Jump to content

Recommended Posts

  • Replies 645
  • Created
  • Last Reply

Top Posters In This Topic

  • 2 weeks later...
Everyone knows that we now have a winner of the popularity contest of this thread which is non-existant.

 

Hardboiled, can you pm me a list of everything on there? I think I just found my next project.  :D

 

Boomarms Raptor II custom (meusoc base, prime aluminium Raptor II kit)

Sheriff Extended wide Safety (silver)

Sheriff Extended wide slidestop (silver)

X-fire threaded barrel

Delta Force Silencer (sanded)

Strengthened Recoil and Hammer springs

sanded and polished gripscrews and extractor

Wilson bumpered 15rnd magazine.

 

cheers.

Edited by hardboiledcop
Link to post
Share on other sites

M16_SIR.jpg

 

M16A4 MAX PTW 1430$

Changed to M4 lenght steel barrel 200$

Samurai SIR 190$

Samurai flipup 25$

RS Eotech 552 400$

RS M93B Magpul stock 220$

RS Magwell 50$

 

LI-PO in sling with modified stock and sling.. $priceless :P

Edited by IBICO
Link to post
Share on other sites

I think there should be a new rule for picture threads: if there's no picture posted for more than a page (20 posts), then it's time to close that picture thread. ;)

 

 

 

Anyways, thread cleaned and re-opened, but take whatever general discussion you may have to the non-picture threads, and post only pictures and picture-related questions/clarifications here. If we can not keep this thread clean, it shall be closed for good, and spammers punished.

Link to post
Share on other sites
  • 2 weeks later...

some of you may laugh. . but I have at least $1k worth of hours invested into my Custom H&K SP89. :

 

MHHKSP89-1.jpg

 

MHHKSP89rightside-1.jpg

 

working on functional bolt. . .

 

MHHKSP89weldright-1.jpg

 

simulated weld marks

 

MHHKSP89assembly1-1.jpg

 

quick change spring like PGC M249 mechbox

 

MHHKSP89assembly2-1.jpg

 

notice Ver 2 mechbox and modified MC51 lower receiver

 

MHHKSP89rearreceiverpin2-1.jpg

 

stock receiver pin going through mechbox. . .

 

MHHKSP8901left-1.jpg

 

notice the selector stop. . it STOPS at "1"

 

MHHKSP8901nozzle-1.jpg

 

notice LENGTH of custom nozzle compared to stock MP5k nozzle

 

and I am still not done!!!!

Edited by the cleaner
Link to post
Share on other sites

Almost finished. Next step is to machine a RealSteel upper for it.

 

Systema PTW MAX M16A4 w/M4 outer steel barrel

Samurai SIR

Samurai flipup

RS PRI gasblokk

RS Eotech 552

RS Surefire M951C

RS vertical frontgrep

RS Magwell

RS Magpul stock with electronics inside

7.4v LI-PO batteri inside the sling.

 

 

m16_shorty.sized.jpg

Link to post
Share on other sites
how did you make that nosle mate. ?.. love that gun. very nice.

 

I machined them. . .the prototype nozzle is the clear polycarbonate one. . the one installed is a nylon one. .more forgiving and not as brittle.

 

eventually, I have a CA MP5k metal receiver that I'll install. . .

Edited by the cleaner
Link to post
Share on other sites

IMGP1798.JPG

 

All three easily qualify for the 1K club. From the top:

 

TM M14 w/ wood stock, PDI barrel, 126mps upgrade, new wiring, 6 mags. The Aimpoint Comp M on the A2 usually sits on top of the M14.

Systema M16A2 MAX PTW w/ M130 cylinder and a total of 7 mags for both PTWs

Systema M4 gen.III PTW w/ Midwest RAS, Eotech 512, RS front sight and trigger guard, custom engraved receiver and M90 cylinder.

Edited by Carbine
Link to post
Share on other sites
Nice gun squeeky, just wondering how's the magnum motor?  I'm thinking about getting one in the near future.

 

The magnum motor is phenominal. I can use a 9.6v battery to push my m150 while still maintaining a decent rof. But sicne im using semi only, and a 12v, it allows me to fire shot after shot without a delay in trigger pull.

Link to post
Share on other sites
Guest
This topic is now closed to further replies.
×
×
  • Create New...

Important Information

By using this site, you agree to our Terms of Use and the use of session cookies.