Jump to content
krame

Glock Picture Thread

Recommended Posts

OMFG!

 

Coolest stippling job I've seen on a Glock, yet. It looks so, uniformed, unlike the random stippling.

 

Awesome job. So clean.

 

Thank you my good sir, I appreciate the compliment. :)

 

Here's a TM G26....

 

 

IMG_0055.jpg

 

 

IMG_0053.jpg

 

 

 

IMG_0057.jpg

 

 

 

IMG_0056.jpg

 

 

 

 

 

Quick question for you Glock experts though. I am in the market for a G17 as a sidearm to play with and I'm pretty much after a brand that will give me a good fill up on the mags and have enough power to cycle every round in the mag. I had a TM G17 3rd Gen. a few years ago and I wasn't really happy with that gun since the mags wouldn't fill up without spewing and I would rarely get a full mag out of each fill.

 

Pretty much I guess I am wondering if you guys have any advice as to what mags will fill up similar to the WE 1911 style mags where all the gas goes in without any spewing or fizzing. :)

Edited by jdizzle921

Share this post


Link to post
Share on other sites

Not sure why you are so bent on not spewing, on most KSC/TM/WA, when it start spewing its full.....

 

I can cycling a 2 full mags on a STEEL slide, 200% recoil spring TM G17 on one fill in ~20 deg C. Shooting ~0.5-1 sec per shot...

Share this post


Link to post
Share on other sites
Not sure why you are so bent on not spewing, on most KSC/TM/WA, when it start spewing its full.....

 

I can cycling a 2 full mags on a STEEL slide, 200% recoil spring TM G17 on one fill in ~20 deg C. Shooting ~0.5-1 sec per shot...

 

 

I guess it's just what I'm used to associating with a solid performing gun. All the GBB's I've owned in the past that filled up "Fully" (I guess you could call it) all performed when I needed them to while playing.

 

Then came my TM Glock. I had to draw it instead of reloading during a game on two occaisons and both times it let me down after firing a few shots...LOL.

 

As long as the KSC/KWA's end up with a full fill of gas in the magazine after spewing a bit, I'm fine with that. I just didn't like my TM since I could sit there and fill it for 30 seconds or give it quick bursts of gas and it still wouldn't fill up. I would normally chalk it off to being a bad mag, but the 4 TM mags all did the same thing, and when I tried two old mags from a KSC/KWA I had about 8 years ago, they both filled up "Fully" and performed flawlessly.

 

So, any suggestions as to what you guys would get if you were in my position? :)

Share this post


Link to post
Share on other sites

I don't know, for me fill valves with no oring (like Marui) are easier to fill than the silent fill valves (with oring).

 

Btw the fill valves with no oring allows the magazine to have more gas while filling, there is a reason why it sprays a little of gas while you are filling it...

Share this post


Link to post
Share on other sites

I have to echo others statements and point out that high end GBB's tend to have to "venting" system while cheap clones have the silent fill system. The spewing gas is a plus because you know when your mag is full. With a silent fill valve you just have to guess. The spewing also allows you to purge all the gas out and fit as much liquid into your mag as possible.

 

To be honest, your experience sounds more like an empty gas can than anything else.

 

As far as gas consumption goes, I easily get a full mag with a heavy steel slide and 150%+ recoil spring even when the temperature is as low as 50F.

Edited by Romulus

Share this post


Link to post
Share on other sites
Don't have a legit camera. TM g17 with beadblasted PGC slide

 

did you have any problems fitting the pgc slide? mine gets caught about 1cm before returning to battery. it's also much more difficult to rack and i cant figure out what it is that is preventing it from cycling.

Share this post


Link to post
Share on other sites

Did you screw in the setscrews for the extractor all the way or is there any excessive material around the drillings.

 

I have a PGC on my GLock 19 and it is nothing but great. Runs very smoothly (even with the sharp edged chamber) and has 0 wobble whatsoever.

Share this post


Link to post
Share on other sites

Work in progress. Dual, full auto, extended mags, white-slided, electric Glocks. To do: Get nightsites, fix a bit of the paintjob, glock grip panels, minor fixes.

 

DSCF6531.JPG

DSCF6532.JPG

DSCF6533.JPG

DSCF6534.JPG

DSCF6536.JPG

DSCF6537.JPG

DSCF6539.JPG

DSCF6541.JPG

DSCF6542.JPG

Edited by Cosmitz

Share this post


Link to post
Share on other sites

Well, i'll get a mate to paint a red cross on both of them, and write "Primum non nocere" and "Cura te ipsum" on each. They will then go inside a First Aid aluminium box.

 

Yes.. They are 'medic' guns'. :)

Share this post


Link to post
Share on other sites

Well, when you're forced to run half a forrest to get to a guy 'bleeding out' then you certainly can't have a 5kg primary holding you down. Dual auto's do wonders and can supress areas quite nicely. ;p

Share this post


Link to post
Share on other sites

AEP's, and i can't use any extended-er mags. I'm limited to midcaps by the general consensus airsofting rules in my country. Midcaps are defined as 3x max of the real capacity, so 90 rounds max. The airsoft Cyma ones are kinda sucky, and fail around the 60-80 point mark anyway so i'm safe. Got a bit of extra kit on them, and will go ahead with the painting next week. Will post another set of pictures later on.

Share this post


Link to post
Share on other sites

Haha...yep that's the stock slide pforce. Yours definitely is twins with mine as well. :)

 

Cool idea with the "Medic" gun loadout as well Cosmitz. Most medics I see at fields are just normal players who volunteer for the day with their SAW's or M60's and can't really do much as a medic. But with a much lighter and speedier loadout like that, you'd definitely be a lot more use to your team. :)

 

Also, any insight to my ramblings above on a "Gamer" Glock 17? I'm still kinda torn on what brand will perform the best.

Share this post


Link to post
Share on other sites
Haha...yep that's the stock slide pforce. Yours definitely is twins with mine as well. :)

 

Cool idea with the "Medic" gun loadout as well Cosmitz. Most medics I see at fields are just normal players who volunteer for the day with their SAW's or M60's and can't really do much as a medic. But with a much lighter and speedier loadout like that, you'd definitely be a lot more use to your team. :)

 

Also, any insight to my ramblings above on a "Gamer" Glock 17? I'm still kinda torn on what brand will perform the best.

 

KSC. Nuff' said.

 

For ultra performance- Run something like mine.

 

Metal Slide- of your choice. I had the G&P, but my threaded barrel tore it up, and so I got the PGC. Awesome, light, smooth. I was considering the ProG4 one. They have a slide, not custom built, but a pretty basic one on their site.

Tightbore- PDI 6.01. Cost quite a dime from AirsoftAtlanta- only place I could find it in stock, but I get groupings within an inch at roughly 25 yards.

 

Floating (Rocket) Valve- The KSC G series one major weakness. I have the Firefly- the only one I could find in stock. It does it's job, and a nice metal. I also saw that UnCompany has the Airsoft Surgeon one in stock. Or was it SD? One of the two.

 

High-Flow Valves- Really just shooters choice.l I wanted my monster to be at it's best.

 

Aesthetics- I smacked a Guarder threaded barrel on mine, and ran a KA light weight Mock Slim suppressor. The Guarder barrel was so strong it chewed up the G&P slide and it no longer seated properly.

 

Mnay of these things are optional. The only one you will likely have to get is the Rocket valve. I didn't need mine until around round 18K

Share this post


Link to post
Share on other sites

KSCG182.jpg

 

KSCG181.jpg

 

Parts List-

KSC G18C w/ Metal Slide, Taiwan Model

PGC G18 Metal Slide and Outer Barrel

Firefly Rocket Valve

Guarder Recoil Spring

Hogue GLOCK Grip

 

Of interesting note is that the stock rocket valve is made of aluminum, not plastic like my KWA G18C. I'll probably replace the stock inner barrel with a PDI G34 tight-bore.

 

-Piano

Share this post


Link to post
Share on other sites
KSC. Nuff' said.

 

For ultra performance- Run something like mine.

 

Metal Slide- of your choice. I had the G&P, but my threaded barrel tore it up, and so I got the PGC. Awesome, light, smooth. I was considering the ProG4 one. They have a slide, not custom built, but a pretty basic one on their site.

Tightbore- PDI 6.01. Cost quite a dime from AirsoftAtlanta- only place I could find it in stock, but I get groupings within an inch at roughly 25 yards.

 

Floating (Rocket) Valve- The KSC G series one major weakness. I have the Firefly- the only one I could find in stock. It does it's job, and a nice metal. I also saw that UnCompany has the Airsoft Surgeon one in stock. Or was it SD? One of the two.

 

High-Flow Valves- Really just shooters choice.l I wanted my monster to be at it's best.

 

Aesthetics- I smacked a Guarder threaded barrel on mine, and ran a KA light weight Mock Slim suppressor. The Guarder barrel was so strong it chewed up the G&P slide and it no longer seated properly.

 

Mnay of these things are optional. The only one you will likely have to get is the Rocket valve. I didn't need mine until around round 18K

 

 

Thank you Brooklyn. EXACTLY what I was looking for. You wouldn't happen to have any pics of that setup you'd like to show off would you? It'd be awesome to see what the finished product looks like. ;)

Share this post


Link to post
Share on other sites
Thank you Brooklyn. EXACTLY what I was looking for. You wouldn't happen to have any pics of that setup you'd like to show off would you? It'd be awesome to see what the finished product looks like. ;)

 

Nothing updated, sorry. I just have the build with G&P slide and cheapo suppressor.

 

2960169178_8b2f494841.jpg

Share this post


Link to post
Share on other sites

Dang, someone else finally found another PGC G18 slide. I was hoping that mine was the only one that would ever turn up. I guess that I still have an edge with the Gen. 2 frame though.

 

Anyway, that looks lovely, where did you find it?

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×

Important Information

By using this site, you agree to our Terms of Use and the use of session cookies.