
  6. I also have the Serpa CQC holster for the M&P as well and that fits lovely with nothing to mark it. It is down to personal preference on holsters but the Serpa is very secure and for me that's what I want. Curlyboy
  7. I hair dryer modded my Glock 17 Serpa to take a TM Glock and as a bonus the M&P fits perfectly and there is no wear on the slide to speak of yet but in a year or so not sure will report if it does. Curlyboy
  8. See the link below granted the pictures look photo shopped but they have no trades same with the ones at fire support that also say no trades. Just seems odd that all the other TM range is traded but these are not, not sure if it is the whole umarex trades ball of wax thing again as the HK45 seemed un effected though it is not in stock in most places and fire support no longer lists it?? http://airsoftzone.co.uk/tokyo-marui/usg-compact-pistol-gbb-tokyo-marui?page=2&limit=100 Curlyboy
  9. Does anyone know of a UK supplier that has traded USPc as everywhere seem to only sell un traded ones?? Seems strange as trades on all other TM guns are normal. Curlyboy
  10. I always run the mags 1 round down, the nozzle is fine it seems like a cycling issue I don't know, I have 4 other mags and they fire perfectly it is just this one mag, I have cleaned the spring follower and the lips are fine and the pins are all in but it is frustrating there is no solution I can see!! Curlyboy
  11. Has anyone else had problems with mags? I wrote a few pages back about one mag not cycling leaving a round stuck under the nozzle I have 5 mags and this only happens with 1 mag? I have compared the mag with the others and they are the same which leaves me with almost a duff mag! Anyone have any ideas as I cleaned it and lubed it as suggested before but it is a mystery? Curlyboy
  12. From the left HK3P gen 4 glock 17, TM gen 3 glock 17 & KSC gen 3 glock 17, yes I have too many 17's maybe. Curlyboy
  13. Note that fire support in the UK finally has some but they are un trademarked? I thought all TM pistols had trades or is this another someone has the trades rights and does not want to be sued? Disappointing though maybe other suppliers will get traded ones in? Curlyboy
  14. WE Glock 17 Gen 4 & KSC Glock 17 Gen 3 Gen 4 Curlyboy
  15. I am now conflicted I have a KSC USP compact that is getting on (pre system 7) and I love TM pistols but is it worth getting this?? Nice review how is the trigger pull as the KSC is always a bit spongy? Curlyboy
  16. That's odd it fits fine in my glock 17 SERPA the only tight bit is on the left side of the slide above the rail might need a little rub with some modellers sand paper. Curlyboy
  17. A quick question has anyone had issues with BBs getting stuck in the hammer mech? I took the gun yesterday and it was cold but the mags were warm I had three mags the first mag fed fine and emptied, the second mag however fired a couple rounds the the slide jammed I took the mag out took off the slide and there is a BB in the hammer mech I cleared it put the same mag in fired one shot fine then again a BB gets stuck in the mech!! On clearing it again the mag emptied as normal and so did the third mag with no issues at all, granted the temperature is borderline but it seemed odd that the cy
  18. The gun fits lovely in a Glock 17 serpa as well, thanks for mag info as they don't fit in my old fobus holder will look up the new ones. Curlyboy
  19. Want to keep the thumb safety but does anyone have a source for the hole covers left by removing the safety as the holes look like a good access for dust getting in your gun? The video says S&W make them would they fit if you can get them? Curlyboy
  20. I gave mine a run out on the range at my local site and as normal for a TM the accuracy was excellent with most rounds hitting where they were put at 50ft distance the gun had no cool down issues even with rapid fire on a fairly cool day but this was to be expected the only little niggle is the gun is so light it feels a little flimsy it is not but just it does not seem as solid as my P226 for example. Curlyboy
  21. I had a WE M&P until the TM was announced it was a nice pistol but i found it was almost impossible to get it to shoot a bull, i do a bit of CQB and i need a pistol to hit as straight as i can and the hop on the WE did not hold the shot always and after a few mags it would drift a bit. I have the TM M&P and sold the WE a while ago so all my pistols are TM (or KSC for the glocks), the hop on the TM is a rugged design and hopefully will suffer with none of the issues i had with the WE, although i love TM pistols i do love the finish on the TM M&P9 although i do agree with some of
  22. I have found the TM M&P fits in the Glock 17 serpa very well and you can adapt the P226 one as well but I am not certain how. Curlyboy
  23. My new belt set up, the belt is custom made but fits like a dream and does not end up around your knees like some I have tried before Pinhead Tactical battle belt 2 x double M4 pouches 1 dump pouch 1 double pistol pouch
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and the use of session cookies.