Jump to content

Pictures Thread, Our own Specific Thread, Read Rules


TheBauer

Recommended Posts

  • Replies 2.3k
  • Created
  • Last Reply
  • 1 month later...

Senor Bear - I feel your pain. Nothing quite like "helpful" advice and support fire from other people... Still, you got your mark in the end. 

I think the hit on Elliot (by the fuel dump) might actually have been a miss and ricochet - you can hear it bounce off the drums fractionally before he calls.

 

Still, good stuff. Watching these always makes me want to dig mine out (but I find the limits at CS these days to be... uh... limiting.) :)

Link to post
Share on other sites
  • 1 month later...

Got myself stupid enough to buy this.

 

the Well MB4411D

v73vp1.jpg

it works like a TM aws L96, but the mag is different.

It's a PITA to but together (it is Well for a reason)

It has a nozzle restrictor making it shoot 250fps, without 410fps.

But surprisingly quite accurate OTB.

Link to post
Share on other sites
  • 2 weeks later...
  • 1 month later...

31ig.jpg

 

Tokyo Marui VSR-10 G-Spec

Internal
PDI Palsonite Cylinder SET /HD
PDI New Trigger2 + Piston End
PDI SPR 380 %
PDI G-SPEC Barrel Spacer inner Dia.8.55mm
PDI Bedding Pillar
PDI CS End Cap
PDI HOP UP Chamber Ver.2
PDI W Hold Chamber Packing
PDI M.R.B
PDI PDI 6.01 Inner Barrel 430mm

External
Harris Bibod
Strike Systems Scope, 3,5-10 x 50E, advanced
Element EX309 30mm Scope mount Top Rail
Micro Red Dot
Rifle Stock Cartridge Holder
.223 Remington VMax dummy rounds

Link to post
Share on other sites
  • 1 month later...
  • 4 months later...

My KJW M700 Takedown...it's fairly new to me, got rid of my old favorite spring rifles (SP M40XB and CA M24) and stepped into gas...next on the list is replica leupold M3 scope with low/mid mounts, then freshen up the paintjob including the bipod/scope.

 

1_zps514e4fdb.jpg

3_zpse95ad2fb.jpg

2_zpsee00d4ba.jpg

 

I've done a few simple reliability/efficiency mods to it. After I'm finished accessorizing it I will be working on the accuracy/range. 

Link to post
Share on other sites

Bostitch, I highly recommend the VSR hop-up system for your rifle, I use it in mine and improves the accuracy so much, combine this with a tight bore barrel, and the results are very impressive.

I believe it already has a VSR bucking, a madbull accelerator, however it's pretty rough on the inside so it will be getting replaced. Also the PO used a cut section of a hex wrench as the nub. I replaced that with a pen ink tube, but obviously I want to replace the entire setup with fresh parts and go with a nice 6.03 TBB. I already did some DIY efficiecny mods so it is shooting decent as is, but definitely could use more work in the hopup/accuracy section. 

Link to post
Share on other sites
  • 2 weeks later...
  • 3 weeks later...

I think I will just drop these pics here: My MZ APS-2 #1

 

gallery_21681_2029_42325.jpg
gallery_21681_2029_47383.jpg

 

MZ APS-2

PDI Outer Barrel

PDI Barrel Cap

PDI Barrel Spacer

PDI Receiver

PDI VC Cylinder Set

PDI 180% Spring

PDI v-Trigger ( Original Trigger during photo shoot )

PDI Chamber

PDI 04 Inner Barrel

PDI W-Hold Chamber Packing

Guarder Cocking Handle

Laylax Mount Rail

Unknown Scope & Mount Rings bought off the streets ( subject to change )

 

 

McNett camo form in Multicam

Some worn out mesh fabric in OD

SKD BALS Mk-2, Gen 2 in Multicam

BLACKHAWK SPORTSTER™ PIVOT BIPOD

Link to post
Share on other sites
  • 2 weeks later...

Archived

This topic is now archived and is closed to further replies.

×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and the use of session cookies.