Wingman Report post Posted January 15, 2019 Ok, I found the hole where the screw is supposed to be. But, naturally no screw and the hole is not threaded. However, I checked the Colt Rail Gun slides and they also have the hole but no screw. It appears KWC are now driving a pin from the inside of the slide up into into the sight post through a second hole and it a real tight press fit or glued. Who can figure. Decided to lock tite it down and see if it will hold. Now here is where the KJW system of a screw from the outside top of the sight going into the slide is the better deal. Re-assembled the pistol in the new "new" two tone format and it does look pretty sharp. I have to agree that these KWC's are pretty good, my KJW MEU is a bit better, but only after a boat load of upgraded parts. Thanks for the assist..again! Share this post Link to post Share on other sites
scorch Report post Posted January 15, 2019 That's very similar to mine. Two tone rail gun, threaded barrel, grey magpul grips and x300 light. I'm sure I posted it a while back. Share this post Link to post Share on other sites
Wingman Report post Posted January 16, 2019 I'll have to check it out. I've always loved the look. Share this post Link to post Share on other sites
heroshark Report post Posted February 8, 2019 My TM springer with a few metal gbb parts added and s70 grips with the baby. Colt Junior WE gbb KY Airsoft trademark version with my home made grips. Next to make some 1911 grips. 1 Share this post Link to post Share on other sites
wolfgeorge Report post Posted February 25, 2019 Kimber Warrior, Nova kit on Tokyo Marui 1911 Wolf 3 Share this post Link to post Share on other sites
Got Wood? Report post Posted February 25, 2019 Those grips Share this post Link to post Share on other sites
wolfgeorge Report post Posted February 25, 2019 I was looking for some time for those.. I love them. Wolf Share this post Link to post Share on other sites
wolfgeorge Report post Posted February 28, 2019 Brass Chromeplated Prime Colt 1911 Commemorative WWII European theater Wolf Share this post Link to post Share on other sites
blobface Report post Posted March 6, 2019 Takes out two enemy combatants at the same time, as long as the shooter and the target are both your enemies... Share this post Link to post Share on other sites
renegadecow Report post Posted March 6, 2019 Currently thinking up a 40mm version Share this post Link to post Share on other sites
scorch Report post Posted March 6, 2019 9 hours ago, renegadecow said: Unholy picture 1 1 Share this post Link to post Share on other sites
Ivan le Fou Report post Posted March 7, 2019 That is techno heresy. Share this post Link to post Share on other sites
NonEx Report post Posted March 7, 2019 On 3/6/2019 at 10:03 AM, renegadecow said: some thing Aaaah. my OCD/perfectionism can't handle it 😐 Share this post Link to post Share on other sites
blobface Report post Posted March 7, 2019 If you were a perfectionist you'd know that you're witnessing perfection. 1 Share this post Link to post Share on other sites
NonEx Report post Posted March 7, 2019 OK, I forgot "purist" in my wording. A lot of RCs stuff is kewl and all but it kinda makes me feel nauseous 😛 Share this post Link to post Share on other sites
NonEx Report post Posted March 8, 2019 AW Custom Springfield V10 GBB pistol with custom engraved markings from QRF and hex head grip screws (waiting on torx screws) Also quick FYI while it is possible to make RS Hogue grips fit on this, it was a PITA to get the screw holes and bushings fitted (like, pop out the metal bushings from the original grips, Dremel the sh*t out of them, Dremel out the inside of the grip and hot glue the custom bushings etc. and the grip doesn't really line up properly when installed...) Just a quick preview test shoot with my improved light setup with 6 ring lights instead of my original 3. Fun back story about how this came to be over here: 3 Share this post Link to post Share on other sites
BigAl Report post Posted April 24, 2019 Another little un. Had this Prime SIS Ultra kit in my projects stash for years, finally got around to gettin Negative Airsoft to build it for me on an old WA Kimber Parts gun I had. Was hardest WA Build he's ever done apparently, partly down to old knackered donor gun and partly down to kit. It loos lovely but design is very poor. Where the SIS is cut into slide the remaining metal is way to thin and infact can me flexed with finger tip. Anyway great job Luke thanks a lot. This one will be a safe queen I think. lol 4 Share this post Link to post Share on other sites
quiksilver6184 Report post Posted July 22, 2019 Marui - Series 70 1 Share this post Link to post Share on other sites
Colin_The+Ferret Report post Posted July 23, 2019 Please Marui, do a proper Para Ordnance and release the V10.... 1 Share this post Link to post Share on other sites
Wingman Report post Posted July 24, 2019 Please Marui do a Combat Commander! 2 Share this post Link to post Share on other sites
icolater Report post Posted July 26, 2019 Please mafioso do a proper steel, co2, advanced inner frame and proper quality combat commander. Share this post Link to post Share on other sites
renegadecow Report post Posted September 19, 2019 1 Share this post Link to post Share on other sites
hitmanNo2 Report post Posted September 19, 2019 Disappointingly normal for a renegadecow post heh. Share this post Link to post Share on other sites
castigador Report post Posted September 21, 2019 (edited) Western Arms Kimber 1911 LAPD Metro custom with flashlight Edited September 21, 2019 by castigador 3 Share this post Link to post Share on other sites
