Jump to content

mnmc10

Regular Poster
  • Content Count

    128
  • Joined

  • Last visited

About mnmc10

  • Rank
    Regular Poster

Additional Information

  • Country
    Nothing Selected
  1. mnmc10

    WE M&P

    any review on the we m&p with full auto switch/lever? a local airsoft store told me that WE discontinued it. i wonder why?
  2. mnmc10

    WE MSK Review

    on my friends msk the inner barrel (hop rubber side) is shorter than the regular inner barrel for the m4 scar pdw etc.so a hop bucking made for marui pistols or more known as vsr type barrels wont work on the msk inner barrel.
  3. mnmc10

    WE MSK Review

    the shims one at the back and one at the front of the barrel base the barrel is from a WA/Gnp based gbbr, all i did was to fabricate shims for things to fit properly.
  4. mnmc10

    WE MSK Review

    short barrel msk convertion done you guys wouldnt believe whatouter barrel i used. williploadpics later
  5. mnmc10

    WE Gas Blow Back M4A1 Carbine

    i also use those big orings too. its a bit hard to install at first cause youre pretty much trying to put a round thing in a square canal. i switched back to the stock ones cause the round orings are too thick and is causing the backplate to bend outwards. theoutlier, can you give me the exact oring size you are using? tia!
  6. mnmc10

    WE Gas Blow Back M4A1 Carbine

    regarding the bcg "issue" some say that its better to sand it down so it doesnt catch while it is retracting. but for me its better to leave it as it is cause its a sign that there is a good tight seal between the nozzle and the hop rubber thus making sure that you dont have air leaks. no air leaks means all gas is going to the barrel.
  7. mnmc10

    WE G39C GBB

    slightly loosen those 2 screws located above the nozzle. its the part that prevents the nozzle from going all the way out of the bolt.
  8. mnmc10

    WE Gas Blow Back M4A1 Carbine

    the extra notches mates to the hop assembly and has nothing to do with the hop rubber.
  9. mnmc10

    WE G39C GBB

    you wont regret it cause it is the easiest gbbr to maintain for a newbie. but you do have to dig thru all 61 pages cause there are really valuable stuff you need to know about the g39c.
  10. mnmc10

    WE G39C GBB

    yeah i saw it over at fas, i also converted my m4 to OB. m4 performs at par with my g39c, but i will keep my g39c simply cause of the leakproof magazines.
  11. mnmc10

    WE G39C GBB

    overfilled, over time the magazine is easier to fill. and our weather lately in the philippines is hot. try this, from empty fill it with gas for 10 secs only. see if it can finish 30 rounds. i usually fill mine for 15 secs,has enough gas to finish 30++ rounds.
  12. mnmc10

    WE Gas Blow Back M4A1 Carbine

    just replace the cut up oring which holds the screw in place. i suspect oil got to it and is starting to lose its "plumpness"
  13. mnmc10

    WE Gas Blow Back M4A1 Carbine

    removing the old cb mag kits remove the screw on top, remove the mag lip then pull the follower out from the top, a small wiggle will let it out. the spring might shoot out so watch out for it. putting in the new kits remove one screw from the spring cover the top one only. with a small tool pull the spring down lift the cover then slide the new follower in. the cover is flexible and wont break even if you bend it up so no worries. by removing only one screw on the spring cover you dont have to deal with the spring trying to shoot out from the side. i can convert a mag in less than 1 min.
  14. mnmc10

    WE G39C GBB

    does it really need a steel bolt upgrade?
  15. mnmc10

    WE G39C GBB

    you know the spring guide with bearing for aegs? the bearings in them are just about the same size.
×

Important Information

By using this site, you agree to our Terms of Use and the use of session cookies.