Jump to content

Recommended Posts

Squad 701 took his safety out a few weeks ago.  Seems to be OK irc.

 

 

The safety comes out from each side, but the central pin removal didn't effect the shooting of the gun, well not yet anyhow
I put a few magazines through and everything was fine

  • Like 1

Share this post


Link to post
Share on other sites

Not a fan of it personally.. not enough to put me off but I'd rather it weren't there! Would look much cleaner without I think.

 

That's basically a 10.8 version of the M&P your looking for DZ ;)

 

It will be a while before you see a Titanium slide I'm afraid, as the Detonator kits will be released first through Enten, more or less similar to the previous kits for WE they made, with the exception of the hop-up dial showing in the slide cut-out on the side when it's racked :(

and no sights included.

But they should be available in Hong Kong at the cheaper price within the next month.

Share this post


Link to post
Share on other sites

has anyone picked up the detonator ATEI slide specifically made for the Marui M&P yet?? 

(apparently detonator released it at the beginning of september already)

 

really want to know if its easy to fit and stuff (detonator has a record in my opinion but just wanted to see if any fans of the tm m&p have it yet!! 

Edited by RogueSystem087

Share this post


Link to post
Share on other sites

Remove the back grip, remove the screw that holds the hammer casing assembly, punch pin going through the hammer casing out and pull the hammer casing assembly.

 

Left and right safeties can detach from the center pin piece. Do mind the detent pin.

 

You can remove the right thumb safety only (safety function gets disabled). You can also just remove the left thumb safety....safety function stays. Or....you can remove the thumb safety assembly.

 

You do this procedure in a couple of minutes or so.

  • Like 1

Share this post


Link to post
Share on other sites

Thanks for posting these safety removal tips. The only thing stopping me from buying the TM M&P 9 is the safety. I don't need them on my real striker fired guns and I don't need them on my Airsoft.

Share this post


Link to post
Share on other sites

Ok, stupid quick question time to anyone that owns one of these.

 

What are we looking at under the baseplate of the magazine? It is a long screw holding the mag together on these like a 1911 / SIG / Glock or a set of pins like the older M9 design?

 

After getting one but screw magazines I find easier to work on.

 

'FireKnife'

Edited by FireKnife

Share this post


Link to post
Share on other sites

hiya fireknife, 

 

i was curious about this too so i took mine apart a short while ago

post-98376-0-46310300-1411984796_thumb.jpg

there are just two pins holding the bottom part of the magazine it seems. 

quite easy to get them off if you have a kit to punch out these pins

 

but i agree, would be much easier to deal with if it were just a screw holding it

Edited by RogueSystem087

Share this post


Link to post
Share on other sites

Cock-flap.

 

Ah well I will just have to look at getting a tool for pin punching then :P.

 

I always have a single magazine that never seem to survive the winter. Odd as I always try and keep a good ambient temperature in my flat so not sure why I always get at least one fail.

 

But with a screw mag it is just un-screw, lube up or replace o-rin at base of mag and away.

 

'FireKnife'

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×

Important Information

By using this site, you agree to our Terms of Use and the use of session cookies.