bankz5152 Posted November 25, 2015 Report Share Posted November 25, 2015 What on earth. That is horrendous. Whats that top rail you have? Looks interesting. 1 Quote Link to post Share on other sites
BioRage Posted November 25, 2015 Report Share Posted November 25, 2015 (edited) What on earth. That is horrendous. Whats that top rail you have? Looks interesting. wtb video right miao Edited November 25, 2015 by BioRage Quote Link to post Share on other sites
dealda Posted November 25, 2015 Report Share Posted November 25, 2015 Looks like the NcStar Carry Handle Mount. Quote Link to post Share on other sites
mh78 Posted November 25, 2015 Report Share Posted November 25, 2015 Elaborate?It's just a mod mentioned in a youtube vid posted before. Starts around 7:50 mark. 1 Quote Link to post Share on other sites
bankz5152 Posted November 25, 2015 Report Share Posted November 25, 2015 Awesome! How thick a peice of rubber ? on my phone, my spelling will suck Quote Link to post Share on other sites
Aengus Posted November 25, 2015 Report Share Posted November 25, 2015 Awesome! How thick a peice of rubber ? on my phone, my spelling will suck About 1mm according to the video. 1 Quote Link to post Share on other sites
blobface Posted November 25, 2015 Report Share Posted November 25, 2015 (edited) It looks like your P90 is an AEG with a very short cord that plugs into the wall... *ps thanks for the spacer tips, just bought some sheets off eBay to try out. Edited November 25, 2015 by blobface 1 Quote Link to post Share on other sites
renegadecow Posted November 25, 2015 Report Share Posted November 25, 2015 Bought some sheets? Jeez, whatever happened to stealing a bicycle tire for the rubber interior. Quote Link to post Share on other sites
blobface Posted November 25, 2015 Report Share Posted November 25, 2015 lol imagine how annoyed someone would be when they found out their expensive fixie's had its wheel stolen because some guy needed 10x10mm worth of rubber... Quote Link to post Share on other sites
CaptCalvin Posted November 25, 2015 Report Share Posted November 25, 2015 Maybe it's just me but I can find "scrap" rubber all over my house. Quote Link to post Share on other sites
johnyew Posted November 27, 2015 Report Share Posted November 27, 2015 Good news: Following the video, I polished both surfaces of the trigger assembly to a mirror finish, applied a drop of ceramic grease to them and bent the ends of the transfer rod. Trigger pull is now light and crisp. Yeah!!! Bad news: 3 of my 4 mags leak. Not from the square end but from the back of the brass cover that houses the outlet valve. Still trying to figure it out. Anybody here fixed it? Sigh..... Quote Link to post Share on other sites
renegadecow Posted November 27, 2015 Report Share Posted November 27, 2015 There should be an o-ring under there, no.148. Take it out, inspect for tears, flip it around or replace. Quote Link to post Share on other sites
johnyew Posted November 27, 2015 Report Share Posted November 27, 2015 Thx. Quote Link to post Share on other sites
blobface Posted November 29, 2015 Report Share Posted November 29, 2015 The rubber sheet mod worked really well, which is actually kinda annoying, how does it take someone to come up with a mod that takes 15 seconds and a piece of rubber to fix a major functional issue that WE couldn't have just included in the 5 years they had is perplexing. And yeah, I've got two mags where the o-ring leaks now when inserted because the o-ring has been nicked by the previous misalignment before the rubber mod, flipped them around and added some silicone oil has temporarily fixed it. I think it's part no.136, the one that sits on the internal diameter of the brass part. Ordered 50 replacement o-rings... (I think it's 4.5mm ID x 1.5mm CS) Will see how they work. 1 Quote Link to post Share on other sites
Habakure Posted November 29, 2015 Report Share Posted November 29, 2015 Interested in how those o-rings work out (probably absolutely fine). Quote Link to post Share on other sites
CaptCalvin Posted November 30, 2015 Report Share Posted November 30, 2015 The rubber sheet mod worked really well, which is actually kinda annoying, how does it take someone to come up with a mod that takes 15 seconds and a piece of rubber to fix a major functional issue that WE couldn't have just included in the 5 years they had is perplexing. And yeah, I've got two mags where the o-ring leaks now when inserted because the o-ring has been nicked by the previous misalignment before the rubber mod, flipped them around and added some silicone oil has temporarily fixed it. I think it's part no.136, the one that sits on the internal diameter of the brass part. Ordered 50 replacement o-rings... (I think it's 4.5mm ID x 1.5mm CS) Will see how they work. Well probably because those are the dimensions of the real steel. The gap is present in real steel. However real steel mags are aligned by a peg in the receiver that goes into a hole in the magazine. I'd imagine a hole in the WE magazine would mean the peg would protrude into the bb channel. But you're right. Lot's of issues including this one should've been obvious after minimal testing. In fact in the prototype video when the guy ejected the magazine all the gas from the gun vented. Not sure if the one way valves are integrated into the prototype or they ran into the problem of stuck brass nipples. If it's the latter then just flat out ignored it and were happy with the gun working for the first 100 rounds or so. Quote Link to post Share on other sites
renegadecow Posted November 30, 2015 Report Share Posted November 30, 2015 I don't think any of the prototypes shown 5 years ago had those coupling valves. So no telling how long they've implemented it when they put the project back on the table. Quote Link to post Share on other sites
renegadecow Posted December 5, 2015 Report Share Posted December 5, 2015 (edited) Just something to be aware of, apparently someone locally had their hammer break on them. Initial complaint was loss of semi auto but with a broken hammer I doubt it would fire in any mode. No idea on how it happened if it was user error or a design flaw like on their AK. Edit: Sorry, not the hammer but the disconnector. Edited December 5, 2015 by renegadecow 1 Quote Link to post Share on other sites
BioRage Posted December 8, 2015 Report Share Posted December 8, 2015 (edited) https://www.facebook.com/airsoftDIYmod/posts/1685041655073290 Edited December 8, 2015 by BioRage Quote Link to post Share on other sites
renegadecow Posted December 10, 2015 Report Share Posted December 10, 2015 Rather annoying, I got my mags BEFORE my gun's even arrived and one of them's leaking. It was o-ring number 135 which fits outside of part 132. The sides were nicked from installation at the factory as the shelf it sits in is pretty sharp. Not having a replacement (one of those really thin o-rings) I just degreased it and put on some sealant before reassembly. Quote Link to post Share on other sites
BioRage Posted December 14, 2015 Report Share Posted December 14, 2015 Anyone have tan model? Would like some pictures! Quote Link to post Share on other sites
renegadecow Posted December 15, 2015 Report Share Posted December 15, 2015 Mine's finally arrived though it's still with a mate. Sad that it didn't come with the dino dildo loader. Quote Link to post Share on other sites
blobface Posted December 15, 2015 Report Share Posted December 15, 2015 ... Confiscated by customs? Quote Link to post Share on other sites
renegadecow Posted December 15, 2015 Report Share Posted December 15, 2015 I wouldn't be surprised, but it didn't go through regular channels. Spirited away by a lonely shop attendant is my best bet. Came with bullet stickers though. 1 Quote Link to post Share on other sites
CaptCalvin Posted December 15, 2015 Report Share Posted December 15, 2015 So they would confiscate phallic looking objects but leave a gun alone? 1 Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.