MODDAN Posted August 29, 2009 Report Share Posted August 29, 2009 Yes, I am indeed talking about part No. 78. If the catch is already limp thats odd... remove your spring and have a look if it's of the correct length. If not, you should buy a spare. Quote Link to post Share on other sites
ViciousV10s Posted August 29, 2009 Report Share Posted August 29, 2009 Future Noveske/MUR set up. Â Quote Link to post Share on other sites
alston251 Posted August 29, 2009 Report Share Posted August 29, 2009 Is it a whole upper with an integrated rail? 1 Quote Link to post Share on other sites
julietcharlie Posted August 30, 2009 Report Share Posted August 30, 2009 Is it a whole upper with an integrated rail? Â The monolithic upper is the VIS that MUR is only an upper. Â Quote Link to post Share on other sites
Eliminator Posted August 30, 2009 Report Share Posted August 30, 2009 Small ballistic question: when shooting from my window(at 5-6m from the ground)my BBs start heading the sky after nearly 50-60m. When shooting on the ground will be the trajectory as flat as with a perfectly setted up hop up? Quote Link to post Share on other sites
renegadecow Posted August 30, 2009 Report Share Posted August 30, 2009 If you were using real ammunition, maybe. Air gets less dense the higher it is from sea level and less dense air means less friction against wind, which would mean a faster, more accurate bullet. Â But this is airsoft, and you're talking a mere 5~6m difference, add to that the fact that the WE hop is a bit wonky to begin with. So no, there will hardly be any notable difference. Quote Link to post Share on other sites
somegirls Posted August 30, 2009 Report Share Posted August 30, 2009 Has anyone tried the VLTOR MUR upper reciever from Dytac? Â Redwolf claims it fits the WE. Â http://redwolfairsoft.com/redwolf/airsoft/...il?prodID=27382 Quote Link to post Share on other sites
renegadecow Posted August 31, 2009 Report Share Posted August 31, 2009 Best ask ViciousV10s as the picture he posted (previous page) has the PTW upper mounted on a Socom Gear N4 lower. Quote Link to post Share on other sites
lukvdh Posted August 31, 2009 Report Share Posted August 31, 2009 Question for WETTI: Â Is the "WE SCAR-L CQC Gas BlowBack Rifle (Dark Earth)" on UNCompany.com a "WETTI" version, or a WE? Â (With all this version-talk I don't know what to look for....If there are difference: what are they?) Â Thanks in advance. Â Â P.S. I ordered (again) the WE M4 CO2 conversion set, at yet another shop: "sorry, out of stock, can we sell you something else?".... Â Quote Link to post Share on other sites
BrooklynBorn Posted August 31, 2009 Report Share Posted August 31, 2009 They're the same. WETTI is just the long name for WE now. Â Â Quote Link to post Share on other sites
danielsilva Posted August 31, 2009 Report Share Posted August 31, 2009 Has anyone tried the VLTOR MUR upper reciever from Dytac? Redwolf claims it fits the WE.  http://redwolfairsoft.com/redwolf/airsoft/...il?prodID=27382  Quoting from a famous philosopher ...  do a bit of search on your own please, that has been discussed several times already.  Yes it does fit, it will rattle quit a bit which it seems to be largely fixed by using RATech's Magic Pin.  Yes, I am indeed talking about part No. 78. If the catch is already limp thats odd... remove your spring and have a look if it's of the correct length. If not, you should buy a spare.  Well it seems the spring wasn't the original one that came with gun, i received a v1 but the bolt stop was already changed to the new one, i guess they either tried to fix the problem and failed or the spring that came with it was essentially crappola. I got a substitute and now is working like a charm Quote Link to post Share on other sites
somegirls Posted August 31, 2009 Report Share Posted August 31, 2009 yeah sorry, I saw victories post in the picture thread, and in a hurry, didn't notice he posted here as well. Â Â Quote Link to post Share on other sites
danielsilva Posted August 31, 2009 Report Share Posted August 31, 2009 yeah sorry, I saw victories post in the picture thread, and in a hurry, didn't notice he posted here as well. Â Hen i just had my morning sarcasm on, anyway i am actually interested too ... not in that particular upper but if any upper made for the PTW fits the WE also Quote Link to post Share on other sites
julietcharlie Posted August 31, 2009 Report Share Posted August 31, 2009 If I remember it right, there was a company before that can convert a PTW into a GBBr it was LA Company i believe. I am not sure if they were related to AFC who designed the WE platform. Quote Link to post Share on other sites
alston251 Posted September 1, 2009 Report Share Posted September 1, 2009 (edited) Hey guys incase you haven't read the news. RA-Tech made a adjustable valve for the WE GBB system. Â But they demonstrated on a scar. So i'm not sure if it would work for the M4 too. But after watching the video a few times and thinking a bit i thought it would be fine. Â But i'm not entirely sure. Does anyone know if the rod behind the nossle is same length on the scar and the M4? If so i think it would be compatible. Â Can someone confirm this please. Â Bless RA-Tech. Edited September 1, 2009 by alston251 Quote Link to post Share on other sites
danielsilva Posted September 1, 2009 Report Share Posted September 1, 2009 Hey guys incase you haven't read the news. RA-Tech made a adjustable valve for the WE GBB system. But they demonstrated on a scar. So i'm not sure if it would work for the M4 too. But after watching the video a few times and thinking a bit i thought it would be fine.  But i'm not entirely sure. Does anyone know if the rod behind the nossle is same length on the scar and the M4? If so i think it would be compatible.  Can someone confirm this please.  Bless RA-Tech.  Well that sure is good news, at least we have many options. I ordered a couple of those uni-directional guide rod's from TS-Custom, they should allow to adjust the power but until i actually install one of them can't say for sure. But i would buy one ffrom RATech if someone tries them on the M4. Quote Link to post Share on other sites
alston251 Posted September 1, 2009 Report Share Posted September 1, 2009 Lets hope they don't rip us off first. Quote Link to post Share on other sites
somegirls Posted September 1, 2009 Report Share Posted September 1, 2009 The nozzle is the same but the rod is too short. You'd need to use the original rod. Quote Link to post Share on other sites
alston251 Posted September 1, 2009 Report Share Posted September 1, 2009 But would the threading be too long or short? Could be delt with some sanding though. Â I can't wait until it's released. Quote Link to post Share on other sites
L4byr1nth Posted September 1, 2009 Report Share Posted September 1, 2009 (edited) Ok, so I'm looking to add to my DMR WE M16A3. Â I already have a nice 4x32 ACOG. Â What I need is a small, short bipod, perhaps Harris-type? Â Also, anyone know of an RIS/RAS that will fit an M16A3 nicely? Â Ben. Â EDIT:: If there's no rail system, how would I go about shortening the outer barrel length to M4 size, adding a RIS system, and then cover the rest of the inner barrel with a silencer? Edited September 1, 2009 by L4byr1nth Quote Link to post Share on other sites
Eliminator Posted September 1, 2009 Report Share Posted September 1, 2009 (edited) There is the Dboys M5 RIS, but it needs some work on the front section to fit well. On the other hand, there exists RS RIS for relatively low prices, manufactured by Leapers for example For the bipod, parts4ar15.com sells a nice one for a good price.. Â Here are some pice of my DMR M16A3 Â On these pics you'll be able to see some of the details of the RIS. The scope is the 5th Gen 3-9x50 Red/Green Mil-Dot AO from Leapers. The laser comes from Leapers as well Edited September 1, 2009 by Eliminator Quote Link to post Share on other sites
L4byr1nth Posted September 1, 2009 Report Share Posted September 1, 2009 Since posting, I've discovered a Laylax rail that bolts to the underside of a normal M4/M16 handgrip.  Anyone know if that might fit the WE?  Because then I can just use an RIS bipod, and it'd be much simpler.  Also will something like this;  http://www.ebairsoft.com/knights-type-snip...ock-p-1950.html  and this;  http://www.ebairsoft.com/ar15-quick-releas...ter-p-1987.html  Fit the gun?  Cheers!  Ben. Quote Link to post Share on other sites
somegirls Posted September 1, 2009 Report Share Posted September 1, 2009 Pretty sure the stock will NOT fit the WE or any GBB M4. AEGs don't have a full buffer tube. Quote Link to post Share on other sites
L4byr1nth Posted September 1, 2009 Report Share Posted September 1, 2009 Hmmm... I'm currently looking at adding the following;  LaRue 12" R.I.S. system <<--- Not sure it'll fit  Fab Defense M4 Magwell <<--- Pretty sure it'll fit  Fab Defense Fast Mag Grip <<--- Pretty sure it'll fit (rail mounted)  Madbull KX3 Flash Hider <<--- Not sure if the WE is + or - thread though?  Some kind of R.I.S. mounted bipod?  Ben. Quote Link to post Share on other sites
kojak Posted September 1, 2009 Report Share Posted September 1, 2009 If you are going to RIS up your M16 you might as well get a tacti-cool sniper stock. I'm still on the hunt for the fake UBR myself. Â Am I wrong, or does the lowly AirSplat currently have the lowest price in the U.S. for the CO2 mags? I need several more, so I'm willing to go with the lowest bidder. Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.