kenxin Posted December 17, 2011 Report Share Posted December 17, 2011 How is that Detonator threaded barrel treating you? I like it a lot. It doesn't scratch the hop-up chamber like the guarder/shooter's design ones and the fitting is better. The only downside is that its not as hard as the shooter's design slide so it's more easy to scratch. Oh and its CW....sadly. I'm fairly impressed with Detonator, I'm also going to order their 10-8 sights for a 1911 project I'm working on. Quote Link to post Share on other sites
Wild_XIII Posted December 17, 2011 Report Share Posted December 17, 2011 I whited the trades on my Glock and I think it looks much better than just having the trades engraved. What do you guys think? The pictures show up some smudging where I didn't manage to get rid of all of the excess tip ex (yay for bodge jobs!). But to be honest if you aren't looking for it you can't notice it. Quote Link to post Share on other sites
Andrew March Posted December 17, 2011 Report Share Posted December 17, 2011 Looking good Ollie mate, a quick spray of oven cleaner wiped off after 30 seconds will get rid of the smudges mate, Quote Link to post Share on other sites
Asterix1977 Posted December 17, 2011 Report Share Posted December 17, 2011 I whited the trades on my Glock and I think it looks much better than just having the trades engraved. What do you guys think? The pictures show up some smudging where I didn't manage to get rid of all of the excess tip ex (yay for bodge jobs!). But to be honest if you aren't looking for it you can't notice it. Why would you use tip ex? Use some water based paint: it will not go away if its IN the engraving, but the excess can be cleaned of with a wet piece of cloth. Thus, you dont have to paint it carefully: you just paint all over the trades and clean the paint outside off. And it's non-permanent, should you get tired of the job. Quote Link to post Share on other sites
Wild_XIII Posted December 17, 2011 Report Share Posted December 17, 2011 I used tip ex as I've used it before on other things. You can do exactly what you describe above but instead of using water use a tiny amount of white spirit (checked that it doesn't do any damage to the slide). I also had nothing else around at the time and it was one of those "I want to do it now" jobs. It's been painted into the engraving so it's not coming out easily, it's the same on my scar's stock numbering and that's been going for ages! I'll try the paint next time, sounds a little easier. Thanks for the input. Quote Link to post Share on other sites
Bando Posted December 17, 2011 Report Share Posted December 17, 2011 is there a GBB of the 17L model? Quote Link to post Share on other sites
aznriptide859 Posted December 18, 2011 Report Share Posted December 18, 2011 I believe MGC made one, but none by more modern manufacturers. TM made a springer. Quote Link to post Share on other sites
AliasJim Posted January 3, 2012 Report Share Posted January 3, 2012 (edited) Glock 17 : HD pics available on Quick n Efficient Glock 22 : HD pics available on Quick n Efficient Enjoy Edited January 3, 2012 by AliasJim 2 Quote Link to post Share on other sites
Ivan le Fou Posted January 3, 2012 Report Share Posted January 3, 2012 I am jealous of your G22 outer barrel. I haven't received mine when I ordered it to Unco and they don't want to send me one. Quote Link to post Share on other sites
starburst Posted January 7, 2012 Report Share Posted January 7, 2012 Great Glocks, they TM/KSC/KWA/other based Quote Link to post Share on other sites
Ivan le Fou Posted January 12, 2012 Report Share Posted January 12, 2012 Quote Link to post Share on other sites
Top Posted January 12, 2012 Report Share Posted January 12, 2012 Though I would share my 19 KSC Glock 19. Quote Link to post Share on other sites
RacingManiac Posted January 12, 2012 Report Share Posted January 12, 2012 A newer vid of my steel slide Glock...didn't lock back after 17 round, might need more tinkering. I've changed around the recoil spring to get it to return a bit more snappily(basically a hi-capa spring along with the 200% guarder spring that the slide comes with...) 1 Quote Link to post Share on other sites
Bladerider Posted January 12, 2012 Report Share Posted January 12, 2012 Thats nice racingmaniac! Looks like it cycles at normal speed even with the slide Quote Link to post Share on other sites
RacingManiac Posted January 14, 2012 Report Share Posted January 14, 2012 Added SD's polymer Glock magwell, and pic of the Hi-Capa spring setup.... Quote Link to post Share on other sites
BattleForceTactical Posted January 15, 2012 Report Share Posted January 15, 2012 I know I've asked this a couple of times in other places, What Holster will fit a KWA/KSC G19? I've been using mag pouches but afew times diving etc I've lost it several times, Would it fit a G17/G22 holster? I'm looking for something like a SERPA or a KYDEX one... Any ideas? Quote Link to post Share on other sites
RacingManiac Posted January 15, 2012 Report Share Posted January 15, 2012 When I had a KSC G19 I had a Fobus Glock holster. That seemed to work pretty good. That holster don't work so well with TM Glock though... Quote Link to post Share on other sites
BattleForceTactical Posted January 15, 2012 Report Share Posted January 15, 2012 When I had a KSC G19 I had a Fobus Glock holster. That seemed to work pretty good. That holster don't work so well with TM Glock though... Similar design to what Im used too.. Cool I'll go check out my local store! Thanks Quote Link to post Share on other sites
TeowneD Posted January 19, 2012 Report Share Posted January 19, 2012 Similar design to what Im used too.. Cool I'll go check out my local store! Thanks I've got the same gun dude, it works spot on with a Glock 23/19 serpa holster. you can usually find them cheap on ebay. -brendan 1 Quote Link to post Share on other sites
Tek-Spec Posted January 19, 2012 Report Share Posted January 19, 2012 My 2 Glocks, Both Marui, Both upgraded internally/externally. 1 Quote Link to post Share on other sites
Grindstone Posted January 19, 2012 Report Share Posted January 19, 2012 I know I've asked this a couple of times in other places, What Holster will fit a KWA/KSC G19? I've been using mag pouches but afew times diving etc I've lost it several times, Would it fit a G17/G22 holster? I'm looking for something like a SERPA or a KYDEX one... Any ideas? KSC/KWA G19s generally fit in any holster made for a G19, and even G17/18. I used to carry my KWA G19 in a BHI G17 SERPA. 1 Quote Link to post Share on other sites
BattleForceTactical Posted January 19, 2012 Report Share Posted January 19, 2012 Cool thanks guys. ordered one anyhow Quote Link to post Share on other sites
kojak Posted January 19, 2012 Report Share Posted January 19, 2012 Thought I might as well try it with a can, since I'm using the Gun Clip: Has anyone seen the Viridian holsters in person? Not much info out there, and I wonder if I'd be happier if I molded my own. Quote Link to post Share on other sites
oRb Posted January 20, 2012 Report Share Posted January 20, 2012 (edited) Custom COD Style Glock 18 GBB Specs: Tokyo Marui Glock 18C Semi / Auto GBB Based GunsModify Parts: CNC Aluminum Slide Kit For Marui Glock 18C (BK, BK Barrel), Extended Slide Stop, Lower Frame Series Tag & Tritium Night Sight Guarder Parts: Original Frame (OD), Steel Magazine Catch, Polycarbonate Loading Muzzle & Piston Lid FALCON 6.03 Precision Inner Barrel Set for Marui G17/G18C GBB (97.5mm) NINE BALL Parts: Air Seal Chamber Packing & Recoil Spring Guide PRO Firefly Cylinder Valve For Marui G18C GBB MAG Replacement Spring Set for Marui GLOCK Series GBB Shooters Design Parts: 150% Hammer Spring, CNC Steel Valve Knocker, Steel Full Auto Sear 18C-60 & Magwell + Lanyard Hook Tokyo Marui Glock Series 25 Rounds Magazine with Guarder High Output Valve & Shooters Design TM G17 Magazine Base With Logo x3 Tokyo Marui Glock Series 50 Rounds Magazine with Guarder High Output Valve & Shooters Design TM G17 (+2) Magazine Base With Logo x2 Pics: Matching Serials of course: The Gunsmodify Slide Kit is a copy of the SD Slide Kit but totally lightweight. Even lighter then the PGC Kit. Regards orb Edited January 20, 2012 by oRb 1 Quote Link to post Share on other sites
Ivan le Fou Posted January 21, 2012 Report Share Posted January 21, 2012 Kojak >> how does the X5L performs? Is this the copy or the original one? Does is fit in the Crye holster? *if you have one* Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.