GI Tye

And here is a small YouTube video of my modified KWA LM4 with a full auto mag dump at the end. Enjoy.

Its been a while since I have been on this thread. What is the status with Cradle Airsoft and their mags?

If anyone is looking for parts I got them on eBay! Rebuild your whole internals!! http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=280744606108 And a fully upgraded KJW M4 with Cradle Parts. http://www.ebay.com/itm/280744596101?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1555.l2649 Mags, mags, mags... (Search eBay for: KJW M4 Gas Blowback Airsoft Magazine (KJ Works) In Orginal Box! ) http://www.ebay.com/itm/280744602521?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1555.l2649

I decided to switch from Super Lube to Dow 33 grease which was mentioned previously on this forum. I lubed up the piston before the last skirmish I played. After a whole day's battle with the KJW, I took the rifle apart to see how the new lubrication held up and this is what I found: Clearly the Dow 33 grease holds up much better than Super Lube and I plan on using it from now on.

Well I used my KJW in a small skirmish yesterday. It was 75 degree F day out so I was using the single large Cradle Airsoft velocity ring which put me around 350 fps with .25's. My gun was performing wonderfully all day. I could easily over hop the .25g's and I was almost out ranging the AEGs on the field. Everyone was impressed with the KJW. I love this gun!

That is what I want too. I want Co2 mags that are regulated to 120 psi output. That way you can use them year round.

T_Hum How much for the TDC mod and what's the turn around time to have it done? theprodigy Green hopup? Where did you get that?

Do you have the email address??

Anyone have the little o-ring gaskets fall out of the fill valve of the magazines? I have had two do this. Are they needed because I go to fill up a mag, it leaks like crazy without it. Any idea what to use to replace them? Small vacuum hose cut down? Also, can you still order parts from KJW direct? I am looking at buying a list of spare parts and was wondering if contacting them still works. What is the email address? Was it Clare the contact? Thanks for the help!

Two questions: 1. Does the front reciever pin remove like the rear pin? Does it have a detent? 2. What specifics do I need to look for in a quad-rail forgrip/handguard upgrade purchase? I am looking for a continuous flat top, free floating rail system. Any suggestions on brand or tips on which ones swap right on with little effort? Thanks for the help!

All I would need is a level I.

I have been using super lube myself and have been experiencing the same concern. By the time I am done shooting for a day, there is no lube to be found. I personally have felt that I was lubing the piston quite heavily myself. I too have been shooting in below 40 degree F temperatures. Perhaps someone should post a video about the propper way to lube your KJW.

Any time frame on the new may release date? Will they have larger gas reservoir?

Anyone have any tips on this?

I used my KJW for the first time at an Op 4 hours away. I got all of t_hum's parts installed and tested the day before including a 6.01 TBB, bolt extention, velocity adjuster and o-ring piston. After using this fine rifle in abttle I am extremely pleased in its performance, even in weather below 40 degrees F. Most others were having battery problems while I was clacking away in semi all day long. I suffered slight cool down effect which was to be expected on a cold day. I am eager to play with it in warmer weather! After a full day's use on the field I have a couple minor concerns that I