EmptyChambers Posted October 20, 2009 Report Share Posted October 20, 2009 Just a quick question would a TM EG1000 short shaft motor fit the Kac? Nope. Either get a medium, or cut down the shaft of a long motor. Quote Link to post Share on other sites
blazed99 Posted October 20, 2009 Report Share Posted October 20, 2009 Cheers mate Would this one fit? http://shop.ehobbyasia.com/upgrade-part/pa...sg-1-sg552.html Quote Link to post Share on other sites
EmptyChambers Posted October 20, 2009 Report Share Posted October 20, 2009 (edited) Yup, that'll do yah although you may have to remove the small collar on top of the motor. Edited October 20, 2009 by EmptyChambers Quote Link to post Share on other sites
gzus11 Posted October 21, 2009 Report Share Posted October 21, 2009 long shaft motor fits if the grip is replaced. i put on the magpull grip and needed a long shaft motor. Quote Link to post Share on other sites
blazed99 Posted October 21, 2009 Report Share Posted October 21, 2009 Cheers mate will it take a standard M4 grip and long shaft motor then? Quote Link to post Share on other sites
andy jennings Posted October 21, 2009 Report Share Posted October 21, 2009 [i have both the d-boys & the vfc dx version and i will say the vfc version is streets ahead of the dboys version but for a cheep alternative its not bad at all lets face it ive got one as a back up to my vfc version ps why buy vfc mags when the clone mags are good value for money and as good as the vfc ones ive got 10 of um and all work flawlessly why pay £22 for a vfc mag when the clone version is just as good at a cost of £11 its a no brainer Quote Link to post Share on other sites
gzus11 Posted October 21, 2009 Report Share Posted October 21, 2009 id assume all standard m4 mags fit, ive only tried the miad one. one point of note is the ambi selector, passes the top of the grip so for example the psg1 type/moulded with thicker section at the top right will interfere with the selector. ive just had mine all apart to rewire, 16g silicone wires fit nicely inside the gearbox, which is one of the best stock ive seen. 7mm bearings, bearing guide and piston head, vented piston, decent shimm and what seem to be good gears. the spring is also a pleasure to work with, mine is cut back to 328fps and if slips into the gearbox with very little precompression, so no shooting apart on dis/assembly. Quote Link to post Share on other sites
08kecarv Posted October 21, 2009 Report Share Posted October 21, 2009 Didn't someone already fit a systema magnum (long) into the PDW grip? I know they had to use different screws and that it stuck out a millimeter or two but it can be done. Quote Link to post Share on other sites
blazed99 Posted October 21, 2009 Report Share Posted October 21, 2009 Would this one fit ? http://www.ebairsoft.com/standard-pistol-g...ies-p-1540.html Quote Link to post Share on other sites
infected Posted October 21, 2009 Report Share Posted October 21, 2009 Didn't someone already fit a systema magnum (long) into the PDW grip? I know they had to use different screws and that it stuck out a millimeter or two but it can be done. Nope. It's a systema medium. If you go with the systema medium motor you have to use longer screws in the grip as the tower at the top of the motor is slightly larger than the one on the dboys. This keeps the motor from moving high enough in the grip to use the stock screws. You have to use longer screws and the motor base plate sits about 2mm lower than stock. Quote Link to post Share on other sites
gzus11 Posted October 21, 2009 Report Share Posted October 21, 2009 i dont know if i had the same issue, for the miad grip i sanded down the plastic on the end of the motor, so that if fit inside the threads of the height adjuster, so i could set it correctly. it took maybe 0.5mm Quote Link to post Share on other sites
08kecarv Posted November 5, 2009 Report Share Posted November 5, 2009 Quick Questions, Anyone heard of the JM KAC PDW??? Any word on how it compares to the DBOYS? Lastly, is the DBOYS the best of the three PDWs out? http://shop.ehobbyasia.com/aeg/other-aeg/j...ft-aeg-902.html Quote Link to post Share on other sites
infected Posted November 5, 2009 Report Share Posted November 5, 2009 So I opened up a teammate's pdw the other day. It has only seen one day of play and here's what I found. One damaged piston (very worn teeth), and 3 out of the 6 bearings were broken. The gearbox has some great features (easily released AR latch, bolt catch, etc), but the bearings are total garbage. Luckily we found the bearings had fallen apart before any gear damage occurred. Quote Link to post Share on other sites
stewpidbear Posted November 7, 2009 Report Share Posted November 7, 2009 So I opened up a teammate's pdw the other day. It has only seen one day of play and here's what I found. One damaged piston (very worn teeth), and 3 out of the 6 bearings were broken. The gearbox has some great features (easily released AR latch, bolt catch, etc), but the bearings are total garbage. Luckily we found the bearings had fallen apart before any gear damage occurred. Out of interest what voltage of battery was your teammate using in it? Quote Link to post Share on other sites
infected Posted November 8, 2009 Report Share Posted November 8, 2009 Out of interest what voltage of battery was your teammate using in it? 9.6v mini. Quote Link to post Share on other sites
BIn Posted November 8, 2009 Report Share Posted November 8, 2009 is the twin lipo battery pack will fit into the ris? Quote Link to post Share on other sites
Rocko Posted November 16, 2009 Report Share Posted November 16, 2009 nope, ra-tech makes conversation kit. google for it. Quote Link to post Share on other sites
ranger-arg Posted November 18, 2009 Report Share Posted November 18, 2009 he menans conversion kit, here is a vid... there is a kit with barrel, gasblock, lipo and charger, around 120, 150 dollars, dont remeber well right now.. Quote Link to post Share on other sites
farrasdevell Posted November 18, 2009 Report Share Posted November 18, 2009 Used mine for an almost full day on sunday and aside from just being fookin noisy it was an awesome little shooter> i did have to do an almost total rewire after melting the tamya connectors off. am looking at a different motor next. Quote Link to post Share on other sites
ranger-arg Posted November 18, 2009 Report Share Posted November 18, 2009 do u have stock parts and internals? Quote Link to post Share on other sites
farrasdevell Posted November 18, 2009 Report Share Posted November 18, 2009 apart from the wiring yep it is (was) totally stock. I took it apart to clean it and change the spring to an m100. It could do with a total reshim as it is noisy as hell but it is shooting straight and very consistently as is so i am relucant to change anything. I took the breach block to work today and set about chopping it down in the same way RA-Tec do to make thier lipo kit 2 simple cuts with a standard hacksaw. Now i just need to order in a couple of lipos and find someplace to hide the mosfet. This gun is inline to take over as my primary since my vsr decided to go to the wall again. Quote Link to post Share on other sites
gzus11 Posted November 23, 2009 Report Share Posted November 23, 2009 i fit my mosfet motor controller to the left side of the hop unit, so you should be able to get all the space beside the barrell for lithium cells. are you going to slim down the barrell similar to the ra kit? Quote Link to post Share on other sites
08kecarv Posted November 23, 2009 Report Share Posted November 23, 2009 i fit my mosfet motor controller to the left side of the hop unit, so you should be able to get all the space beside the barrell for lithium cells. are you going to slim down the barrell similar to the ra kit? Got any pictures of your fitment and what not gzus? Quote Link to post Share on other sites
mrpugster Posted November 23, 2009 Report Share Posted November 23, 2009 gzus have you had any luck in fitting or finding a lipo in that config? There's a guy in the UK, componentshop.co.uk i think who makes custom LIPO's. Has anyone seen the ACM PWD? There's a really thorough video on youtube but it's all in Russian, I was thinking about getting one of those Russian brides and she could translate for me but worked out more than buying all three versions :-) All I could gleam from the 20 min video was that the ACM looks darker and the uploader likes europop Quote Link to post Share on other sites
gzus11 Posted November 24, 2009 Report Share Posted November 24, 2009 no pictures of the set up actually, i always get carried away with the build and forget to take any more pictures, ill try split it open, and get a shot of my controller next to the hop. i have not really looked for li cells that would fit beside the barrel, it does really tidy up the looks, but i also like the laser peq15 i have to hold small 7.4v li packs. i need to measure the cavity and have a look at li packs that could be broken down to cells. actually was impressed by the chap moding a li screwdriver into a battery grip. that may be my future preferred way. Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.