1st Commando Posted November 21, 2010 Report Share Posted November 21, 2010 that sounds like over hop ,are you sure you are adjusting the right way ? Quote Link to post Share on other sites
bbstriker Posted November 21, 2010 Report Share Posted November 21, 2010 Does anyone have alink to the NPAS kit for this gun. I got m G39C on Friday. It's the best GBB I've ever used. Amazing- even in cold weather circa 5 centigrade! Quote Link to post Share on other sites
AnakChan Posted November 21, 2010 Report Share Posted November 21, 2010 You only need to click back one page, mate. Quote Link to post Share on other sites
Break100 Posted November 22, 2010 Report Share Posted November 22, 2010 that sounds like over hop ,are you sure you are adjusting the right way ? I tried several time and the result still the same. Dialed to minimum hop the bb rolled out at the second shot and i must recharge it. If i dialed to the left/increase just for a bit, with 0.2 it will over hop. So does anyone here also experience this? I almost sure that all WE gbbrs have this curse. Quote Link to post Share on other sites
mnmc10 Posted November 22, 2010 Report Share Posted November 22, 2010 (edited) "I almost sure that all WE gbbrs have this curse." on the old ball bearing type hop yes. but not with the marui type hop rubber.... i have a gut feeling that the round thing inside the hop assembly was cut a tad too long thus jamming in the slot. it looks like a big oring that they cut to size by hand. cause on my pdw that part was not cut squared. see if you can replace it with an insulation from a copper wire or if it fits you can try if the one used in AEGs will work. Edited November 22, 2010 by mnmc10 Quote Link to post Share on other sites
1st Commando Posted November 22, 2010 Report Share Posted November 22, 2010 I can confirm that G&P front kit for aegs fit and work fine ! Stock rubber from aeg fits fine too meaning I have been able to do away with the squared edges Quote Link to post Share on other sites
bbstriker Posted November 22, 2010 Report Share Posted November 22, 2010 (edited) Last night I fired off a whole mag at 2 celcius. I left the mag for 2 hours in my fridge which shows 2 celcius temp. Took it out and fired off a 30 round mix of single and full auto. I'm gobsmacked by the performance of this rifle! Does anyone know if WE Airsoft plan on Co2 mags for the G39C? If they do release Co2 mags for this baby then sub-zero Celcius skirmishing with a GBB rifle is here. Edited November 22, 2010 by bbstriker Quote Link to post Share on other sites
1st Commando Posted November 22, 2010 Report Share Posted November 22, 2010 To be honest having owned pretty much all the WE range plus some other makes I will never ever put a CO2 mag in my guns ! Quote Link to post Share on other sites
bbstriker Posted November 22, 2010 Report Share Posted November 22, 2010 I can confirm that G&P front kit for aegs fit and work fine ! Stock rubber from aeg fits fine too meaning I have been able to do away with the squared edges Thanks for that. Do you know which RIS handguard may fit on the G39C? I rather fancy the idea of a G36C RIS handguard and a silencer. Quote Link to post Share on other sites
Reppyboyo Posted November 22, 2010 Report Share Posted November 22, 2010 Skirmished mine yesterday. No more than 5c, worked fine all day. Quote Link to post Share on other sites
LordElpus Posted November 22, 2010 Report Share Posted November 22, 2010 Last night I fired off a whole mag at 2 celcius. I left the mag for 2 hours in my fridge which shows 2 celcius temp. Took it out and fired off a 30 round mix of single and full auto. I'm gobsmacked by the performance of this rifle! Does anyone know if WE Airsoft plan on Co2 mags for the G39C? If they do release Co2 mags for this baby then sub-zero Celcius skirmishing with a GBB rifle is here. Yes they are making a Co2 mag but i do not know the timeframe for it. Had the too brief chance to play with one Sat night. Fired of a mag doing burst 3 half second burst 3 (more or less how i tend to use FA) and it had no problems at all considering it was half past midnight and the mag had been in the car all the way from Leicester buried in kit. Quote Link to post Share on other sites
rvp69 Posted November 25, 2010 Report Share Posted November 25, 2010 what about the HOP ,is the gun shooting straight? Quote Link to post Share on other sites
Break100 Posted November 25, 2010 Report Share Posted November 25, 2010 what about the HOP ,is the gun shooting straight? mine is not. but someone here said that it works fine with firefly hard bucking Quote Link to post Share on other sites
tangloppen Posted November 25, 2010 Report Share Posted November 25, 2010 Commando, explain please Quote Link to post Share on other sites
1st Commando Posted November 25, 2010 Report Share Posted November 25, 2010 explain what sorry ?# Quote Link to post Share on other sites
Reppyboyo Posted November 25, 2010 Report Share Posted November 25, 2010 what about the HOP ,is the gun shooting straight? Stock rubber is adequate for CQB, overhops .2`s but works fine with .25`s. Used a Firefly hard, groupings were improved as was consistency. Now using a Firefly soft, overhops .25`s with the hop off but the accuracy and range is excellent. Got a Prommy air seal rubber to try next. Quote Link to post Share on other sites
LordElpus Posted November 25, 2010 Report Share Posted November 25, 2010 So using .28s with a Firefly soft would be just about perfect? Quote Link to post Share on other sites
Reppyboyo Posted November 25, 2010 Report Share Posted November 25, 2010 Probably. The overhop gave me great range with .25`s. With .28`s it should flatten it out and hopefully keep the range. 1 Quote Link to post Share on other sites
LordElpus Posted November 25, 2010 Report Share Posted November 25, 2010 cheers mate, i'll keep that in mind for when i get mine. Where did you source your firefly rubbers from? Quote Link to post Share on other sites
Reppyboyo Posted November 25, 2010 Report Share Posted November 25, 2010 Got both my Firefly`s from Fire Support. About £20. Not cheap for a piece of rubber but hey ho this is airsoft. Prommy Rubber I ordered from ehobby. Quote Link to post Share on other sites
bbstriker Posted November 25, 2010 Report Share Posted November 25, 2010 How easy is it to change hop rubber? Quote Link to post Share on other sites
Reppyboyo Posted November 25, 2010 Report Share Posted November 25, 2010 Couldn't be simpler tbh. Quote Link to post Share on other sites
Break100 Posted November 26, 2010 Report Share Posted November 26, 2010 Stock rubber is adequate for CQB, overhops .2`s but works fine with .25`s. Used a Firefly hard, groupings were improved as was consistency. Now using a Firefly soft, overhops .25`s with the hop off but the accuracy and range is excellent. Got a Prommy air seal rubber to try next. Thanks! this is a very useful information. I wonder if i can get it from WGC. The one that available in my town is rubber from KingArms and no idea whether it's hard or soft rubber. Mine with stock rubber must use 0.3 to flatten the bb flight path. I noticed that the part inside the stock rubber which pressing the bb is not smooth may be due to the cutting process. Quote Link to post Share on other sites
AnakChan Posted November 26, 2010 Report Share Posted November 26, 2010 Hmmm....I found my stock WE39C to overhop even with 0.28g BB's. So FF kurages over hop too? My goal is to use with 0.2g BB's. Quote Link to post Share on other sites
mnmc10 Posted November 26, 2010 Report Share Posted November 26, 2010 can you guys try to replace the cylindrical rubber above the hop rubber into a smaller one? the stock one might be too big causing it to push the hop rubber even in off position. Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.