Jump to content

Raketen

Members
  • Content Count

    20
  • Joined

  • Last visited

About Raketen

  • Rank
    Member
  • Birthday 05/20/1993

Additional Information

  • Airsofter since
    2012
  • Country
    Denmark

Profile Information

  • Gender
    Male
  1. I got a blue a&k m110 cylinder but it doenst feed with high rof.. Does anyone know a fix? I've heard that the supershooter cylinder should be the best.
  2. A&K hops are a hit or miss i've had to a&k ptw's the first was perfect, the most precise thing i've ever tried (try alot of weapons!) But my second is terrible, the lips the "nub carrier" sits on are not stright, so the pellets curve after 20 meters. Though it still have plenty of hop! i've bought an FCC gen2 hop-up champer, wich is not the best... some say it have to be broken in, but it cannot even lift a 0.25g......
  3. i dont know if its right to ask in tis thread. Buts a general ptw question. Do any of you guys use a MOE pristolgrip? And if so, how do you protect the motor from sand and water/moist?
  4. Update again! The beast is now finally running! The parts i've bought is: Etiny mosfet (no mods needed) Etiny ecu (no mods needed) Etiny switchboard (no mods needed) FCC 6.03mm innerbarrel (no mods needed) FCC adv. gen.2 hop-up (no mods needed) FCC motor 3.0 (needs to be filed to fit)
  5. how many of you have tried aftermarket motors on yor a&ks? I just got my FCC 3.0 motor, but i doesnt fit. The curved groove that goes on to the receiver is too wide(not the pin grooves). So im a little concerned what to do now is it normal that the motors are a bit of spec?
  6. Heh a little update on my a&k project(as it has become) I installed my etiny electronics (ECU, MOSFET, and switch), yesterday, and they fitted perfectly, and the gun fired again! but after 50 test shots, it began doing half cycles and 1/10 cycles, and i figured it was because of a "cold" solder connection. so i resoldered and it fired perfectly again. But only until the plastic "towers" holding the springs on the motor snapped.... . After some time trying to get the motor working again, i just thought maybe it was time for the fcc 3.0 upgrade, the ROF on the stock motor was way to low any
  7. think i've read that the original is not the same dimension as others. (not shure though) What kind of rof are you getting with the new motor?
  8. Okay great thanks! wil i need to buy the Etiny switch board?
  9. Okay guys i dont know if its me thats just unlocky... So i send bak my A&K to gunfire.pl. And they send me a new one, but it wasnt assembled that well. The buffertube was a bit loose, and had chewed a wire for the mosfet.... i dont want to bother with it, because its porbably going to be changed anyway. Has anyone tryed a etiny ECU and mosfet in the A&K PTW? Im also lookeing into buying a fcc 3.0 motor.
  10. In what country do you live? i got one for sale as it did not fit the a&k PTW :'( if you live in side EU, you could buy from me for 80Euro shipping is between 10-20Euro i think
  11. The problem is there isnt any visible errors the tooth rack is perfect. Maybe i should make my own thread?
  12. there is no led in the A&K mk4 that i know of
  13. hm wierd i just used the gun some hours ago where it was working fine. i have tried with two different cylinders. but same reslult. How can it be fixed? and if its not catching the cylinder, why wold it stop running when closed?
  14. Hi again i just encountered a new problem. When i open op the ptw the gears cycle fine. But when i close it and shoot, the motor just spins for a second and then stops and won't run before i replug the battery. any one got a solution for this? http://www.youtube.com/watch?v=D7MutKpFu6A&feature=c4-overview&list=UUiSHolO-rkvdtaRZTvsdwlw
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and the use of session cookies.