Kunlun Posted December 24, 2011 Report Share Posted December 24, 2011 I got a Magpul PTS MOE stock on mine so every AEG stock should fit? Also got the enhanced buttpad with it Quote Link to post Share on other sites
weekenny Posted December 24, 2011 Report Share Posted December 24, 2011 Yeah any AEG stock will work. Quote Link to post Share on other sites
akiraspeedstar Posted December 24, 2011 Report Share Posted December 24, 2011 (edited) Any AEG stock will fit, though some will require modifications, for example Anakchans Magpul stock where he had to machine his buffer tube. Edited December 24, 2011 by akiraspeedstar Quote Link to post Share on other sites
Hatchet Posted December 25, 2011 Report Share Posted December 25, 2011 Unbelievably I have actually managed to fix mine. Eagle6 bits turned up in a couple of days despite being Christmas, so not bad. As mentioned earlier, the sector gear had broken a tooth, which had then stayed where it broke in the spur gear and caused the jam on the next cycle - which ended up blowing the fuse as well. Then I sheared off the rear power cables when trying to unscrew the stock pipe. Oh, and one of the bearings had shattered too. Replaced bearings with Prometheus ones - I found using a gas valve tool to apply pressure worked quite well, no hammer required. Replaced original gears with Lonex ones. Much bigger tappet plate pickup on the sector gear, generally look better. Disassembled, unsoldered and rewired trigger switch. Made up new motor spade connector for black terminal. Correctly reassembled tappet plate (first time through the notch was off making the nozzle point at an upward angle) Bought a vice in order to unscrew locking ring from stock tube. Unsoldered and rewired rear rail pickup connectors. Replaced fuse. Put back together. Gun still fires (motor height needed a lot of adjustment initially) and bolt lock still works! We shall see if it stays that way after the next skirmish... Quote Link to post Share on other sites
druid799 Posted December 25, 2011 Report Share Posted December 25, 2011 (edited) Unbelievably I have actually managed to fix mine. Put back together. Gun still fires (motor height needed a lot of adjustment initially) and bolt lock still works! We shall see if it stays that way after the next skirmish... And did you sit there with a smug look on you face ? And did you have a warm fuzzy feeling in the sub cockle area of your body ? I hope you did ! Edited December 25, 2011 by druid799 Quote Link to post Share on other sites
elanaiba Posted December 26, 2011 Report Share Posted December 26, 2011 http://www.hyperdouraku.com/custom/p-mag/index.html P-mag covers for your sopmod mag internals?! Quote Link to post Share on other sites
arne71 Posted December 26, 2011 Report Share Posted December 26, 2011 Can we have a proper translation of that one please? Quote Link to post Share on other sites
TheFull9 Posted December 26, 2011 Report Share Posted December 26, 2011 ~70g per magazine is a rather nice weight saving it has to be said. Quote Link to post Share on other sites
akiraspeedstar Posted December 26, 2011 Report Share Posted December 26, 2011 (edited) Anakchan or GingaNinja, any way you guys could help us out in this situation with the pMag shells? I tried contacting them, hopefully it's possible to place an order. I'd probably end up purchasing at least 7 of those shells if possible. http://www.airgunshop.jp/products/detail.php?product_id=17727 Edited December 26, 2011 by akiraspeedstar Quote Link to post Share on other sites
akiraspeedstar Posted December 26, 2011 Report Share Posted December 26, 2011 (edited) Alright they responded to my email, unfortunately they mentioned that they will not ship any orders internationally. Though they recommended a forwarding company (Tenso) to utilize if I wanted products from them. I attempted to make a account with the airsoft shop and can't figure out how the hell to do it haha, plus the google translations can be a little confusing and probably off at times. Anyways, ended up messaging my friend who's from Japan and visits there a couple times a year on aid with this matter. Hopefully he'll be able to figure out something to get me some shells. Edited December 26, 2011 by akiraspeedstar Quote Link to post Share on other sites
Honzo Posted December 26, 2011 Report Share Posted December 26, 2011 how much would it cost in USD to get one of those pmags?! Must have ! Quote Link to post Share on other sites
akiraspeedstar Posted December 26, 2011 Report Share Posted December 26, 2011 Would be pretty pricey, about $25 a shell O_o Part of me says to just modify real steel pMags, since they're only $14 or less each, though there's a decent amount of work you have to do. Compared to paying $11 or so more a mag and having it ready to go haha. Quote Link to post Share on other sites
weekenny Posted December 26, 2011 Report Share Posted December 26, 2011 (edited) They do look great, I'd be tempted as I only have 4 mags to reshell. No option for real mag shells in the UK. I'd prefer a version without the bullet window though. Edited December 26, 2011 by weekenny Quote Link to post Share on other sites
GingaNinga Posted December 26, 2011 Report Share Posted December 26, 2011 I was tempted but after reading the owners blog ( where he shows how to do the transfer ) I have decided against it. Not interested in doing any mods where you have permanently damage the original mags. You can see that he cuts off the mag tabs and does some filing to get them to fit. You also have to add (buy?) stickers for the mag window. They were originly included as a promotion, but you have to buy them now. The original thread from hyper-doraku also mentioned they were tight on the M4 and needed some filing. Here is the blog post. http://hongkongmania.blog68.fc2.com/blog-entry-164.html Quote Link to post Share on other sites
druid799 Posted December 26, 2011 Report Share Posted December 26, 2011 So basically there sounding less and less like the holy grail of EBB and more like a box of poop to sort for use ? Quote Link to post Share on other sites
akiraspeedstar Posted December 26, 2011 Report Share Posted December 26, 2011 I don't mind the modifications to the internals of the OEM magazines, as it isn't severe and looks like you could if you really wanted to just put some foam if returning it into the OEM shell. Though if it has some issues with fitting into the gun then I have some concern. Reading the translated page is hilarious, as some of it makes absolutely no sense haha. Quote Link to post Share on other sites
Honzo Posted December 26, 2011 Report Share Posted December 26, 2011 Reading the translated page is hilarious, as some of it makes absolutely no sense haha. +1 Quote Link to post Share on other sites
zaimon Posted December 27, 2011 Report Share Posted December 27, 2011 (edited) Step by Step RS PMAG Conversion guide for Tokyo Marui M4A1 Sopmod Magazine credit to Echigoya http://echigoyaworks.militaryblog.jp/e284810.html Following is the step by step process on how we convert a real PMAG magazine to fit into an airsoft AEG specifically the recoil shock series. By using the internals of a Tokyo Marui magazine and months of trial and error we were able to accomplish the task… Mission Impossible? Not in our shop! The Real PMag Remove the bottom cap Then you can discard the spring and the round follower, but keep these three parts, you will need them later on. Mark where you will make the trims, good thing about the magpul there is a line that will help guide you. You will make the cuts a few mm above this line. Also take note where the trim will make and make a higher trim on it as shown where the masking tapes are. Fisrt part cutting of the mag using a vertical machine. Second part cutting. Third part cutting (back side).... To look like this (as shown already fitted with the TM internals) Using a dremmel, try to flatten out the foremost part of internal ribs on the mag as shown (include the internal sides) Now we go the TM Magazine internals We need to turn it as shown below, from the right to the left. Using a vertical machine and a dremmel. Trim the flaps as shown below (from the left to look like on the right Trim the underside of the lip To become like this As shown fitted in the mag Now trim the back part Remove this protruding part (also on the front side - no pic) Use a dremmel to trim the corners on this side (shown by the 2nd arrow) and also on the bottom. The purpose of this is to take the shape of the polygonal shape of the Pmag. Now trim the bottom plate of the mag about 3-5 mm (this will depend on the fitting of the internals when you insert it) Now start assembling everything. Edited December 27, 2011 by zaimon Quote Link to post Share on other sites
akiraspeedstar Posted December 27, 2011 Report Share Posted December 27, 2011 Yeah that's way too much work for me haha Quote Link to post Share on other sites
Kunlun Posted December 27, 2011 Report Share Posted December 27, 2011 Big 2nd! Quote Link to post Share on other sites
arne71 Posted December 27, 2011 Report Share Posted December 27, 2011 Better wait for TM or maybe Laylax to come up with the goods. Quote Link to post Share on other sites
Gunfighters808 Posted December 28, 2011 Author Report Share Posted December 28, 2011 some video goodness of the scar-H. from Echigoya. so who's going to pop for this badboy? as much as I want one, with the Yen the way it is, it's just too expensive for me right now. anyone in Japan on the pre-order lists? let us know how it is. Quote Link to post Share on other sites
akiraspeedstar Posted December 28, 2011 Report Share Posted December 28, 2011 The H is only a little more then a SOPMOD Quote Link to post Share on other sites
druid799 Posted December 28, 2011 Report Share Posted December 28, 2011 Yeah that's way too much work for me haha Yup totally agree , realy well put together guide , but with out access to a proper workshop ? No chance , I'll stick with my TM mags ! Lol Quote Link to post Share on other sites
Kunlun Posted December 29, 2011 Report Share Posted December 29, 2011 I suppose these fit fine on the socom: http://shop.ehobbyasia.com/madbull-daniel-defense-9inch-omega-rail.html ? I want something different than my MOE handguards so I tought I would give myself some Christmas presents I chose this handguard since you can open it which seems very practical for replacing the battery etc Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.