Hedganian Posted June 10, 2010 Author Report Share Posted June 10, 2010 Sorry, what was your question? But yeah, um... You're welcome. Link to post Share on other sites
mugur Posted June 10, 2010 Report Share Posted June 10, 2010 given the 72,234% posts i've read here that are just "saying" without asking anything, it is my mistake for not fully undestanding the whole "purpose" of the thread. umm... yeah. Link to post Share on other sites
wilekcmc Posted June 14, 2010 Report Share Posted June 14, 2010 Couple of questions for you on the AUG, yes i have looked over the hepldesk here and the picture thread, so please don't shoot me. 1, There is is a small problem with the version 3 mechbox moving back wards over time but can be fixed with a easy mod? 2, Easy to change out barrel setup between games by loosing a couple of screws (warning be careful of the hopup unit, wears out over time)? 3, Only difference between the TM, JG and CA mechbox is that the CA uses 7m bushing in there's and not all parts will fit the CA AUG? So if all of the above is correct you have a AEG that can fit QCB, standard assault riffle and snipper roll's, all you have to do is change out your barrel setup? If i am wrong please tell me so. thanks Link to post Share on other sites
Hedganian Posted June 14, 2010 Author Report Share Posted June 14, 2010 I've not had a problem with the gearbox migrating backwards. The panel that separates the battery compartment from the gearbox should hold it in place. There are no screws holding the barrel module in place. Simply hold the cocking handle to the rear and press the barrel release catch and slide it off forwards. Make sure you've not got a magazine fitted when you do this! There does seem to be some minor differences between the CA and TM AUGs. The JG seems to be identical to the TM in every way that I'm aware of. The CA is generally higher quality though, has better trades and so forth. The AUG - with an outlandish input of cash to acquire spare barrel parts which are not easy to come by - can serve any purpose you want with only one gearbox. See the photographs of Project AUG for information on this. Link to post Share on other sites
Docv400 Posted June 14, 2010 Report Share Posted June 14, 2010 ...1, There is is a small problem with the version 3 mechbox moving back wards over time but can be fixed with a easy mod? ... The standard gearbox 'retaining' plate is plastic. It's strong enough but can crack around the two screw holes, especially if the gun is dropped or roughly placed butt-down on the ground too often. Also, I think the rubber pad on the plate that bears on the back of the gearbox compresses over time, allowing the gearbox to move rearwards slightly. A metal replacement is easy enough to make, with a more durable pad as well you shouldn't have the problem. It can also usefully double-up as a heat-sink for your MOSFET...what do you mean you don't have a MOSFET? With a metal plate, you can also afford to make it 'minimal' enough to make room for an axtra cell on a ('humpback') minipack. Link to post Share on other sites
Treadhead Posted June 14, 2010 Report Share Posted June 14, 2010 3, Only difference between the TM, JG and CA mechbox is that the CA uses 7m bushing in there's and not all parts will fit the CA AUG? thanks MY CA has 6mm bushings, but it's from a early batch so it may have changed over time.... Internally, the CA and TM models are identical and fully interchangeable. The only major difference between the boxes is the CA gearbox has a different sliding plate on top with a different way of mounting the ejector cover (better than the TM design imo). Link to post Share on other sites
Hedganian Posted June 24, 2010 Author Report Share Posted June 24, 2010 MY CA has 6mm bushings, but it's from a early batch so it may have changed over time.... Internally, the CA and TM models are identical and fully interchangeable. Got to stop you there, I'm afraid. The part which feeds BBs from the magazine into the hop-up chamber (ST-20 on the TM parts list) is not the same on the TM and CA versions. If you've got the whole assembly from a CA one, it will work in a TM, and likewise a TM will work in the CA, but you can't make a working one from some CA parts and some TM parts. If that makes any sense? I, of course, mean this part: (That's the TM version) As far as I can tell, the actually gearboxes themselves are as near to identical as makes no difference, and gearbox parts which work in one version will work in all versions. Likewise with external cosmetic parts such as rails and things of that nature. The barrel parts are certainly and most definitely interchangable... Link to post Share on other sites
Treadhead Posted June 25, 2010 Report Share Posted June 25, 2010 Fair point O picker of nits.... I was talking about the gearboxes mind.... Link to post Share on other sites
Phuncz Posted June 27, 2010 Report Share Posted June 27, 2010 That gearbox plate of mine is pretty useless at the moment, as I lost one of those square nuts that hold it in place. I'm also looking for another hopup rubber cover so if anyone knows where I can get both, I'd be a happy man ! Link to post Share on other sites
Treadhead Posted June 27, 2010 Report Share Posted June 27, 2010 define hopup rubber cover... I've got a couple of stock hopups knocking about... I'll have a look for one of those nuts too - should have one! Link to post Share on other sites
Phuncz Posted June 29, 2010 Report Share Posted June 29, 2010 I mean the rubber cover on the stock that covers the hopup, that long flat piece. I removed the pull-back metal shield in mine for multiple reasons and ducttape looks shoddy plus sounds awful. Link to post Share on other sites
godwin Posted June 30, 2010 Report Share Posted June 30, 2010 You mean the Port-Cover: http://www.wgcshop.com/wgc2008/main/product_detail1.php?search_From=searchItem&item=CA-PT-AUGPC&search=special&rs=port%20cover&catid=&cat= If you dont find the AS-Part, try to look for the RS-Version. Should fit. I need this part: http://www.wgcshop.com/wgc2008/main/product_detail1.php?search_From=searchItem&item=TM-PT-AUG-ST3&search=special&rs=aug Its sold there, where can i find it? Link to post Share on other sites
Hedganian Posted June 30, 2010 Author Report Share Posted June 30, 2010 It would be really helpful, guys, if when asking about parts, you could refer to the TM parts list and give the ST code so we're all on the same page. The TM Parts list is linked in the first post of this thread. I think I sold my spare flat-top receiver rail. Leonardinjapan might be able to get it, if he's still around. See one of Stunt's posts earlier in this thread for more information. Failing that, you'll have to keep checking around the for sale forums to see if someone's breaking an AUG and buy the receiver. Link to post Share on other sites
Daniel Fernandes Posted July 22, 2010 Report Share Posted July 22, 2010 Hello there. The last place I was expecting to have the PDC Hop chamber, as indicated here, was DenTrinity. Today I was going to buy it and they said it is sold out... So, I come here to ask if anyone knows a shop with it stocked or if someone has one extra to sell... I am tired of my lack of accuracy... Link to post Share on other sites
Hedganian Posted July 22, 2010 Author Report Share Posted July 22, 2010 This is really a thread for problems with the AUG, not supply problems. Surprisingly, I don't have the stock lists for every airsoft retailer on the planet commited to memory... The last ones I bought came from WGC, if I recall correctly. But that was some time ago... Link to post Share on other sites
kommando kat Posted August 20, 2010 Report Share Posted August 20, 2010 Does anyone have experience with the HP AUG hbar kit? I am planning to get this along with a CA AUG A1 so here are a few questions I want to clear up before I make my purchase... Does it fit the CA AUG? Is it sturdy enough for skirmishing? Will it affect the performance of the gun? is the metal hopup good enough for occasional barrel swaps? Is the gun's hopup good? Is it a good DMR setup? Do I need to modify it to make it fit/work? thanks... Link to post Share on other sites
kommando kat Posted August 20, 2010 Report Share Posted August 20, 2010 Does anyone have experience with the HP AUG hbar kit? I am planning to get this along with a CA AUG A1 so here are a few questions I want to clear up before I make my purchase... Does it fit the CA AUG? Is it sturdy enough for skirmishing? Will it affect the performance of the gun? is the metal hopup good enough for occasional barrel swaps? Is the gun's hopup good? Is it a good DMR setup? Do I need to modify it to make it fit/work? thanks... (btw I mean the full barrel assembly not the kit that makes you screw on the parts) Link to post Share on other sites
tgellen Posted September 12, 2010 Report Share Posted September 12, 2010 Does anyone have experience with the HP AUG hbar kit? I am planning to get this along with a CA AUG A1 so here are a few questions I want to clear up before I make my purchase... Does it fit the CA AUG? Is it sturdy enough for skirmishing? Will it affect the performance of the gun? is the metal hopup good enough for occasional barrel swaps? Is the gun's hopup good? Is it a good DMR setup? Do I need to modify it to make it fit/work? thanks... (btw I mean the full barrel assembly not the kit that makes you screw on the parts) Yes, yes, yes, yes, I don't know, Better as a SAW (LMG), nope. Link to post Share on other sites
godwin Posted September 25, 2010 Report Share Posted September 25, 2010 Although its in german, i think my tuts can help someone (lots of pics, you can use babelfish or google for translating to english): How can i disassemble the AUG V3 Gearbox?: http://forum.airsoftaustria.com/showthread.php?t=39212 How can i tune the trigger of an AUG? Removing the Semi resistance: http://forum.airsoftaustria.com/showthread.php?t=39216 Better Sound and shorter trigger travel: http://forum.airsoftaustria.com/showthread.php?t=39217 Smoother trigger pull and semi-only safety catch: http://forum.airsoftaustria.com/showthread.php?t=39211 Link to post Share on other sites
godwin Posted September 25, 2010 Report Share Posted September 25, 2010 I was ask to post this, also think it could be useful: Realsteal Stuff: There are 2 Companies, which clone the AUG: TPD: http://www.tpdusa.com/categories.php and MSAR: http://www.msarinc.com/STGE4.html - some Versions look very nice, could give an idea for some projects You can use some RS Parts for your AEG (e.g. the barrel folding grip with some grinding) one shop i found here, but im sure you can also ask your local weapon dealer: http://www.pjs-steyraug.com/augusrparts.html Other Shop with some Parts: http://www.steyrarms.com/store/index.php/spare-stocks.html Steyr AUG/A3 SA USA Manual with details about the parts (diagrams): http://www.steyrarms.com/downloads/user-manuals/steyr-auga3-sa-usa-manual/ Other site for ideas and info: http://www.steyr-aug.com/accessories2.htm http://www.glock-waffen-technik.eu/hobbies22.html http://www.steyr-mannlicher.com/behoerdenwaffen/steyr-aug-a3-sf/ http://en.wikipedia.org/wiki/Steyr_AUG RS Forum: http://www.steyrclub.com/vb/index.php Link to post Share on other sites
godwin Posted September 25, 2010 Report Share Posted September 25, 2010 My Barrel Grip is broken, can i use the RS one? Yes, you just have to grind it a little at the top. You can get it from your local weapon store or some online shops like: this one in the USA: http://www.pjs-steyraug.com/augusrparts.html (45 USD) this german one: http://www.teilesatz.de/dts_detail.php?id=112&Chap=2 (36 EUR) Differences between AS-AUG-Barrel Grip and RS Barrel Grip: 5mm longer than TM Grip Much more quality: Marui: 50g, cheap plastic (~ 2-3mm thick), die-cast aluminium Original RS: 102g, massive plastic (~ 6-8mm thick), Steel !!! and feels much better! Here a pic (bad one) left = TM, right = RS Link to post Share on other sites
godwin Posted October 21, 2010 Report Share Posted October 21, 2010 Someone said to me that the Guarder SP120 Full Tune-Up Kit will not fit in an Classic Army A2 AUG. Is he right? I mean V3 Gearbox is V3 Gearbox. Link to post Share on other sites
Hedganian Posted October 22, 2010 Author Report Share Posted October 22, 2010 The AUG's gearbox is slightly different from a standard V3, due to the modifications required for the two-stage trigger instead of the more common fire selector. As far as I know, that's the only difference, and everything else - piston, gears, etc - are the same. Link to post Share on other sites
godwin Posted October 22, 2010 Report Share Posted October 22, 2010 I know, its the FTK for AUG. I mean will it fit in the CA or only in the TM AUG GB? Its build for TM. Something should be different with the cylinderhead. I ordered the set, will post experience here. Link to post Share on other sites
Hedganian Posted October 22, 2010 Author Report Share Posted October 22, 2010 Having used TM, CA and JG AUGs, I can say with a fair degree of confidence that there are no significant differences between them. The vast majority of parts will fit any of the AUGs. CA and the others are all clones of the TM original designs, with some little tweaks here and there. The gearboxes are pretty much identical across the three makes I have experience with. Link to post Share on other sites
Recommended Posts
Archived
This topic is now archived and is closed to further replies.