Jump to content

Theoutlier

Regular Poster
  • Content Count

    14
  • Joined

  • Last visited

About Theoutlier

  • Rank
    Member

Additional Information

  • Airsofter since
    2009
  • Country
    Thailand
  1. Theoutlier

    WE MSK Review

    You can order it at either Ratech's website, EBairsoft, BBdragon (the latter is the cheapest I found)
  2. Theoutlier

    WE MSK Review

    So I guess its worth the money? I'm planning on buying it too since I've owned like 3 WE GBBRs and hoping they might share some parts compatibility. Is it a trigger box like their M4 varients? (Another thing I'm really curious about is whether or not it accepts PTS Masada furnitures, if so I would get this gun in a heart beat)
  3. Theoutlier

    WE Gas Blow Back M4A1 Carbine

    Its definitely to do with the design of REAPs (gen2), I had mine on once and the same thing happened. I believe the problem is that the bucking doesnt have this tab thats supposed to sit on the chamber so it doesnt stay properly. Just stay away from them and u will be fine (I recommend using Ra-tech Hops, works great and i put them in all my WE GBBR)
  4. Theoutlier

    WE Gas Blow Back M4A1 Carbine

    its a rounded 2mm diatmeter oring.ofcourse its gonna be difficult to install, but i used the special kind of adhesive (same kind i used to glue the 2 ends of the oring chords together)But i guess u can use super glue?. Few drops of those on the backplate and it stays in place. I also have heard some pple with good result on a 1.5 mm ones. so i suggest u try different sizes. Also to help with the installation, always use superlube on the orings and cclamps to hold the mag together. i tried using bare silicone gaskets and had a horrendous results. But it does good job if u already have oring in place such as this one as it seals all the small gaps the leaks could sprung from.
  5. Theoutlier

    WE Gas Blow Back M4A1 Carbine

    I ve had many leaks from m4 mag. Mostly from the main seal ,Not only that there is more chance of leakage but also orings Are very prone to splitting up( epic Design fail.rlly). So I developed my Own way to remedy this problem. Instead of ordering the same oring as a replacement. Buy a proper industrial orings of 2 mm diameters (they r sold in metres In my country)replace the old 1 with those, cause they r MUCH tougher add some lube and its all set. Mine have had no Single leak since then. U can also try some mods, (there are plenty of em) , Gd luck
  6. Theoutlier

    WE Gas Blow Back M4A1 Carbine

    1. remove Upper from lower 2. take out the bolt 3. look inside, it is a tiny key-hole located just above the Hop-up chamber.
  7. Theoutlier

    One uber massive Costa action figure lying next to the real man.

    so travis is into airsoft, and Costa is into 1:6 action figure?
  8. Theoutlier

    WE Gas Blow Back M4A1 Carbine

    nice one @kullwarrior!!! just put a shim on mine, catch wobbles no more
  9. Theoutlier

    WE Gas Blow Back M4A1 Carbine

    Yep, it works fine now. i filed out some portions of the catch, it nows contact the bolt good. though i have yet to purchase shims, but im pretty sure it would work okay for now. I have also found a mod that works for me so basically if anyone have a problem like "bolt doesnt lock-back on last round " or "bolt locks back when there are still rounds in the mag" then i can almost gurantee its the problem with the spring This can be fixed by stretching the catch spring and/or pushing it down till it stretches or gets thinner. becareful not to over do it though, or you will break the spring. alternatively you can cut the coils or replace the spring, but i find this easier to do.
  10. Theoutlier

    WE Gas Blow Back M4A1 Carbine

    thx kullwarrior for your advice, however, after the close inspection at the boltcatch area, it seems like the bolt carrier is only engaging it at the top bit No wonder why its worned out so much, since so much force is applied on the small area i might try to file the tab that contacts the upper receiver so the catch could go up further btw, how do you find the RA-steel bolt? would it work with stock trigger groups? if not then may i ask what upgrades are you running on?
  11. Theoutlier

    WE Gas Blow Back M4A1 Carbine

    hey guys I too am the owner of we m4, after 1000 or so rounds- it seems to still operate fine, However the only part that i always have the problem with is The BOLT STOP. it seems to be taking alot of damages from the stock bolts to the pont its splitting up!!! (slightly). Im so scared of how worse it would get once i get the RAtech Steel carrier is there any mod to decrease the impact between the catch and the carrier? (besides not using the function ofcourse ) and in your experience, what other major parts would break first? (im talking abt nozzle/trigger group parts) Im having a milsim events in the few weeks so i wanna stock up on spares
×

Important Information

By using this site, you agree to our Terms of Use and the use of session cookies.