aznriptide859 Posted January 30, 2014 Report Share Posted January 30, 2014 I own both the TLR-1S and TLR-1 HL (used for my Glocks), but was searching for a X300/X300 Ultra for both my M&P and XDM-40. NOt wanting to spend $200 for a light for a GBB, I found this Emerson X300 Ultra online for a reasonable price, but most importantly, it had full and correct lasered trademarks. I purchased it off CombatGearing.com (http://www.combatgearing.com/emerson-x300-ultra-led-tactical-flashlight-p-8937.html?cPath=475_603) for $72, although CG's price varies widely depending on discounts and whatnot (I've seen it as low as $65 last week). Shipping took about 10 days from HK to Texas. The light comes in possibly the shittiest, flimsiest, most useless plastic case in the world. I almost broke it by putting my coffee mug on top. Inside is the light...duh. Under the bottom foam comes adapter pieces for wider rail sections, as well as a wider rail locking piece and extra springs. The light itself is BEAUTIFUL. All the trademarks are correct AFAIK, and the light is VERY light - much lighter than my TLR-1's. I have no idea if the RS X300U is this light, but I'm very impressed so far. The locking mech is pretty sturdy as well. Pull back on the "serrated" levers on the top, then push the front lever from right to left. DAT TRADEMARKS *HNNGH* Light looks good too. Lens had a small scuff on the side though Light does NOT come with batteries (-1). The inside of the battery case is marked with polarities as well. The biggest surprise: this *fruitcage* is BRIGHT, I would say almost as bright as my TLR-1 HL which is rated at 630 lumens. Since the RS X300U is rated for 500 lumens, I'd guesstimate this one is rated around the same...maybe. The beam is wide yet semi-focused, so illuminating an entire room is very easy. The biggest complaint though? Both directions of the on/off lever are locking. On most weaponlights, one direction is momentary while the other is constant-on; for this one both directions is constant on. This makes the strobe function (yes, there is a strobe function) an absolute hassle to operate. I haven't taken a look into the rear switch cap yet, but I bet filing something down may fix this. Definitely would not recommend this light as a RS alternative on RS pistols, when decisive operation of a weaponlight is required. Overall? Amazing light for $70. Great build quality, spot on full trademarks, and very very bright for a cloned light. Definitely would not recommend for RS shooters, but for airsoft? Definitely the best X300 clone out there (which TBH doesn't say much, since this is only 1 of 2-3 X300U clones out there lol). Some more pics: Size comparison vs. TLR-1S and TLR-1 HL. Mounted on WE XDM-40. Mounted on RS S&W M&P9. 1 Quote Link to post Share on other sites
aznriptide859 Posted January 31, 2014 Author Report Share Posted January 31, 2014 MAJOR EDIT: It seems I was incorrect regarding the switch functioning. For the TLR-1S, one side's switch is momentary on, while the other side locks for constant on. After watching some videos, for the Surefire X300 the temporary on is activated by PUSHING the sides of the switches. Constant on locks are applicable for both directions of the switch's swing - this is the inherent design of the light. For the clone, the switch replicates this precisely. Press the switch (either side) for momentary on, press it again for strobe. The switch is flipped in either direction for constant on. So, for all intents and purposes, the switch functions exactly like the RS model. This is completely my fault, I did not understand the switch function when I first used it. Please disregard that bit in the original post - the light functions as it's supposed to, so it is no longer a con/complaint 1 Quote Link to post Share on other sites
Stuey Posted January 31, 2014 Report Share Posted January 31, 2014 I was about to mention that but looks like you got it Damn, I need this for my Sig! Only problem then is holsters... Quote Link to post Share on other sites
fabio Posted February 5, 2014 Report Share Posted February 5, 2014 thats a awesome looking Clone, Might Have to look into one soon for my 1911 Quote Link to post Share on other sites
hitmanNo2 Posted February 9, 2014 Report Share Posted February 9, 2014 These look to be the same ones as on PX airsoft for $65. Quote Link to post Share on other sites
emp3ror86 Posted March 5, 2014 Report Share Posted March 5, 2014 These look to be the same ones as on PX airsoft for $65. Is that confirmed by someone? 65 USD seems much more acceptable than 90+... Quote Link to post Share on other sites
hitmanNo2 Posted March 5, 2014 Report Share Posted March 5, 2014 There are some x300Us on Boom at $64 too. Impossible to tell unless they're side by side I suppose. 1 Quote Link to post Share on other sites
Hanger Posted March 5, 2014 Report Share Posted March 5, 2014 Check on aliexpress.com search "X300U" Quote Link to post Share on other sites
SwatMP5man Posted March 5, 2014 Report Share Posted March 5, 2014 Is that confirmed by someone? 65 USD seems much more acceptable than 90+... The PX Airsoft one IS NOT the same as the OP's one. The one PX stock is different, the mounting hardware is different in appearance, the torch lens is also difference (plain glass compared to have the centre part frosted). Biggest downside is no strobe Quote Link to post Share on other sites
Hanger Posted March 6, 2014 Report Share Posted March 6, 2014 Check on aliexpress.com search "X300U" Got my full trade X300 from Aliexpress for roughly $45 shipped. Would've picked up the Ultra instead if they were out Go get yourself a DG switch from Surefire. Found one on ebay for $30 used. Pretty sweet Quote Link to post Share on other sites
BigAl Posted March 6, 2014 Report Share Posted March 6, 2014 Yuo mean the surefire switch fits the clone? Quote Link to post Share on other sites
emp3ror86 Posted March 6, 2014 Report Share Posted March 6, 2014 The PX Airsoft one IS NOT the same as the OP's one. The one PX stock is different, the mounting hardware is different in appearance, the torch lens is also difference (plain glass compared to have the centre part frosted). Biggest downside is no strobe Thank you! Quote Link to post Share on other sites
christhesecond Posted March 6, 2014 Report Share Posted March 6, 2014 I have the x300 from px and my real dg switch fits it perfectly. Quote Link to post Share on other sites
Hanger Posted March 6, 2014 Report Share Posted March 6, 2014 Yuo mean the surefire switch fits the clone? Yes it does! The picture I posted is Clone X300 with real Surefire switch! Quote Link to post Share on other sites
BigAl Posted March 6, 2014 Report Share Posted March 6, 2014 NIce, does it fit the U, anyone know? Quote Link to post Share on other sites
NonEx Posted March 7, 2014 Report Share Posted March 7, 2014 I got one of these on the way in the mail. Will let you know what I think once it gets here, hopefully next week. Quote Link to post Share on other sites
CplHicks Posted March 11, 2014 Report Share Posted March 11, 2014 Mine from PX airsoft. Came in at £53 delivered. Quality is good, but I dont think the one I have is near 500 lumen. On a plus note, it fits in my Safariland for G17 with M3 Quote Link to post Share on other sites
NonEx Posted March 11, 2014 Report Share Posted March 11, 2014 (edited) Why are we mixing reviews of two different brands in the same thread ? I got my Emerson X300 Ultra today. Managed to break it within 5 minutes. I had some sort of sticky/oily residue on the front of the light housing, so I tried unscrewing the front so I could clean it off easier. Well the wiring inside was kinda so-so and when I went to screw it back together the wires just broke clean off on one end. Now, it is my own fault for two reasons. 1) Unscrewing the light housing, not recommended. and 2) Not taking care to reverse rotate the light housing so the cables would not overtwist when screwing the housing back in again, I did try though, obviously not hard enough. I didn't even think that the housing front cap and wiring/PCB would be connected like this causing this problem. Seems odd. Nothing some new wires and a few minutes with a soldering iron can't fix, but I was like FUUUUUUUUUUUUUUCK... Also I have no batteries for it yet, fresh out of CR123A But yeah, it looks and feels nice enough for sure. I mainly got it for looks. In hindsight I probably could of done with a cheaper version, this came in at just about 100 USD with shipping from Combatgearing website. Not a fan of the lock and unlock mechanism for the rail attachment for the 1913 rail. Da fuq sliding the while locking rod out to one side ? The M3 light is much better IMO, just press down on either side and pop it on/off. But whatever. I will update once I get batteries and put this thing back together :| Edited March 11, 2014 by NonEx Quote Link to post Share on other sites
Hanger Posted March 11, 2014 Report Share Posted March 11, 2014 I don't think any of the replica (X300/X300U) are truly rated at 500 lumens. Only for RS X300U is rated at 500. Pretty sure the replica are 300 lumens only, some sites listed misleading info, perhaps copied straight from Surefire site Quote Link to post Share on other sites
aznriptide859 Posted March 11, 2014 Author Report Share Posted March 11, 2014 Damn that sucks NonEx. I had a similar issue with an Element ScoutLight; broke one of the wires, and couldn't solder it back on, so I just gave up on fixing it. Hopefully you can fix the 300U though! 1 Quote Link to post Share on other sites
hitmanNo2 Posted March 11, 2014 Report Share Posted March 11, 2014 Ha. I nearly did the same thing. Got a 300U last week and started checking it out, unscrewed the front and saw the dodgy wiring. Carefully screwed it back on and thought to myself I won't be opening that up again unless it goes wrong heh. 2 Quote Link to post Share on other sites
NonEx Posted March 11, 2014 Report Share Posted March 11, 2014 Good call It looks fixable though, just two plain wires and easily accessible soldering points on both ends. I will outsource it to a friend though Quote Link to post Share on other sites
kojak Posted March 12, 2014 Report Share Posted March 12, 2014 Why are we mixing reviews of two different brands in the same thread ? ... For one thing it helps to break down the dubious Chinese knockoff branding: PX doesn't list a manufacturer for theirs. Boomarms' is simply labeled ACM, and JK Army's is MIC Cross. It's unlikely that four different factories started making trademarked X300 Ultra clones at the same time. 2 Quote Link to post Share on other sites
aznriptide859 Posted July 2, 2014 Author Report Share Posted July 2, 2014 OK there's a bit of an update I had to address on this review: The switch is ABSOLUTE *suitcase*. On BOTH my X300U's, after about a month of use, the switches would refuse to bright up at 100% brightness, no matter how hard I pressed the momentary-on switch. I found later the metal used for the switch assembly is really low quality, and their travel distance (how much it travels when you press the switch) in order to complete the circuit to turn on the light varies heavily between light and light (even side to side). I really want to buy replacement Surefire switches, but in the meantime I had to add small nubs of solder spacer inbetween the switch and the switch membrane to make them work. I can put up more detailed pictures if anyone wants, but for now, I'd say hold off on buying it, unless 1. you can get it at a steal, or 2. you're willing to work/tinker with the switch. Quote Link to post Share on other sites
intinerious Posted July 2, 2014 Report Share Posted July 2, 2014 OK there's a bit of an update I had to address on this review: The switch is ABSOLUTE *suitcase*. On BOTH my X300U's, after about a month of use, the switches would refuse to bright up at 100% brightness, no matter how hard I pressed the momentary-on switch. I found later the metal used for the switch assembly is really low quality, and their travel distance (how much it travels when you press the switch) in order to complete the circuit to turn on the light varies heavily between light and light (even side to side). I really want to buy replacement Surefire switches, but in the meantime I had to add small nubs of solder spacer inbetween the switch and the switch membrane to make them work. I can put up more detailed pictures if anyone wants, but for now, I'd say hold off on buying it, unless 1. you can get it at a steal, or 2. you're willing to work/tinker with the ###### switch. Please do post pics! It happens on the x300 copies too, though I dunno if they're Emerson or AABB brands (or if they come from the same OEM). My x300 had issues out of the box, one side lights up 50%, the other 100%. Also the 50% side requires me to push the button all the way in to make the light turn on. Had to buy a Fire Krylin switch to solve the issue but the FK switch has problems of it's own since it's slightly offspec to the ACM X300. Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.