johnyew
-
Content Count
324 -
Joined
-
Last visited
Content Type
Profiles
Forums
Gallery
Blogs
Calendar
Everything posted by johnyew
-
No, not odd at all. Please post the comics section next. Thank you very much.
-
Thx.
-
Good news: Following the video, I polished both surfaces of the trigger assembly to a mirror finish, applied a drop of ceramic grease to them and bent the ends of the transfer rod. Trigger pull is now light and crisp. Yeah!!! Bad news: 3 of my 4 mags leak. Not from the square end but from the back of the brass cover that houses the outlet valve. Still trying to figure it out. Anybody here fixed it? Sigh.....
-
I was able to remove the nozzle but could not remove the flute valve from within the nozzle. ETA: Or does the flute valve come out through the front of the nozzle? Just have to remove the cross pin?
-
If the trigger pack placed in front of you, hammer on the left, the 'lever' is on the right. There's only one piece that you can push/pull down and it springs back into position.
-
I found the way to drop the hammer fully when out of the gun. There's a 'lever' that you have to push down, located on the front right hand side of the trigger pack and lets the hammer drop fully.
-
Update: Some, somewhat, good news. I took out the gun and magazine from the hardcase, topped up the mags and left it all in my living room overnight. Today during lunchtime, I test fired the gun and everything worked fine again until the second mag and the low power problem appeared again.Took apart the barrel/hopup assembly, bolt and nozzle and trigger pack. Inspected all of it and found nothing out of the ordinary. As Dan had mentioned, the flute valve might be sticking, so I gently took a jewelers screwdriver and pushed at the flute valve and it was able to move and spring back in
-
Will update after a complete teardown and inspection. Probably tomorrow morning. Still feeling disappointed after yesterday.
-
1. the exact same bottle of gas that I had used for the gas efficiency test as it was till more than half full. 2. Did not do any chrono immediately as I had a backup gun and wanted to play instead of tinkering with it. The gun was firing fine up to 40+ meters 2 days before and hop up was fine. 3. It did it on the first shot on every mag I had; all topped up with Top Gas/GG
-
Yes, it did but almost all subsequent shots were double feed. I'll check it thoroughly tonight or tomorrow morning. Still feeling disappointed to do anything about it. Thanks.
-
I had a very disappointing day yesterday trying to field the P90 for the first time after all the preparation and test shooting I had done the week before sighting in and all. Packed up the P90 and 4 mags in a hard case and set it aside Saturday night. Woke up Sunday morning and went to the game site, got prepared for everything and topped up the mags; none were leaking as there was only an instant of flow noise and then stopped. However, did not test fire. Just loaded up the mags on my vest and headed out. Once in the site, inserted the mag, pulled back the cocking handle and fired a
-
Not sure if it was full or not, I charged it until the flow noise stopped. Set it aside for 10 minutes before shooting test.
-
I'm getting about 150 rounds full power, 151-175 visibly getting weaker, shots landing nearer and stopped my test. 26C, 0.25g, Top Gas.
-
Me too. Couldn't figure out neither.
-
Comic Sans MS
-
For me shouldering the gun, it feels neutral because the CG is right on my strong hand. The gun balances at about 1.5 inches to the rear of the selector.
-
LOL, It is one! For your wife/gf/so while you're away playing airsoft.
-
I used 550 cord and wrapped it around the grip and feels much better. Try it before changing to something else.
-
Exactly! much sadness.....
-
I have mixed results with Nine Ball purple HU rubbers, 2 have overmolding issues and 3 are fine. I've started switching to Maple Leaf Diamonds and Deltas now and so far so good. ETA: Have changed to Nine Ball Power 6.00mm inner barrel and one of the good NB rubbers.
-
G36C short side rails fit perfectly on it. No need to buy VFC specific rails.
-
Hi All, Anybody has installed the A-Plus Devil Inner Barrel and Hopup rubber set? I have recently installed mine and want to compare the accuracy and consistency of this kit. FYI, on mine, it's performing worse than the stock parts. Any comment would be appreciated.
-
Hi Dan, Thanks for the tip. I have found a shop that specializes in O-rings but I have yet to find the best size that runs without any problems for an entire day. Once I do, i'll order oil resistant ones from the same shop.
-
The ongoing problem I'm having with mine is that the original nozzle O-ring has swelled and jammed the nozzle during prolong firing. Only after about an hour or two, will it return to normal and everything works normal again. I'm a bit disappointed since this doesn't happen to my MP9, GHK AK, KJW M4 and VFC's responses have been underwhelming. I went to a local hardware store and bought O-rings of various sizes to find the best possible fit for it but still haven't found it yet and that makes me not wanting to skirmish with it, which makes me sad considering how much I had paid for it.
-
Hi Guys, Which mag pouch are you using? My current mag pouch, 3 mag setup for MP9, though can fit the MP7, taking it out during a game is very difficult. Any other options available?
