Jump to content
Sign in to follow this  
AnakChan

Initial Impressions of the TM SCAR-L Recoil Shock AEG System

Recommended Posts

20120420_174140.jpg

 

Got my new fakEOtech sight today. Stuff done to it: deans plugs, lonex next gen aeg metal bushings, shs steel gear set, cut down guarder sp100 spring (shoots 350 fps with .20g bbs), prommy 6.03mm x 341mm tightbore barrel, magpul afg2, magpul ms3 sling. Gun uses a hyperion 7.4v 1900mah 35c lipo. Rof is at 15-16 rps.

  • Like 1

Share this post


Link to post
Share on other sites

Has anyone successfully implemented 3round burst on the scar or the sopmod yet? I was wondering if this was even possible and if so which mosfet did you use?

I have an early version of the burst wizard and I was wondering if i were to hook it up to a next gen gearbox, would it work?

Share this post


Link to post
Share on other sites

Has anyone successfully implemented 3round burst on the scar or the sopmod yet? I was wondering if this was even possible and if so which mosfet did you use?

I have an early version of the burst wizard and I was wondering if i were to hook it up to a next gen gearbox, would it work?

 

Burst wizard works on the next gen AEG's. Ive tried the King Kong version on the Marui Next Gen SCAR-H and M4 SOCOM. I ran it on my SOCOM for a while. There's no room for it in the scar unfortunately. At least not unless you decide to use a 7.4v 1350mah lipo and rewire the gun...I like my 1800mah lipo so burst wizard in the scar is not gonna work for me.

Share this post


Link to post
Share on other sites

Burst wizard works on the next gen AEG's. Ive tried the King Kong version on the Marui Next Gen SCAR-H and M4 SOCOM. I ran it on my SOCOM for a while. There's no room for it in the scar unfortunately. At least not unless you decide to use a 7.4v 1350mah lipo and rewire the gun...I like my 1800mah lipo so burst wizard in the scar is not gonna work for me.

thanks for the quick reply! I was wondering what kind of deminsions do you think would fit along with the burst wizard? IE would this one fit? http://www.hobbyking.com/hobbyking/store/__20422__Turnigy_nano_tech_1300mah_2S_25_50C_Lipo_Pack_USA_Warehouse_.html

Share this post


Link to post
Share on other sites

I'll have to check about that.

 

On a side note...buddy made me a rig for the SCAR-H. Its awesome in terms of build quality but I'd like for the rig so the magazines sat higher. He's stuffed with work so my next rig wont be ready for the next 3 weeks.

 

20120510_143351.jpg

 

I have Kydex inserts holding the magazines in place. He did include bungee cords as well as pull tabs for additional retention.

 

Asked him to have my next rig set up so the mag sat higher like on the pic underneath. The bottom 3/4 inch of the rig is excess material if I moved the wedges up so the magazine sat higher on the rig. No buckles on the chest area as per requested. I don't like how the buckles come into contact with the stock when I brace the gun before shooting.

Share this post


Link to post
Share on other sites

Hi there.

 

My Friend has lost the front lower body receiver pin on his TM Scar H. Where can we find a new one. store, Online...

Links would help.

 

We Looked at the Magpul PTS ACR Pin, could this fit?

 

 

Thank you!

Share this post


Link to post
Share on other sites

Theres no known replacement pins yet. I'm sure FF will release a locking pin for the SCAR. At worst, you can always find metric screws and a nut to keep the upper and lower together.

 

Good luck!

 

20120510_183601.jpg

 

Mags hiked up about a quarter inch. Bottom of the pouched folded some. 3 long weeks of waiting for the proper rig. This will have to do for now.

Share this post


Link to post
Share on other sites

Question for the better informed, as far as compatibility goes for gearbox internals can anyone confirm what SCAR-L parts can be used in the H? I'm assuming gear set is a no brainer, but piston, piston head, etc... Much appreciated, this will help me greatly in making my decision to pick one up since they're finally becoming available in Korea

Share this post


Link to post
Share on other sites

^ that and maybe switching every load bearing part out with Lonex equivalents (I assume the M4 gears work with the SCARs?), change the motor to something torque-y like the Lonex A1 or I think A3 and run a FET in the future (AWS's coming out with next gen FETs soon) and a 11.1v lipo in the stock.

 

Also run a hard bucking with R-Hop installed (or ER if possible) and you should have an accurate SCAR-H EBB out to 300 feet shooting 0.3g or higher :D

Share this post


Link to post
Share on other sites

I have been running hi caps in my scar for a while now but decided to break out the mid caps today, anyway after empting the first magazine I noticed that the bolt lock function has stopped working, as in the gun will dry fire even though the mag is empty.

 

Any ideas?

Share this post


Link to post
Share on other sites

Its either going to be down to the mags or more likely the bolt stop mechanism at the top of the magwell. You will have to pull the gearbox out and check that the bolt mechanism and more imortantly the spring on it is positioned properly and has the correct movement. If it's the mags check that the bolt stop lever on the back of them at the top is moving freely.

Share this post


Link to post
Share on other sites

I just got the rest of the mid caps out and tried 4 of them all on drying firing, I'm pretty sure they use to lock after one pull of trigger but now none of them do. Looks like it may be internal as you suggested. Taking these things apart is not really my thing so may contact Fire Support were I purchased it from.

Share this post


Link to post
Share on other sites

Anyone switched their cocking handle to the other side? I took the allen bolt out the centre of mine thinking that might allow me to do so... turned out not so much. Presuming the receivers need to be split?

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

×

Important Information

By using this site, you agree to our Terms of Use and the use of session cookies.