Marco-White Posted June 27, 2014 Report Share Posted June 27, 2014 The country's laws forbids mailing/shipping replicas. ie, every replica sold in Belgium is sold in a brick and mortar shop. You could mail them and see if there are workarounds but I don't know if that would succeed. Thanks again Vortix, your suggestion worked Kind regards Marco Quote Link to post Share on other sites
deadwood83 Posted June 28, 2014 Report Share Posted June 28, 2014 So the stock A&K electronics have a nifty feature that fails to get mentioned. Three round burst. I don't know what I did, but now my auto is a three round burst. Quote Link to post Share on other sites
Lyng Posted June 28, 2014 Report Share Posted June 28, 2014 Ive had about 5 a&k ptw apart the last short time, 3 with broken gears and two with broken electronics. All ive seen have had extremely much resistance in the gearbox so its deffenently an issue. Problem is sungear as earlyer stated and it could be fixed to run more free Quote Link to post Share on other sites
Vortix Posted June 28, 2014 Report Share Posted June 28, 2014 Thanks again Vortix, your suggestion worked Kind regards Marco Good to hear! Quote Link to post Share on other sites
rwoodcock01 Posted June 28, 2014 Report Share Posted June 28, 2014 Hi folks one of my DTW's I installed the FCC complete hop/barrel combo it fits fine but the Hop roller does not adjust the hop enough, does anyone have a good recommendation for an mod or replacement part I could install to get the hop to adjust correctly? Quote Link to post Share on other sites
Isamu Posted June 28, 2014 Report Share Posted June 28, 2014 (edited) Up to my knowledge, there are some options in your chamber: * Find a fatter nub, for example, from a silicone wire AWG16 or 14, and add a drop of glue to it, so it wont move when appling backspin to the BB. EDIT: use the red one, everybody knows "da red wunz go fasta!" * MAG concave nub, again, apply a drop of glue for better performance * Orga Flat hop, pricey, but IIRC, a user on this thread already said they worked very well Of course there are more options like sugru mods and blah blah blah, but these are the easiest to perform, although not the cheapest, except the first one Just dont forget to comment on your experiences =) Edited June 28, 2014 by Isamu Quote Link to post Share on other sites
DipTwit Posted June 28, 2014 Report Share Posted June 28, 2014 IIRC the FCC hopup has a spring instead of silicone cushions- you could switch for cushions, but for sure carefully glue the roller packing so it doesn't spin too. My MAG adjuster still doesn't get enough pull and probably needs gluing as well, which I wasn't expecting. When I glue it I'll let you know how much better it is. I tried an experiment where I shoved a third cushion under the adjuster cage, and although it gave more spin, it was crazy inconsistent- sometimes too much, other times not enough. There just isn't enough room for them without squishing up the sides, which is probably what's giving me wild differences. By far the nicest adjuster has been the orga flat. Enough spin for 0.25g bb's and consistency is good. I'm at the point where I'd buy a better barrel, or even try the orga barrel, if I wanted to improve any further. $55 wasn't cheap but I don't regret it one bit. The orga comes with a spare rubber, and I'm gonna mod my original cage to have a flat bar instead of the round pin, and put the second rubber to use. I'll post pics and my results so you can see. Quote Link to post Share on other sites
deadwood83 Posted June 29, 2014 Report Share Posted June 29, 2014 The popular consensus seems to be that the best mod for stock hop rollers seems to be gluing the stock roller then gluing a piece of Dubro RC Helicopter Fuel Line over it to make the nub fatter. There are DIY mods for flat nubs as well. I;m thinking that for cushions do you think that 16AWG silicone insulation from turnigy batteries would work? I tend to get pieces of the perfect size to go between the ring and barrel when installing deans connectors, but my condo isn't big enough to do any real testing. Oh and a warning regarding mixing and matching etiny electronics. If your A&K is the blue PCB version you will need to switch the MOSFET before switching trigger boards, or it will run the motor at 100% while on safe. Also the A&K PTW has a trigger depth similar to the CTW so CTW edition trigger boards are required since the CTW and Systema 2007 triggers were a bit shorter. Quote Link to post Share on other sites
Lyng Posted June 29, 2014 Report Share Posted June 29, 2014 Im pretty surpriced that people have to mod the MAG adjuster to get it to work, i'm overhopping .43's easy with my pdi 6.05 barrel and m130 cyl, even on my 90 cyl its easy to overhop .43's. I agree that the orga adjuster is awsome but it needs "heavy" bb's vs fps to work the best, ie 90 cyl /.28 bb. 110 cyl/.30 bb. 130 cyl/.32bb's Quote Link to post Share on other sites
DipTwit Posted June 29, 2014 Report Share Posted June 29, 2014 I was surprised about the MAG as well, after hearing everyone rave about it, but if a spot of glue makes all the difference I'm fine with that. The orga so far works the best, if it gets even better with heavier bb's then all the better, right now I'm happy with it even on .25s Quote Link to post Share on other sites
rwoodcock01 Posted June 29, 2014 Report Share Posted June 29, 2014 Thanks for the input, I have picked up the mag version first in about a weeks time it is pay day so I may grab the Orga one as well to compare. I normally run .25's as standard. Quote Link to post Share on other sites
The Insider Posted June 30, 2014 Report Share Posted June 30, 2014 @The Insider, are those "MP models" with Smith and Wesson M&P trades? They just had he standard Marine logos. Although quantity could be limited to a couple of boxes, and wont be reordered, so would be on the rarer side. Quote Link to post Share on other sites
deadwood83 Posted June 30, 2014 Report Share Posted June 30, 2014 Ah, roger that. I love the S&W trades a lot; probably because my daily carry pistol is an S&W M&P9 Pro Series. Placed an order for the G&D 10" keymod from ASGlobal. Well, my younger brother did since he loved the idea, function, and feel of my A&K rifle but didn't want all the problems. The G&D gearboxes seem to consistently show less wear inside when opened in every review I've seen. Some people have had problems with poorly dimensioned planetary and sector gears, but on my A&K those gears were fine so between his rifle and my spare parts, a truly good clone should be able to emerge. My A&K is no longer an A&K. Sadly there were too many problems with it. I wonder if the A&Ks are so hard to find due to these quality issues? On ASGlobal where I ordered my rifle the listing was, and still is, marked with "(Last One)." The final straw of parts to get replacements was the upper receiver. The barrel threading (as mentioned in some other review) is not threaded straight so when a rail is attached, it goes all cockeyed. G&P makes a replacement receiver set for ~ $180 USD (upper AND lower!) that are drop forged instead of CNC processed which should still be substantially stronger than factory Systema receivers. At the end of the day, even though I get the feeling that A&K tried fairly hard with their PTW to move away from their bad reputation it's still an A&K. So the current setup as per parts ordered is: -A&K 14.5" Steel barrel (factory! Yay! XD) -FCC CNC Ambidexterous Torque Gearbox set (en route) -Etiny MOSFET and trigger block switch (en route) -A&K Selector Board (semi has completely stopped working, but I think that's because of the stock MOSFET/trigger since switch boards are pretty hard to kill) -G&P SR-16 M5 drop forged receiver set (en route) -Modified Colt 6-position buffer tube (DIY) -Modified G27 grip (DIY) -FCC Noveske URX4 10" hand guard (en route) -Troy FDE BUIS set (stolen from one of my real rifles) -Aimpoint Comp M2 (stolen from another of my rifles) -JG/Golden Eagle Motor (en route) -Magpul CTR Mil-Spec Tube Stock (also stolen from my real parts collection) -FCC Gen 2 Hop (need to find a good wire to use the insulation for packing instead of the bad FCC spring, anybody know the size of the packings? Mine got lost in grey carpet) (en route) -MAG concave roller (en route, will be glued) -Vanaras 384mm inner barrel (en route) -Spare MC-51 flash hider that doesn't require an allen key to remove -A&K M130 cylinder and King Arms M90 cylinder (be careful! the King Arms cylinders DO NOT come lubed!) I'm not a huge fan of the KeyMod system in terms of looks, but the comfort and stability of the smaller and un-railed handguard is too much to pass up. Weight savings over rails are very real and you get the solidness of a free float handguard. Plus the larger portion of the keyhole is dimensioned perfectly for a QD sling swivel. I do have one picture of my rifle before everything started breaking. The day after receiving it. Quote Link to post Share on other sites
DipTwit Posted June 30, 2014 Report Share Posted June 30, 2014 Wow that's an impressive parts list!! Another warning about the KA cylinder- they don't use a small allen screw to keep the piston head bolt from coming loose- which of course mine did... Need to find a way to fix that in place Quote Link to post Share on other sites
deadwood83 Posted June 30, 2014 Report Share Posted June 30, 2014 Red loctite? Quote Link to post Share on other sites
DipTwit Posted June 30, 2014 Report Share Posted June 30, 2014 All I had was blue, but it did the trick, I'll keep an eye on it. I glued the MAG adjuster and it lifts 0.25s just fine now, not sure how it would lift heavier ones though. Pretty good consistency now at least. Quote Link to post Share on other sites
deadwood83 Posted July 1, 2014 Report Share Posted July 1, 2014 (edited) SO a little update. The blue board A&Ks are NOT CTW clone electronics as suggested here: http://www.airsoftcanada.com/showpost.php?p=1810670&postcount=22 I tried to fit my CTW-compatible etiny trigger board and the button was too low for the trigger to push. It was an easy fix (desolder big button from A&K board and replace small button on etiny with larger a&k) but just a heads up. Hoping to get my other stuff all installed today. Took apart the A&K motor yesterday and my goodness it was poorly assembled. One of the four screws on the pinion end was cross threaded at the factory and wouldn't secure one corner of that magnet... so they ground it off. The brushes don't match the comms at all (but at least everything should b easy to solder!), and there was what appears to be chunks of blue enamel on all the bearing faces. I hit it with motor cleaner and I'm ready to rebuild it but the broken ends of the plastic screws are still stuck in the endbell. I have no idea how to remove those. Edited July 1, 2014 by deadwood83 Quote Link to post Share on other sites
DipTwit Posted July 1, 2014 Report Share Posted July 1, 2014 Wow! I think I might have lucked out getting a decent A&K... But we will see how long my motor lasts ???? You can get screw extractors that are pretty small - the kind with reverse threads so you can unscrew things like that. I'm curious about your comment about brushes not matching the comms- did you snap a pic so I can see what you mean? Quote Link to post Share on other sites
deadwood83 Posted July 1, 2014 Report Share Posted July 1, 2014 Most definitely. I think some of the poor motor performance is related to the whole brush/comm problem. Even cleaning brushes and comms in a normal AEG motor (spinning 19k rpm) can net you a gain of 60 rounds/min. I would think then that the effect would be greater for higher RPM motors (such as PTW motors). The problem is that these clone motors rarely have the brushes in the proper shape. This can, of course, be remedied a bit by proper low-voltage no-load break-in then a cleaning, but that will cause brush wear on brushes that may already have a short life. But brushes are cheap. Improper shape, as we know, causes arcing on the motor which results in a ton of oxidation and non-conductive carbon crud, such as in this picture of my A&K motor comm: Of course, this wouldn't be a problem if the brushes were held/manufactured vertically and made good contact without warping the edges and generally falling apart: What isn't shown that I should have snapped a pic of is the other side of the large epoxy gloop at the base. It is wide and sloppy enough that there is a dark black line where it has been rubbing against the endbell/housing. Oh and here's where they ground off a screw that was cross-threaded instead of actually securing that side of the magnet... Quote Link to post Share on other sites
richwuk Posted July 1, 2014 Report Share Posted July 1, 2014 Very tempted to buy one of those 2014 G&D's but next question is magazines - not sure if I will be in uncharted territory given they have changed the hop. Reading back I see some problems with the G&D mags but are they generally the best for a G&D? A&K come out a little cheaper, vandas are tight fit and what about MAG's? Anything else I should be looking at? Quote Link to post Share on other sites
rwoodcock01 Posted July 1, 2014 Report Share Posted July 1, 2014 Never had any problems with the G&D magazines if looked after, I also run a set of vanaras polymer magazines (from RSOV) those took a little breaking in, after gently stretching the spring I get no issues on full auto with occasional chopping with certain vanaras mags Quote Link to post Share on other sites
Isamu Posted July 2, 2014 Report Share Posted July 2, 2014 Maybe not the best answer, but when I had the G&D MAX3 I bought an A&K mag and worked flawesly =) Quote Link to post Share on other sites
Raketen Posted July 3, 2014 Report Share Posted July 3, 2014 I got a blue a&k m110 cylinder but it doenst feed with high rof.. Does anyone know a fix?I've heard that the supershooter cylinder should be the best. Quote Link to post Share on other sites
DipTwit Posted July 3, 2014 Report Share Posted July 3, 2014 I've had zero issues with mag compatibility, and if the hopup in the G&D is Systema compatible, you shouldn't either. I've tried real PMAGs with Varanas internals, some with cheapo internals, and the very affordable plastic Saber ones (I got them from UNCompany 5 for $64 before discounts) No problems at all, except one PMAG I got well-used and was worn in several places, so I replaced the internals. I'm curious to know as well about cylinders, as the ones A&K include don't take well to being taken apart - the threads at the ends must be soft, and will eventually not hold together. I also had one rack gear snap on me. The King Arms one I ordered has given me troubles too, so I want to know what the best affordable ones are. Quote Link to post Share on other sites
deadwood83 Posted July 4, 2014 Report Share Posted July 4, 2014 I'm curious about this as well. My KingArms cylinder has a locking ball too small to properly hold tension against the buffer tube cap in the receiver as well as fitting loosely. But my A&K cylinder has already ripped the rack on a piston. Now, if your KA cylinder fits your buffer tube hole (should need to compress the ball spring to make it sit flat) and it doesn't wobble in your receiver then all it needs is a good lubing and red loctite on everything. The individual components seem to be well made and quite strong. I'm curious about Celcius and PPS/Super Shooter cylinders though. Maybe they're better? I think Celcius has a bearing on the spring guide which I definitely like the idea of. It's hard to swallow the thought of needing to run $200 Systema cylinders in a $300 gun... though my rifle is definitely closer to $850 now. But when it cycles there's zero whine, just a loud pop so I'm very content. Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.