ColDaz Posted May 8, 2007 Report Share Posted May 8, 2007 Just happened upon this and haven't seen anything in the News section. One BE MP7: http://www.actionhobbys.co.uk/BE-MP7-AEG_ACICN.aspx I haven't really heard anything about these to be honest, but they aren't at RSOV or Gunners. Just so you know. Link to post Share on other sites
DazJW Posted May 8, 2007 Report Share Posted May 8, 2007 And before someone points it out, he has the WELL *aswell* as this one. Might just be a rebrand, but I'm sure there was supposed to be two different MP7 clones (with the WELL being a bit shoddy). Link to post Share on other sites
ColDaz Posted May 8, 2007 Author Report Share Posted May 8, 2007 The colouration looks a bit different to me. They are clones however, so I would expect them to look quite alike ... Link to post Share on other sites
Rogue845 Posted May 8, 2007 Report Share Posted May 8, 2007 The WELL is a bit shoddy. If this is a 'new' clone, we'll have to take it at it's own merits. If it is just a rebrand of the WELL R4 - stay clear. Link to post Share on other sites
DazJW Posted May 8, 2007 Report Share Posted May 8, 2007 Yeh looking at the close ups they do appear to be slightly different, but that could always just be the lighting. Just need Paul to get the details up to find out really, though I've not seen this mentioned in the China Airsoft thread which would suggest it's just a rebrand. Link to post Share on other sites
tome Posted May 8, 2007 Report Share Posted May 8, 2007 I have a well R4 and to me they look the same down to the oversized fire selector on the left hand side of the body (as compared to the tm one) Link to post Share on other sites
ColDaz Posted May 8, 2007 Author Report Share Posted May 8, 2007 Didn't Gunner have some photos up on the old site of an in development BE MP7 with no selector markings? Another photo had the Well MP7 with them? Link to post Share on other sites
DazJW Posted May 8, 2007 Report Share Posted May 8, 2007 Looking at the trigger, selector lever, RIS rails (the bits you'd expect to be metal) there's definately a different finish to them. I hope it is just the WELL, otherwise I'm going to end up wanting one Link to post Share on other sites
Arnie Posted May 8, 2007 Report Share Posted May 8, 2007 http://arniesairsoft.co.uk/news2/1899 Link to post Share on other sites
DazJW Posted May 8, 2007 Report Share Posted May 8, 2007 Hmm, sounds like it's probably a fixed up WELL or a different gun entirely then. 0o0o FN2000, no mention of the L85 though Link to post Share on other sites
Arnie Posted May 8, 2007 Report Share Posted May 8, 2007 According to my own sources it's not a Well clone as there are differences in the design. Link to post Share on other sites
titanwraith Posted May 8, 2007 Report Share Posted May 8, 2007 According to my own sources it's not a Well clone as there are differences in the design. <{POST_SNAPBACK}> I will get the review done but with website mods i have not had chance to, i have had a little time to go over it and please bear in mond i sell both , and i will try to be as un bias as i can. To be honest i feel the BE version is better than the well version, conbined with the fact i am always trying to get ahead in the trade and i have a good contact in china that can pull strings with the factories to get new lines ie. JG s-system and Para models, i am always looking for new lines, the BE version has i feel a better finish, the front grip locks where in place, the well it dose not lock all the time, the front muzzle plate has a spring in it to keep the battery secure where the well version has not, there is only a small amount of stock wobble in the BE version ,, both hop units are pants on both, i recomend changing the rubbers and the BE version has a little more noise from the box that the well version, but apart from that i feel the BE is better, the box quality is poor but so is the well version , but then again who looks at that. As far as i know its a marui clone, BE released the preview to me in january but would not supply till now, thats 4 months in prototype where the well R4 was only being prototyped for 2 month Regards Paul Link to post Share on other sites
zentaurus Posted May 9, 2007 Report Share Posted May 9, 2007 looks like i will have to get the BE as well. eager for your review, paul. cheers, zT Link to post Share on other sites
Galaxy613 Posted May 9, 2007 Report Share Posted May 9, 2007 In layman's terms, the BE MP7 is a completely new gun, NOT a Well MP7 rebrand (seriously, why the HECK would a manfuacturer rebrand another manfuacturer?) and is actually better than the Well MP7. But the Hop-up bucking on both are pants so they'll need a replacement. Even shorter: Do not get the WELL version but the BE version. Link to post Share on other sites
tome Posted May 9, 2007 Report Share Posted May 9, 2007 Where would one get a mp7 hop rubber from Link to post Share on other sites
titanwraith Posted May 10, 2007 Report Share Posted May 10, 2007 Where would one get a mp7 hop rubber from <{POST_SNAPBACK}> Finished all the website mods now, will have it review friday along with other lines not yet placed, just to let you know we also have the JG M4 SD on its way to us and also the cyma ak74 new version, not sure of details but had a scope mount added to it, the D boyi M4 A1 full metal and the cyma ak folding tactical Regards Paul Link to post Share on other sites
Habakure Posted May 22, 2007 Report Share Posted May 22, 2007 So many clones so little time, wonder if that lovely clone of the SA80 will be arriving soon? Link to post Share on other sites
Recommended Posts
Archived
This topic is now archived and is closed to further replies.