Jump to content

delarosa

Regular Poster
  • Content Count

    111
  • Joined

  • Last visited

About delarosa

  • Rank
    Regular Poster

Additional Information

  • Airsofter since
    2007
  • Country
    Indonesia
  1. delarosa

    Tokyo Marui's XDM-40 4.5": first impressions

    Precisely. To have a good durability on internals, the characteristic of one part to the other need to be similar, in this case hardness. Once theres one part significantly harder than the others. It is also a subject to faster wear off of the weaker ones. Same thing happens for the VSR10 piston and sear. Avoid having one part much harder than the others to maintain durability. Thus said, changing a few parts to be enhanced means there would be a possibilty that they need to change others to match. Hence the more cost will be needed. Thats why its better to leave the gun as it is or upgrade most of it.
  2. delarosa

    Tokyo Marui's XDM-40 4.5": first impressions

    Well actually pot metal are used because theres a regulation that limits the fps, thus higher grade material does not only increase cost but also not necessary as lower grade material are enough to last a long time. The problem is that we like to use green gas on pot metal. Thats the problem.
  3. delarosa

    Tokyo Marui's XDM-40 4.5": first impressions

    Get the WE trigger bar to replace that. And also remove the fire indicator, my friend has said something about performance issue with the indicator installed when using stronger gas than duster.
  4. delarosa

    Tokyo Marui's XDM-40 4.5": first impressions

    Hey guys, found the solution to the problem yesterday. Stripped it up and I got a total of 3 hammer springs to switched back and forth. Chose the strongest one and put it in. Suddenly it works. I guess I just wrongly select the matching hamspring strength the last time I put it in. Now it cycles with no problem.
  5. delarosa

    Tokyo Marui's XDM-40 4.5": first impressions

    So this is the video to show what happened. Seems like the valve knocker doesnt have enough power to hit the valve, thus why the hammer didnt go down in full when fired. And that explained why when the mag is released, the hammer would go back in place. http://youtu.be/GPhSO96VuUg
  6. delarosa

    Tokyo Marui's XDM-40 4.5": first impressions

    Came across a strange problem on my xdm since I change to metal slide. Now the hammer wouldnt hit all the way hitting the valve. And that resulted in tiny gas release. Not until i release the mag that the hammer can finally be all the way down. Seems like the hammer force is too weak compare to the valve's outward pressure. The strange thing is that if I try to rack and shoot over and over, will then the gun starts to shoot (mag condition cold). Tried upgrading hammer spring to no avail. Should i change the mag valve? Tried with new mag still had the same problem. Anyone got any experience on this?
  7. delarosa

    Tokyo Marui's XDM-40 4.5": first impressions

    Quite positive on this. The slide catch is fine, so does other internals. This one is just the reinforcement part on the slide that connects the slide and the lower frame as not to have the frictions eat away the plastic.
  8. delarosa

    Tokyo Marui's XDM-40 4.5": first impressions

    UPDATE: found out the little broken piece is the metal part on the plastic slide which connects to the lower frame of the gun. In terms of function, it wont matter much. When changing to metal slide, it wont get transferred anyway. So im all good.
  9. delarosa

    Tokyo Marui's XDM-40 4.5": first impressions

    The size is approx 4mm wide. Been trying to find where it fell from, i cant seem to find it anywhere. Its a broken part because from the pic theres the white part that indicate it was stuck on something before.
  10. delarosa

    Tokyo Marui's XDM-40 4.5": first impressions

    Sorry for late postings, heres the little metal thing that fell off when I use Green. First it made the slide stuck halfway, the when I try to rack it back, it fell off. Anyone knows what this is?
  11. delarosa

    Tokyo Marui's XDM-40 4.5": first impressions

    Dont use GG for stock xdm. I used mine and somehow the slide stucked and cant be moved, something came out of it and I dont know what it is. Will post the pic later, thought someone might know what it is.
  12. delarosa

    Tokyo Marui's XDM-40 4.5": first impressions

    Ah ic, manage to fit it in. However it seems that its going to fall off again due to recoil. Kinda strange from TM doing something like this, i expected something better like screws though. Thanks alot Deadmeat and mimesis!
  13. delarosa

    Tokyo Marui's XDM-40 4.5": first impressions

    how does that fit in? Tried few times with no luck.
  14. delarosa

    Tokyo Marui's XDM-40 4.5": first impressions

    Guys, today I tried running standard xdm using green. The blowback was insane. The front sight fell of and suddenly theres a rattle noise from the gun. I opened it and found this piece of plastic. But theres nothing in the manual having the same shape as that. Anybody know which part this is suppose to be?
  15. delarosa

    KJW M4

    From my experience using both 6.01 and 6.03, 363mm length barrel, 6.03 gives best accuracy and consistent from shot to shot. Im using Edgi barrel.
×

Important Information

By using this site, you agree to our Terms of Use and the use of session cookies.