Jump to content
renegadecow

AK & Variants Picture Thread

Recommended Posts

Everything I've seen in terms of interviews/footage with Jim Fuller seems to indicate a lot of folks are picking up weapons with those blocks. Pretty certain Haley has one/multiple, I've slept since I watched Dynamic Kalash though.

Share this post


Link to post
Share on other sites

I got the idea after watching the Kalash video, as well as Haley's HSP's youtube clip...Tracked down Rifle Dynamic's site, then found the Venom Tactical being the supplier......:D

Share this post


Link to post
Share on other sites

DON'T REVEAL OUR SECRET!!!! :P

 

I'm currently building Haley's HSP Kalash, however the TM outer barrel is a bit too thick for the gas block. Did you have that problem with your GHK?

 

EDIT: http://www.airsoft2day.com/news/982-rifle-dynamics-ak-to-be-released.html

 

GOD. DAMN. IT. TO. HELL.

Edited by aznriptide859

Share this post


Link to post
Share on other sites

I had to drill my Bolton out a slight bit(whatever size drill I happen to find at work that comes the closest...) before I can use it...

 

Also helps when you install, jam a flat head screw driver into that gap, slide the gas block on, and remove the screw driver...

Share this post


Link to post
Share on other sites

DON'T REVEAL OUR SECRET!!!! :P

 

I'm currently building Haley's HSP Kalash, however the TM outer barrel is a bit too thick for the gas block. Did you have that problem with your GHK?

 

EDIT: http://www.airsoft2day.com/news/982-rifle-dynamics-ak-to-be-released.html

 

GOD. DAMN. IT. TO. HELL.

 

Looks cool, not too hard to imitate (except for the gas block), I just hope they dont over price an ACM AK (most probably Cyma) with a couple of fancy bits

Share this post


Link to post
Share on other sites

If its cyma it may be more than sucessful if they sell it with average power levels (350FPS) and a decent bucking, although the only thing I expect from this gun is cyma to release the gas block separatedly at any time so any mildly tactic00led AK fan can build his own at a fraction of the cost.

 

Personally, Im happy just with the ultimak and an m4 flash hider

 

Hurry up airsoft systems, release that M4 so you can release an AK105 too!!!!!! :lol:

Share this post


Link to post
Share on other sites

DSCF1439Medium.jpg

 

2012 VFC AKM

- Guarder infinate torque motor

- Guarder 6.02 tightbore inner barrel

- Guarder 120 spring

- A+ hop rubber

- 11.1V lipo

- LCT bakelite pistol grip

- MAG AKM midcaps (refinished in "fakelite" staining)

- Dboys GP-25 launcher

- Custom Vanaras steel PBS-1 silencer converted into a tracer unit

- Real Russian sling

- Russian canvas drop bag

Share this post


Link to post
Share on other sites

I have tested the rifle before i installed the tightbore and i didn't notice much change. Although when installing the new 6.02 barrel i noticed while looking down the chamber, that the hopup rubber has created a very "R-hop" looking flat contact point right across the top of the barrel. So i do have high hopes for the A+ rubber.

 

I will hopefully get to test it out soon, my next issue is bb's weight as i usually use .28 and will wait and see if i need something heavier... and then there's my never ending quest to find tracer bb's heavier than .25g...

Share this post


Link to post
Share on other sites

Thanks for the input mate, I read some good things and some bad things about those buckings, so just wanted to know if it was better than making my own flat hop mods

Share this post


Link to post
Share on other sites

Awesome gun Delta, I was actually about to unfollow this thread due to there being more {Awsome} on the last few pages than actual AK stuff.But, the PBS-01 and GP25 were refreshing.

Edited by cazboab

Share this post


Link to post
Share on other sites

Awesome gun Delta, I was actually about to unfollow this thread due to there being more {Awsome} on the last few pages than actual AK stuff.But, the PBS-01 and GP25 were refreshing.

 

For those interested the PBS-1 tracer mod is very easy. I removed the outer shell of a JG full auto tracer unit and cut down the on/off switch, from there it slipped perfectly into the PBS-1. I used 4 of the original foam inserts to space the tracer unit flush with the base of the silencer Screw it all together and youre all done, a tracer unit you can use on an AK without having to use a modern looking stock tracer unit.

Share this post


Link to post
Share on other sites

20121004_002830.jpg

 

 

Not quite done yet. My WE AK PMC to AKM conversion. I Added:

 

LCT Gas Tube (requires modding to fit)

RA Tech GHK AKM Wood kit set (Wood stock and hand guard had to be modded. Pistol Grip has yet to fit properly)

Element Steel rear sight

 

 

+ a few rounds of steel cased 7.62X39mm for good measure

Edited by 3vi1-D4n
  • Like 1

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×

Important Information

By using this site, you agree to our Terms of Use and the use of session cookies.