farrasdevell

best thing about the alenco dj446 is you can run it off aeg batteries if yours goes down Deviat PM me if you want a guide to change your transmision powere to .5w or 1w output.

how about getting a side mount hydration pack? like this one Being shorter it is ideal for the little pannel on the back. which sits miles too low for attaching a map or such.

i am currently trying my damndest to pick one up 2nd hand for cheap. am mspainting a diagram now for measurments needed.

quick math says you need to have a cylinder/gas output of 31cm3, will try and work that out in blot terms later. (allthogh i seem to recall someone saying it may be cylinder= barrel volx2 will check)

with such a long barrel you also need to concider the piston/gas output volume -v- inner barrel volume. Perhaps this has been the problem from the start, if the cylinder/gas output is not euqal to or greater than the volume of the inner barrel then the bb will not exit the barrel under pressure and will have no 'air cushion' (the air that flows around the round) just chucking that out there. It may also nesecitate minor porting of the outer barrel. Can anyone give the inner diamiter of ther outer barrel. seems to me it's just a case of inefficiency.

loving the look of the mk7

^tom843^ Doood that g36 is huuge one you, i had to look twice to make sure i was seeing right Damm right that was a 5 knifekill crazy day for me, i was on top form

Yesterday. The red on my was my team colour i was sniping earlier in the day and like to keep my team colour low. the red tag on my chest is my chalker sling pull.

Great set of pic ACES, welcome to Arnies.

needs locking is what it needs.

Bravo sir ^^

elcan spectre i see there? ^^

lo the multi-tool int the 2nd from left pouch could almost be mistaken for a speedloader>

apart from the wiring yep it is (was) totally stock. I took it apart to clean it and change the spring to an m100. It could do with a total reshim as it is noisy as hell but it is shooting straight and very consistently as is so i am relucant to change anything. I took the breach block to work today and set about chopping it down in the same way RA-Tec do to make thier lipo kit 2 simple cuts with a standard hacksaw. Now i just need to order in a couple of lipos and find someplace to hide the mosfet. This gun is inline to take over as my primary since my vsr decided to go to the wall again.

Used mine for an almost full day on sunday and aside from just being fookin noisy it was an awesome little shooter> i did have to do an almost total rewire after melting the tamya connectors off. am looking at a different motor next.

a great and practical application for a charity event.

man i love flints such an awesome company Blackwater Esotonia i take my cap off to ye that is some mighty impressive setup you have there.

i had one for all of about 45 mins. It turned up witht he postman and 30mins later it was back in the box and re-wrapped to go back to the postoffice. Why? The reach was too far, from buttplate to pistol grip was about 3inches too long. The buttplate just feels too wide (even framed up against the famas) The mars sight, what is that meant to be a 1MOA dot? anyways it was a little bit sunny outside with patches of cloud and when the sun came out the dot vanishes. the adjustmens were unmarked and non-click/lock Laser, slightly temperamental and when zeroed is blocked by the front

am taking this out today, Will report back.

have yet to realy run it out in a game, been snipering(sic) alot and havent used it. Will do soon.

Bioval!! Aren't they like made of depleated uranium or something? They go through walls Ok fanboy quote of the day over. They have had some good press, and I have seen them used in a sniper rifle abd they are pretty good might pick some up for comparison. ,

small victories of the day. 1: Using hot glue i have succesfully replaced the god awefull hop rubber that was in the gun. I will order more but this works pretty well as is. 2: Due the wait time on nozzle assemblies i DIY'd my floating valve. from my local model shop i got a length of 3/16 x .014 (5mm) pvc pipe which sits nice and snug inside the stock valve and boshed a weee hole in it I might put a tiny dap of super glue in there later but it seems solid enough and doesn't rotate easily . Tidied it up a bit and tried it out, lack of chrono doesnt help but ye olde coke can test says 30

just got my m4 home and am experiencing my first pangs of buyers remorse! why oh why ohwhy why did i not buy MORE MAGAZINES this is sooo much fun and pretty spot on aside a wonky hop nuby. 2mags is not going to be enough

i use this in all my gas guns it is dirt cheap, kicks well and is in far better sized bottles (short and fat over tall and thin bernzo bottles) also they are tacticool black not blue. edit= pic for size comparison hi-capa5.1, coleman bottle ontop of a medium utillity/dump pouch. Picking up my WEm4 today but this gass bottle has filled about 40 hi-cappa mags and my vsr gas bolt about 15 times.

My lastest and pretty awesome aquisition. $17.50 +p&p from ehobbyaisia does a great job in a tight little package. piccie