bbstriker Posted April 22, 2012 Report Share Posted April 22, 2012 OK. Thanks for that. I'll take another look then Seems to be a (good) low price. Quote Link to post Share on other sites
snake_pliskin Posted April 25, 2012 Report Share Posted April 25, 2012 (edited) OK. So what issue and/ or problem does this Wii thing address? What improvement does it provide? All genuine questions. I'm up for after market improvements. from my experience that kit was a waste of time and money, it doesn't work. that hop chamber will give you inconsistent hop, while the air seal nozzle's o-ring is cr@p, it doesn't seal at all. grabbed this instead. it simply works. http://airsoftpro.cz/eshop/product_info.php?products_id=1522 EDIT: Sorry, I was talking about the Wii-Tech Hop Chamber and Air Nozzle Kit. Edited April 25, 2012 by snake_pliskin Quote Link to post Share on other sites
jimmythetool Posted April 25, 2012 Report Share Posted April 25, 2012 For anyone yet to see the new GBB conversion kit: http://shop.ehobbyasia.com/beta-project-by-pts-masada-gbb-conversion-kit-black.html Definitely something I'd be interested in, but £150 plus cost of new mags isn't too appealing. Interested to see what the early reviews say... Quote Link to post Share on other sites
V3RTIGO Posted April 26, 2012 Report Share Posted April 26, 2012 from my experience that kit was a waste of time and money, it doesn't work. that hop chamber will give you inconsistent hop, while the air seal nozzle's o-ring is cr@p, it doesn't seal at all. grabbed this instead. it simply works. http://airsoftpro.cz/eshop/product_info.php?products_id=1522 EDIT: Sorry, I was talking about the Wii-Tech Hop Chamber and Air Nozzle Kit. Why does it give inconsistent hop? Quote Link to post Share on other sites
TheFull9 Posted April 26, 2012 Report Share Posted April 26, 2012 Quick one, and I apologise if this has been over with the earlier technical discussion, but my ACR is being a bit funny. Works nicely when it fires, but every so often (at fairly random time intervals) it just goes stone dead and for some reason just smacking it really hard on the side of the mag well brings it back. Dodgy bit of soldering in there somewhere? I've had the gearbox out and what I could see all looked fine. Quote Link to post Share on other sites
Megalomaniac Posted April 26, 2012 Report Share Posted April 26, 2012 Microswitch issue most likely, it is the Achilles' Heel of the design. Quote Link to post Share on other sites
snake_pliskin Posted April 26, 2012 Report Share Posted April 26, 2012 (edited) Why does it give inconsistent hop? i find the stock hop-up chamber more consistent compared to the wii-tech hop-chamber. we all know that disassembling the part were the hop chamber sits is PITA. i think the wii-tech's poor o-ring installed on its air nozzle contributes to that. from my experience, the air nozzle from AirsoftPro and the stock hop chamber works very well, it gives me a stable and consistent hop. at least, in my case, the wii-tech hop chamber and air nozzle kit just doesn’t works for me. Edited April 26, 2012 by snake_pliskin Quote Link to post Share on other sites
Orlando Posted April 26, 2012 Report Share Posted April 26, 2012 Hi! This my ACR. First test: Wii -Tech hop-up chamber & Systema Energy hop-up bucking(new&cold).I started with maximum hop-up. I use G&G 0.25g BB.(without sigshts,no fix position) Weather is cold and windy http://airsoftbuilds.com/weapon.php?id=1278 Quote Link to post Share on other sites
ODST_NE0 Posted April 26, 2012 Report Share Posted April 26, 2012 Really like the Black and Tan Orlando, kinda makes me want a Guinness right now. Are you running debounce code on your mosfet? Quote Link to post Share on other sites
TheFull9 Posted April 26, 2012 Report Share Posted April 26, 2012 Microswitch issue most likely, it is the Achilles' Heel of the design. Alright, cheers. What do I need, a new one? Or just to solder it's connections more securely? Quote Link to post Share on other sites
lionel_oger Posted April 27, 2012 Report Share Posted April 27, 2012 Hello Everyone. I received my GBBR conversion kit today and quickly fitted everything. The magnet will stick to the sear, trigger, hammer, bolt spring guide bolt lock and the piece of the charging handle in contact with the bolt. The bolt does not seem to be in steel. Hop up chamber in metal but no reaction of the magnet there. The trigger position seems strange as is the contact of the sear and the hammer. the contact zone is too tiny and barely hold the hammer. The trigger seems too far aft a bit like the trigger of a glock with it's firing pin released. The biiiig problem is that the bolt is too wide to fit the upper. There is absolutely no way it will slide in there. It's not my upper as it align flush with the lower(aeg and gbb lower both tested) as well, the upper has two raised lips in the back to make sure the lower is properly aligned. SO, a lot of sanding is to be done on the bolt. it has 4 little tabson the bolt sides that were putted there to avoid play I guess. I had to sand them flush and give a few strokes of sanding stick to the 2 gutters on top of the bolt. Now it finally cycle correctly. G&P Pmags have A LOT of play leading to inconsistent performance, misfeeds and a lot of gaz release. Have to glue plastic card on the magwell to get that fixed. As well we need to find a way to stop the play of the trigger assy block in the lower as I guess it's also play part in the inconsistency. To resume; Not a plug and play mod, Lot to be done to get a properly working gun, Some work to expect. On the bright side, the hop up seems to have plenty of hop! and build quality of the parts is great. More later Cheers Lio Quote Link to post Share on other sites
Orlando Posted April 27, 2012 Report Share Posted April 27, 2012 I install the WII TECH hop up adjuster kit: Much better with adjusting kit & H nub! http://www.facebook.com/photo.php?fbid=426132664063885&set=a.424341020909716.107897.244617215548765&type=3&theater http://www.facebook.com/photo.php?fbid=426138360729982&set=a.424341020909716.107897.244617215548765&type=3&theater http://www.facebook.com/photo.php?fbid=426352800708538&set=a.424341020909716.107897.244617215548765&type=3&theater http://www.facebook.com/photo.php?fbid=426132974063854&set=a.424341020909716.107897.244617215548765&type=3&theater http://www.facebook.com/photo.php?fbid=426136750730143&set=a.424341020909716.107897.244617215548765&type=3&theater Quote Link to post Share on other sites
bbstriker Posted April 27, 2012 Report Share Posted April 27, 2012 (edited) Oriando. Your videos showing you firing out of a window into a public place is reckless and irresponsible. It conveys a very bad image of the sport. The last thing the sport needs is your videos spreading around giving the impression that airsofters are gun totting weirdoes firing weapons into public places. Seriously mate, find a better place like a skirmish field. Edited April 27, 2012 by bbstriker Quote Link to post Share on other sites
ODST_NE0 Posted April 28, 2012 Report Share Posted April 28, 2012 Just installed an Extreme Fire Cheetah MOSFET w/ the SW-UCM and proud to say that there are NO bouncing issues with the micro switch. Highly recommend it. I did have to replace the positive wire to the motor with one a wire with a thinner insulation so that I was able to route it to the front (routed through the normal gearbox hole, then over the top of the microswitch, then out the hole in the front, I can post pics on request.) Quote Link to post Share on other sites
Orlando Posted April 28, 2012 Report Share Posted April 28, 2012 (edited) the ruined house. nobody lives there. there are not peoples and a street there. abandoned house. to play there CQB thanks Edited April 28, 2012 by Orlando Quote Link to post Share on other sites
bbstriker Posted April 28, 2012 Report Share Posted April 28, 2012 the ruined house. nobody lives there. there are not peoples and a street there. abandoned house. to play there CQB thanks I appreciate what you say but that is not the point. It is still a public place and looks very bad seeing someone firing an airsoft weapon out across a public place. It only takes an over lubricated hop to cause a bb to arc down and hit someone. It's very bad and the very least you should do is not publicise it. Quote Link to post Share on other sites
Orlando Posted April 28, 2012 Report Share Posted April 28, 2012 Did you not read it on youtube? ? The video is not public! Quote Link to post Share on other sites
Misfit Posted April 28, 2012 Report Share Posted April 28, 2012 Hi. It's obviously not recommended to go firing in public but at the very least, please don't post videos of it here. Last thing anybody wants is someone doing the same and having an ARU round. Quote Link to post Share on other sites
Orlando Posted April 28, 2012 Report Share Posted April 28, 2012 man. this dead CQB city. official battlefield. Does he not understand it? Quote Link to post Share on other sites
ODST_NE0 Posted April 28, 2012 Report Share Posted April 28, 2012 man. this dead CQB city. official battlefield. Does he not understand it? If the video is at an official field with rules and regulations, then you need to mention it as an actual playing field, so people don't get the wrong impression. If it is just an "abandoned" area (which is still considered to be public), it is going to be criticized as it displays a bad image. I never got to see any of the vids due net speed connections, so I can't really comment on what it looks like. Additionally this is going off topic, so some of this might better be dealt through PM. Quote Link to post Share on other sites
V3RTIGO Posted April 28, 2012 Report Share Posted April 28, 2012 Just installed an Extreme Fire Cheetah MOSFET w/ the SW-UCM and proud to say that there are NO bouncing issues with the micro switch. Highly recommend it. I did have to replace the positive wire to the motor with one a wire with a thinner insulation so that I was able to route it to the front (routed through the normal gearbox hole, then over the top of the microswitch, then out the hole in the front, I can post pics on request.) Glad to hear it, thanks! never found a person who installed it in a Masada and posted it. I want to buy the SW-UCM too with AB MOSFET. What do you people say about the AVOCADO active breaking MOSFET? Link: http://shop.ehobbyasia.com/avocado-burst-avocado-programmable-mosfet-device-for-aeg-1-12-30-rounds.html Quote Link to post Share on other sites
ODST_NE0 Posted April 28, 2012 Report Share Posted April 28, 2012 The AVOCADA looks no to be a true MOSFET per say, as the power to the motor goes through the microswitch. Other MOSFET direct power away from the switch or completely take it out of the switch, preventing stress. Personally I would go with the MOSFET with 4 wires to protect the microswitch as much as possible. Quote Link to post Share on other sites
V3RTIGO Posted April 28, 2012 Report Share Posted April 28, 2012 What about this: http://extreme-fire.com/2011-SW-AB-LONG.html I need a basic yet reliable AB MOSFET. Quote Link to post Share on other sites
ODST_NE0 Posted April 28, 2012 Report Share Posted April 28, 2012 Honestly I would go with it, if you are planning to UCM from him, might as well get your money's worth from the shipping. Extreme Fire makes excellent MOSFET, yet the only MOSFET that has ever given my trouble was an Infected Armory one, and by trouble, it just smoked up and burned out. Quote Link to post Share on other sites
Orlando Posted April 29, 2012 Report Share Posted April 29, 2012 I did it today in the morning shooting test. I distributed the distance punctually. Wii tech hop up chamber & adjustor kit & H nub, Systema hop up bucking. I use G&G 0.28 BB's. Maximum range 80-82 meters! ( 262-269ft). Until 70 metres(229ft) very accurate. moves very directly. Video coming soon I recommend it the complete wii tech kit for everybody. who the long range likes it and the accuracy. Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.