Jump to content

Probotector

Regular Poster
  • Content Count

    159
  • Joined

  • Last visited

Everything posted by Probotector

  1. Sorry, "big" was stretching it a bit too much. One gas charge is enough for atleast 1 and 1/2 mags. (home temperature). I still have to test it outside.
  2. Difficult to explain. There is quite some force when the slide slams forward but not so strong that it would damage the slide. Also when pressing the slide catch down, the slide closes fast even when your finger accidently pushes at the slide on the frame (which it doesn't with the stock spring)
  3. It's ACTION 160% for TM1911 GBB's. This spring has a slightly bigger diameter but does not interfere with other parts.
  4. 1.) Because I can. 2.) The amount of cooldown did not change with the different spring.
  5. After fixing the stupid problem with the internal hammer cocking, the gun runs fine. The burst fire issue didn't happen to me and the internals still look good after using the GBB quite extensively. I've replaced the recoil spring with a stronger one (Action M1911), very crisp recoil. The slide and hop up seem to be fine with the stronger spring installed. The only big con of the M&P, not counting in the casting issues with the hop-up and (in my case) the ramp on the loading nozzle frame, is the big cooldown of the mags. But that was to be expected. Overall I'm really happy with
  6. Great submissions from everyone. Loving this thread. I just hope EliteForce/Ares will release their SL9 soon so I can post a G36 rifle aswell.
  7. Man what a sexy sexy gun. I just wonder where I can get a railed Feed Cover seperately? WGC, Ehobby and Uncompany don't have it.
  8. Good news. I actually fixed the issue with the hammer. Folded a little strip of paper thick enough, cut it to the right size and dipped/glued it onto the loading nozzle frame with two-component adhesive. Only emptied one mag, cycles smooth and without any problems. Recoil feels great. Sorry for the bad quality of this picture. The wheel inside the chamber of my M&P kept getting stuck at the corner the arrow is pointing to. Just round it a little and it should do the trick. Also, look if the wheel is deformed.
  9. Damnit. Oh well I found the culprit. There's a little ramp on the frame the loading nozzle sits on where the round piece of the hammer rolls over. It's silghtly lower than it should be. Don't you just love imperfections like these?
  10. Bought it from WGC. I wonder if they'd take it back after I did some work on the faulty hop up. Also when trying to remove the worm screw that holds the rear sight, the potmetal chipped off (who would have thought?) and can't be screwed off anymore. Just ain't my day I guess... Another question: Did WE bring out a Gen2 version of the M&P already?
  11. I also recieved my M&P today. While the gun looks incredibly well done (for WE that is), it doesn't work. I'm not talking about the faulty hop-up chamber, which I was able to fix. Problem is, that it won't cycle properly. If you don't push the slide down while cycling, the hammer will not strain and the nozzle loading gets stuck halfway. The first shot is fine, but the next one causes the magazine to dispense all its gas and sometimes the fullauto issue kicks in (3-4 shots til all the gas went out). Fruitcage!
  12. I can't give you informations in detail as I not only have swapped the Nozzle alone but the whole HU-Chamber and Bucking aswell (Marui instead of Systema). Accuracy over range has definately improved (using 0,25g).
  13. @sacairsoftsn00py: I've put a V2 ARES Stainless Cylinderhead (SOCOM-series) in it. Perfect fit with the WiiTech Nozzle (almost the same length) Parts: Deepfire Titanium Piston (Vollzahn) Prometheus Metal Piston Head + Kugellager Deepfire Cylinder WiiTech Metal Nozzle ARES Socom-Series Metal Cylinderhead Element Silver Wiring + Deans Ultimate 110 Spring Gears Shimming (Ultimate 0,15 & 0,3 Shims) ~432 FPS. Impressive, but 32 FPS too high.
  14. I got the Classic Army SA58 not long ago. I like the externals and I'm gonna upgrade it internally soon. So far the charging lever broke on me. The fake-chamber shuts so hard, it not only ripped the screw from its place but the charging lever broke into two pieces. Why isn't it made of steel...? Damnit. Í guess I'll have to find a used QP for parts, seems like a very nice copy. Good review. Like it.
  15. Wait, really? Good to know thanks. I guess everything else except the motor cage is still V2 (minus propietary Ares gears)
  16. DMR looks sexy. Nice stock! Going to upgrade my Masada soon to 390-400 FPS. I wonder what you guys used for the internals. To-buy-list: - Deepfire Titanium Piston - Ultimate M110 Spring (with good compression, otherwise M120) - Prometheus Aluminium Piston Head - Wii Tech Nozzle - Wii Tech Spring Guide Too bad I couldn't find an appropiate V2 cylinderhead with a long nozzle while shopping on eHobby. I may change the cylinder as well.
  17. I'll use a MVG foregrip for the rail under the handguard. The siderails are just decoration, I like the contrast between the black polymer rails and tan body. I'll probably put rail covers on the siderails.anyway. I really don't like the RIS. The shape of the original handguard looks better imo. I like ridiculous stuff, can't have enough rails. ;P
  18. Masada PTS olololol Great externals, hop up design sucks though. I accidently bent the hop up nub by removing the barrel and not turning the unit off. Bent it back to normal and wound a small layer or teflon tape over it. it barely had any hop before, no it works fine (in conjunction with Systema rubber). No tools at home, looking forward to get it upgraded from another player I met (~400 FPS). Oh, and I'm not buying the RIS, looks ###### IMO. ;-) And troll flash hider is trolling. Will be replaced with a XM177E2 one.
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and the use of session cookies.