Mikhailthejackal Posted August 26, 2012 Report Share Posted August 26, 2012 I must admit i havent, but i did strip it to find it looks well lubed already. Quote Link to post Share on other sites
ChickenWatermelon Posted August 27, 2012 Report Share Posted August 27, 2012 Do it anyway? Not like it's gonna hurt your gun. Quote Link to post Share on other sites
jkpics Posted August 30, 2012 Report Share Posted August 30, 2012 (edited) So today CustomGuns got the first production run of CO2 mag o-rings, they are as good as the v0.2 prototype, we will have a english order option up on http://customguns.dk/ in a few weeks but ATM use info@customguns.dk for non DK orders. Â And http://www.facebook.com/CustomGuns only in Danish so far, but we will start translating important stuff if there is a need. Edited August 30, 2012 by jkpics Quote Link to post Share on other sites
NonEx Posted August 30, 2012 Report Share Posted August 30, 2012 (edited) Stupid question. What is the easiest and safest way to remove and install this seal in the magazines? I remember when I was fixing mine up, it's kind of hard to remove without damaging the part. Â Just emailed them for a price quote for 12 pcs. Â Also LOL at translating IMPOTENT stuff Edited August 30, 2012 by NonEx Quote Link to post Share on other sites
jkpics Posted August 30, 2012 Report Share Posted August 30, 2012 Yeah we suck at engrish, more so late at night. Â To get the inner cylinder of the valve out you need to make a tool, cutting down a 2mm Allen key works great, you need to get into the 2 holes in the sides of the cylinder and pull it out, some are easy and some are hard, don't push to hard into the hole or the mesh will come loose and jam the cylinder. Â If the mesh comes loose just glue it down again. Quote Link to post Share on other sites
NonEx Posted September 1, 2012 Report Share Posted September 1, 2012 They do understand english right? I sent an inquery 3 days ago and no reply. Do I have to write anything special ? Quote Link to post Share on other sites
jkpics Posted September 1, 2012 Report Share Posted September 1, 2012 We are working on it, lots of stuff to do, like setting up a paypal account and getting a handle on shipping, on top of a lot of danish back orders Quote Link to post Share on other sites
NonEx Posted September 1, 2012 Report Share Posted September 1, 2012 OK, thanks. Quote Link to post Share on other sites
GhostWolf Posted September 13, 2012 Report Share Posted September 13, 2012 I own an WE M4 CQBR and im trying to find a rail system for it. Can anyone suggest where I can find one? Quote Link to post Share on other sites
NonEx Posted September 13, 2012 Report Share Posted September 13, 2012 What kind are you looking for? Â The MadBull rails fit, installation wise, but as been mentioned many times their actual rails are slightly fat sometimes. Â Other than that RS rails fit. Quote Link to post Share on other sites
GhostWolf Posted September 14, 2012 Report Share Posted September 14, 2012 Looking for a normal KAC 7" RIS to use with the delta ring. Just wondering which ones of them will fit. Quote Link to post Share on other sites
jkpics Posted September 14, 2012 Report Share Posted September 14, 2012 You are in the US, pick up a used RS KAC rail for nothing you lucky ******* Quote Link to post Share on other sites
GhostWolf Posted September 14, 2012 Report Share Posted September 14, 2012 You are in the US, pick up a used RS KAC rail for nothing you lucky ******* Â Lol no im not im in the UK lol.. Quote Link to post Share on other sites
jkpics Posted September 17, 2012 Report Share Posted September 17, 2012 Â Facebook album showing CG O-rings and the start of a DIY guide. Quote Link to post Share on other sites
tinydata Posted September 23, 2012 Report Share Posted September 23, 2012 I'm looking for a new GBB rifle to use as a CQB primary. Â I've got an AEG for outdoors, so I'm not too concerned with long range accuracy or performance, just durability and reliability. Â Most of the action would indoors during the winter, so I think CO2 would be a must. Can the WE M4 OB reliably handle that with a NPAS tuned to 275 fps w/ .25g or will I need to buy the RAtech steel LPK and bolt? Â Thanks for the help Quote Link to post Share on other sites
Basic-Wedge Posted September 25, 2012 Report Share Posted September 25, 2012 I've never been able to tune a gas rifle that low. With the NPAS wide open, I'd be looking at no less than 325 fps with .25s. YMMV - I'm using full length M16s with TB barrels and other upgrades. Quote Link to post Share on other sites
GhostWolf Posted October 7, 2012 Report Share Posted October 7, 2012 (edited) Well anyone looking for a rail system for the WE M4 I can 100% confirm that the Classic Army 7 inch rail fits and works perfect. Â Â Can anyone recommend a good 100% silocon oil for the WE please thats easily available in the UK? Also has any one got a list of compatible replacement internal parts and where to get them from. Been looking at the RATECH site but im getting confused with all the parts numbers. Also been trying to find a stock tube castle nut wrench but damn there hard to find. Edited October 7, 2012 by GhostWolf Quote Link to post Share on other sites
Reppyboyo Posted October 7, 2012 Report Share Posted October 7, 2012 Go into any hobby shop and buy RC Shock oil. 100% silicone and very cheap. Â Your M4 should of come with a wrench if you bought new. Â As for internal parts, is there anything specific you want? 1 Quote Link to post Share on other sites
GhostWolf Posted October 7, 2012 Report Share Posted October 7, 2012 Bought it second hand but it barely been used, probably only about 200 rounds through it. So no the wrench didnt come with it, which is a shame. Looking to upgrade all the internals to steel, so trigger set, hammer, bolt etc. If I am going to do steel going to make it all the same, don't want the problems of steel parts on soft metal parts. Thanks for the head ups on the gun oil, I will get some of the liquid and spray ordered. Will be looking for some other external upgrades at some point, selector switch, I like using a BAD lever so will be fitting one. Quote Link to post Share on other sites
rvlyssup Posted October 7, 2012 Report Share Posted October 7, 2012 @ GhostWolf, RAT steel is soft. They also require fitting to work properly. CWI Airsoft /BBdragon out of Taiwan sells carbon steel internals. Besides, unless your OEM parts are worn, they are still golden. Â Curious about your CA KAC style rail, those are off spec. The ones I have come across are all the same. Not necessarily in lenght but the rails itself. Quote Link to post Share on other sites
GhostWolf Posted October 7, 2012 Report Share Posted October 7, 2012 (edited) Curious about your CA KAC style rail, those are off spec. The ones I have come across are all the same. Not necessarily in lenght but the rails itself. Â Not sure what you mean. The rail came off a Classic Army M4 and is pretty standard to most KAC rails I have seen, except this has the little tab bits what the gas tube sits in and you can tighten down with a screw. Edited October 7, 2012 by GhostWolf Quote Link to post Share on other sites
rvlyssup Posted October 7, 2012 Report Share Posted October 7, 2012 Intresting... Â I have an SPC that I bought brand new in 05 and the top rail is taller. The sides and bottom rails are undersized so rail covers simply slip off. Only xtms work properly as they are clamp on. I thought mine was a fluke but came across several off both carbines and LE stocked version rifles with the same problems. Â Thanks for clarifying bud... Quote Link to post Share on other sites
Reppyboyo Posted October 7, 2012 Report Share Posted October 7, 2012 There is also the Hephaestus steel cnc trigger set. http://www.airsoftglobal.com/shop/index.php?main_page=product_info&cPath=570_573&products_id=15778 Â Not a clue if it is any good as it is quite new. Â Personally Im not a big user of silicone in my GBBR's. I use it for the O-ring on the nozzle and that is about it. For any metal on metal parts I use Slip2000. Quote Link to post Share on other sites
ewashbrook Posted October 23, 2012 Report Share Posted October 23, 2012 There is also the Hephaestus steel cnc trigger set. http://www.airsoftglobal.com/shop/index.php?main_page=product_info&cPath=570_573&products_id=15778 Â Not a clue if it is any good as it is quite new. Â Personally Im not a big user of silicone in my GBBR's. I use it for the O-ring on the nozzle and that is about it. For any metal on metal parts I use Slip2000. Â Might want to check the link there mate. Quote Link to post Share on other sites
GhostWolf Posted October 27, 2012 Report Share Posted October 27, 2012 Whats a good speedloader to use with the WE Gen 2 mags? Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.