accuracy

Looks very nice, hopefully a little more reliable than my original wem4

Ordered some spare spare parts from ab on 24th in early morning. On the 27th he sent an email saying that order has been shipped and gave me tracking #. I ordered some trigger springs, couple part#66, and a new trigger.

well i could never get my rod to align properly with the stabilizer in the first place. So i just tossed it aside and don't use it. It should be fine considering i've already fired 4000 rounds thru my gun without it. Just make sure you check if it gets loose or anything, or you could loc-tite it as well

ohh. okay thanks guys. do you mean the sear not the trigger? cuz i didn't know that you could wear out the trigger. is there an entire reinforced premade triggerset that i could purchase to save money? otherwise i'm guessing this is what i'll need right?: http://airsoft123.com/index_eproduct_view.php?products_id=6 http://airsoft123.com/index_eproduct_view.php?products_id=7 And do you guys think that my problem with extra gas being expelled after a shot fired could be caused by these parts being worn. Cuz i replaced my chamber and nozzle with the CO2 conv. kit,

well i managed to fix my double feed problem with upgrading to CO2 kit. however, when i pull the trigger to shoot on Full auto mode. The gun will just keep firing non stop until i either pull out the mag or change the selector switch. The reason it does this is because when i let go of the trigger, apparently the return spring isn't powerful enough to overcome the recoil and return it to original position. So if i manually push the trigger forward it will stop firing. Any ideas?

Wow thank you! too bad it cost me 60 bucks.

dear god. I've been looking everywhere for the co2 conversion kit as well for the last month. Only have seen just the new co2 nozzel. but no one has the compatible #111 and #112 chamber to go with it. Someone PLEASE tell me when someone has them in stock. My rifle is useless until then : /

I ordered one online and it woudln't fit right out of the box. I took some calipers and did notice that the RS one is just a tad bit bigger. And eventually i found out that the nubs that stick out of the handle that sides along guide rail inside the receiver were causing it not to go in all the way. For me, i had to file down the sides of it. and from the top a bit. Then it worked smoothly for me.

So it's been three weeks and i've sent this message twice: they're ignoring me now. this is ridiculous

then that sucks because I can't get all the parts I need. Evike says they're ETA sept 15 though... sigh. they're annoying though I ordered the valve and a magazine for 80.73. And i asked to cancel the magazine the day i ordered it It's been a week and a half and they have only refunded the cost of the valve (37.31) after it took them a week to find out that it was out of stock. They have yet to pay me back my magazine and shipping ($43.42). I don't quite understand why it takes so long.

do you need a new gold chamber thing for the co2 valve or can i use the original cuz the nozzel is bigger.

ya but it doens't come with the housing and also it says "* AWSS valve head NOT included in kit. "

Does anyone know where I could find the entire chamber and valve upgrade? http://airsoftbuddy.com/index_eproduct_vie...products_id=370 Evike said it was in stock, but they lie and then 5 days later, canceled my order. So dumb, they still haven't even updated to show it's Out of stock. http://www.airsoftpost.com/awss-stainless-...gn-p-31266.html

well. I just tried to shave the nozzle tip a millimeter (measured w/ calipers). And it didn't fix it, i think it made it worse. Has anyone had troubles yet with this upgrade using propane? http://www.airsoftpost.com/awss-stainless-...gn-p-31266.html

Wow thanks! What you are saying does make sense. I will try that later tonight. much appreciated, but let me try to see if maxing out the hopup will change anything. but it's still wierd since i switched from my 500+ fps valve to my 400fps one. and i've used both valves a lot before with no troubles ever, until just now