johnnyj Posted March 8, 2010 Report Share Posted March 8, 2010 just took mine out and looked in the old spare's box got to say i dont know if you will get hold of one :s unless you can get down a very good hardwear store its 9mm across and 5mm deep as its a copy of the vfc an email to them might be on order ? or get some wanted adds up i am sure there are lots of people that swapped over the grips for standard m4 size so they can use the long motors if you do happen to email vfc i am in need of the pin that holds the bolt release Quote Link to post Share on other sites
screamin_weasel Posted March 9, 2010 Report Share Posted March 9, 2010 (edited) couple of questions please : what length inner barrel will fit in the longer outer barrel ? should any specific hop rubber be used, or anything goes ? what type of motor is in this ? (size wise i mean) with the tightbore (long outer barrel length-ish), to get this to 350 FPS, which spring should i drop in ? cheers, im ordering from rsov, so looking at vanaras barrels and springs. looking for something equivalent to "Laylax Prometheus Non-Linear Spring MS100" which will, according to landwarrior airsoft, give out 340-350. Edited March 9, 2010 by screamin_weasel Quote Link to post Share on other sites
infected Posted March 9, 2010 Report Share Posted March 9, 2010 should any specific hop rubber be used, or anything goes ? Most things should fit, the prometheus soft works awesome. what type of motor is in this ? (size wise i mean) Medium. Not many choices for a replacement. Quote Link to post Share on other sites
screamin_weasel Posted March 14, 2010 Report Share Posted March 14, 2010 is it possible to run the wires to the grip backwards and out through the hole in th rear of the reciever ? i want to run the wires out out the back and have a 1 point battery sling hooked to the QD mount behind the selector. Quote Link to post Share on other sites
dynamic_e Posted March 15, 2010 Report Share Posted March 15, 2010 Any opinions on the chicom KAC PDW midcaps? Quote Link to post Share on other sites
johnnyj Posted March 15, 2010 Report Share Posted March 15, 2010 just had a quick look at my pdw the hole at the back is in line with the gearbox exit hole for the wiring so yes it can be done easy Quote Link to post Share on other sites
screamin_weasel Posted March 15, 2010 Report Share Posted March 15, 2010 good times. peq can kiss my *albartroth* Quote Link to post Share on other sites
gzus11 Posted March 25, 2010 Report Share Posted March 25, 2010 finally stripped it down again before taking it out this weekend. took a few photos of the motor controll placing as promised. the smaller trigger wires need shortened to tidy it up a little but there is plenty space beside the hop unit. the hardest part was threading the front battery wires back past the gas block, and reconnectingt the bullets on assembly. Quote Link to post Share on other sites
dynamic_e Posted March 26, 2010 Report Share Posted March 26, 2010 Whoa, thats awesome! A/B fet or just a straightforward mosfet? Quote Link to post Share on other sites
gzus11 Posted March 26, 2010 Report Share Posted March 26, 2010 (edited) a full switching and braking unit. Edited March 26, 2010 by gzus11 Quote Link to post Share on other sites
beretta Posted March 26, 2010 Report Share Posted March 26, 2010 Nice job, what motor are you using? or did you bother changing it? i find the dboys motor very slow and noisy. Quote Link to post Share on other sites
gzus11 Posted April 6, 2010 Report Share Posted April 6, 2010 changed the grip for a miad one so needed a long motor, think its a g&p 120 or 160 i found the original motor pretty good, only changed it as i changed the grip. Quote Link to post Share on other sites
tinydata Posted May 14, 2010 Report Share Posted May 14, 2010 Does anyone know if the JM PDW is just a rebranded Dboys? Thanks Quote Link to post Share on other sites
beretta Posted May 14, 2010 Report Share Posted May 14, 2010 no its a different gun altogether, A little shinier and a lot lighter, overall i think its a little better than the Dboys, but theres no much in it. Quote Link to post Share on other sites
tinydata Posted May 15, 2010 Report Share Posted May 15, 2010 Dboys are all out of stock so I ordered a JM PDW , 3 90rd mags and a 11.1v lipo. Review will be up soon after it gets here. Anybody got a Dboys to sell? Quote Link to post Share on other sites
yusanai Posted June 4, 2010 Report Share Posted June 4, 2010 Hello lads and lasses, I'm in a wee bit of problem, I lost the locking pin that keeps stock folded on the side pin. Any one mind telling me where I can find a replacement (I googled with no success) or maybe posting some pics with the whole thingie maybe I can cobble something toghether ? Quote Link to post Share on other sites
Luis21 Posted July 3, 2010 Report Share Posted July 3, 2010 Hey guys, how's the folding front sight on the gun? Solid? I know the gun itself is good but the front sight.... Wobble? Adjust for elevation? Thanks, -Luis Quote Link to post Share on other sites
l96ninja Posted July 3, 2010 Report Share Posted July 3, 2010 Has anyone compared the JM PDW to the D-Boys version? I'm looking for a KAC PDW replica, but want the best for under $200. Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.