Jump to content

Gunfighters808

Regular Poster
  • Content Count

    144
  • Joined

  • Last visited

About Gunfighters808

  • Rank
    Regular Poster
  • Birthday 04/14/1976

Additional Information

  • Airsofter since
    1996
  • Country
    United States

Contact Methods

  • Website URL
    http://www.impactgamesairsoft.com www.facebook.com/impactgames
  • ICQ
    0

Profile Information

  • Gender
    Male
  • Location
    Honolulu, Hawaii

Recent Profile Visitors

887 profile views
  1. some video goodness of the scar-H. from Echigoya. so who's going to pop for this badboy? as much as I want one, with the Yen the way it is, it's just too expensive for me right now. anyone in Japan on the pre-order lists? let us know how it is.
  2. that's ok. use the english link on the left hand of page, then afterwards scroll down to the calendar and go back to 01-03-2011. Transration!
  3. kunlun, I've used the PDI 6.05 375mm, fits right in. good overall performance and awesome max range for the system.
  4. looks like Echigoya is now doing a full package upgrade with FET install. I like how they are using the stock insert as the mount/heat sink. anyone get the shortened CQC version from them yet? http://echigoya.militaryblog.jp/e189731.html
  5. just did a MP5 HC for someone. guarder polycarb vented pison head, PDI 140% spring, Kong Power 7.4V 1800mah 26C lipo pack. .20g Excel cronos at 320-324fps, and nice and fast. did a SAS HC with similar set up, PDI150%, on 11.1V pack, same velocity, but 32rds/sec. BEAST. only bad part of that is that you will start to get wear and tear on the pison and gear set at 11V power. can't sustain fire too long too, it's a burst gun.
  6. mostly with the stock piston head, it's the o-ring that might be wobbling around a bit to not make a perfect seal during the cycling in full-auto.(due to the solid piston head face) it still seals good enough to get the shot, but you will see it on the crono. a vented piston head should do the trick. if you are keeping it fairly stock as is, try a Guarder Polycarb Piston Head. (the red one) it's light weight, and won't slow down piston stroke speed like the aluminum ones (slightly lower velocity readings, but better durability with AL) vents keep the o-ring more stable on the forward strok
  7. Great job 'Snoop! in regards to the burst shots in semi, it's from your battery's high burst rating, basically on a fresh charge, it will over-volt the system in semi, causing the burst. 3cell 11.1V packs with lower burst ratings will cause this as well after being charged too. it happens on normal AEG's too. the fps variance is by the fact that the gears and piston are short stroked from normal piston and gear sets. add that the piston head is flat with no ports on the front, that will cause more turbulence in the air cylinder during cycling, it could be the bb's partly too.
  8. as far as the gear set and anti-rev latch, it's the same across the board for the recoil boxes. cylinder heads too I think, (have to re-open a G36 again to make sure ) pistons, air nozzles, hop units, spring guides, and tappet plates are the only gun-type specific. (for spring guide, -sort of, m4 versions are the only different type compared to rest) bushings and cylinders are normal off the shelf AEG. as far as the ak/g36/scar recoil engine is concerned, it's mechanically the same, just the recoil weight/block is different size/weight to gun type.
  9. YES. or at least when I have the time to do another review
  10. AnakChan, I knew you couldn't resist. Nice work! interesting how they went about wiring it up due to the space limitations in the gun body. looks like a fet can be installed, if it can fit in the stock, but you wouldn't want to take it apart again after you install it... I would probably re-solder 20-22guage wire for the signal wires to keep it sorta neat and not take up too much room. the piston is AK/G36. recoil weight is about same as G36 also.
  11. for those with Freedom Art Mag adapters: http://freedomart.militaryblog.jp/e186254.html I kinda like how sensei says it's not hard to shave down to make it fit, unless your lazy. (I think that's what he's implying, through my horrific translation skills)
  12. yes it does. here's some pics, my computer was acting up last time, so I couldn't u/l them. sorry, pics kinda dark, here ya go: video:
  13. The grip options are a welcome thing, that way everyone can be more comfortable shooting this gun. The lock seems to be pretty strong, and the fit is good too. Once the plate is on, it feels really solid.
  14. looks like they're just taking the regular AR-type grip mold that they have and just inject the new color plastic for the gun. cost saving measure.
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and the use of session cookies.