Search the Community
Showing results for tags 'walther'.
Found 3 results
Unfortunately there is no review thread for this bad boy yet, and the news thread is locked. But I have some new info I need to share so I'll start up a review thread for this. I don't have any review material yet per say but I'll put my two PPQ videos here for now. And a new one coming in a few days. Anyways. What I want to address is the cracking of the upper slide flat top due to the chamber on the outer barrel. I recently bought a new Asia version slide for my PPQ to replace, and I modded the chamber by chamfering off the front edge. Significantly might I add. And I noticed the chamber was still going up onto the slide upon cycling. Well, turn out the nozzle is getting stuck on the back end of the barrel/chamber on cycling, pushing onto the barrel, preventing it from dropping down on cycling. This pushes the chamber of the barrel up into the top of the slide. So I filed down a front edge on the nozzle, and cleaned up the back end of the barrel/chamber and lubed the parts up. Does it completely fix the issue? Sadly not. The nozzle and barrel still interlock a little bit. But I think with these two mods, I hope, enough is done to mitigate, or at least reduce the risk significantly, of breaking the slide (again). Other than that. Let me add this: Difference between Asia and Euro version: Asia: Full markings, longer inner barrel, blocked full auto function. Non Umarex branded. Euro: Not fully marked, shortel inner barrel, functional full auto function. Umarex licensed/branded.
The WE P-38,The first *actual* full metal airsoft replica of the walther P-38, has at long last landed in my hands. I have been excited about this gun from the day that WE teased about it, showing the prototype in the white along with the M84, Makarov and P99. These are my initial impressions of it. While I understand that the P38 has been available for months, I was not a fan of the cheap looking "Blue" version, and so I waited for it to be available in normal black. There are some "Blue" parts to even the black P-38, and seeing the finish on them, Im very happy I waited. I will say that I am not disappointed by the painted finish at all, but more on that later. First, some pictures: Left side: Right side: Breach open: The fit and finish are very nice. Not only for a WE product, but for any airsoft gun. There is very little play between parts, or slack to the return spring. the barrel does rattle slightly when the slide is retracted, but i imagine this is likely the case on the real one as well. There was a lot of talk about whether or not this particular model was a clone of the older Maruzen model. Having both to compare, I can say that the WE version is not a straight up clone. Maruzen's gun was without question the basis for the WE design, however, WE seem to have taken Maruzens version and improved it in many ways. So, many of the parts are completely different, though some are identical. For example, The hopup unit is here: While it does bear a resemblance to the maruzen unit, both the hopup unit and loading nozzle are completely incompatible. The loading nozzle is a different shape which uses a standard WE setup. It doesnt have the two holes in the magazine gas bucking either like the Maruzen does. More interesting is the hopup bucking itself: Unlike the Maruzen version, It appears that the WE uses a standard VSR-10 type bucking, which would give it a lot of upgrade potential. Another one of the parts which has been redesigned is the valve striker system. Whereas the Maruzen had a thin striker which was forced through a pot metal guide block (Which coincidentally wore out on all of my Maruzens, turning them into paperweights), WE seems to have simplified this portion of the design: The valve striker is now much more conventional, And along the lines of many of WE's other GBB pistols. It also looks like it cant eat itself apart ala the Maruzen version. Here is a picture of all major parts disassembled. Some parts like the barrel locking lug and leaf spring are identical to maruzen. I imagine that the safety, slide release, and take down levers are also compatible, were you to need replacement parts. Gas consumption seems moderate. filled normally, the magazine will give approximately two magazines worth of BBs per fill. the second mag, depending on the time given, may not lock back the slide, but there is no problem with the first run. However, using the usual trick for single stack mags, where the first fill of gas is rapidly discharged manually, and then filled again, I was able to get 2-3 mags with slidelock, plus another 2 mags worth without locking. (This works for many other single stack magazines as well, like the 1911's and Lugers) Output seems to be relatively consistent over the first two mags (When venting/filling). Hovering between 285 and 295 fps. And dipping down to about 270 and change as the magazine cooled down during the third go. During the first fill of BB's however, there was no major dip in fps. Recoil is relatively light but very crisp. No slop to it at all. I wasn't able to do a proper accuracy test, though at 50-ish feet i could hit a torso sized target without an issue. I plan to go back and do one properly with pictures when i get another chance though. A few other notes. Maruzen mags are not compatible. The gas release valve is very different on the maruzen, as well as the gas bucking. The slides and frames, while they will swap between the WE and Maruzen, do not function when doing so. And, Maruzen grips will fit the WE just fine. Now, about the paint. I think this is about as proper a paintjob as Ive seen on a WE gun. Its not the usual thin garbage they used to use. While im sure it isnt anything special, If you notice the right side of my barrel has some scuffs in it. This is because while messing around during testing, a kwa 1911a1 magazine with a steel baseplate fell on the p38 from standing height. It scuffed the paint but didnt scratch it, so i think the paint is fairly durable. I would buff it out, but i'll just wait till i can get a replacement. If you look you'll see that the magazine does still have the "Blue" finish like the original release. Some people thought the rainbow effect might just be from the cameras, but its not. It seriously just looks like swirly rainbow ###### in person too. And one last thing. Because of the Redwolf video, some people might think the P38 has no double action feature. This is not the case, It's double action works the same as on the real steel P38. Meaning, the gun actually has to be chambered first and then decocked. Simply inserting a magazine and pulling the trigger will do nothing as the valve knocker isnt retracted (And on the RS P38, no round would be chambered). If you were to do that on an average Marui, it might cycle the slide, but as there would be no bb chambered, it still wouldn't accomplish anything. But, I did find it somewhat amusing that the guys at Redwolf have no clue how double action works. So, overall, I would say that if you're looking for a WW2 sidearm or just a pistol in general, i would definitely recommend WE's P38.