Zereck

On my Marui PX4 I never had problem cocking the weapon with safety on, however after I installed the Crusader slide it won't return fully(it stucks almost at the very end of its travel) with safety on because the slide is closer to the frame.

Noob question, but how do you remove the stock?

Well it seems VFC gbbrs will work fine as long as you live in hot places, otherwise you'll have to get CO2 mags.

I have a Magic Box piston head for upgrade and I noticed that the O-ring is kinda loose on it(you can move it a bit but it jumps back to its place), at least compared to a normal V2 piston head. Is that normal?

So I finally managed to make it work correctly mostly(will write about that later) but I still have a few issues. The slide came with a screw and 3 o-rings(all the same size). The screw is for the rear sight(different than the original), but I don't know what the o-rings are for. The gun cycles normally now but for some reason it now shoots flyers sometimes(either going left or right of the target). Is the original recoil spring is ok or shall I get another(if there is one). Also: I don't know if you can see it but I bought a Nineball hop-up rubber and after I took it off of the barrel it h

Ok so I installed my internals into the Crusader slide. First I tested the pistol with the original slide and the Crusader outer barrel: it worked without problem. However with the Crusader slide most of the time I can't pull the slide back(the whole thing stucks at the very beginning) but I noticed that if I rotate the pistol on its side I can pull the slide back easier. I tried to shoot with it but the gun would not cycle properly(couldn't even chamber a BB) except very rarely. I also tried Crusade slide and original outer combo but was even worse: the slide stuck if I pulled it back to the

Is the hop-up the same as in their AKs? In the AKs its pretty much a normal AEG hop-up but the nub is different and can only push down a small part of the rubber(the only thing I dislike about the gun).

Aye it does seem to have a hollow part in it. Well I bought the tan Crusader slide and the Detonator slide stop, so we shall see if the slide is any good.

So my slide catch broke and I was wondering if I should get the Detonator steel one instead of the default Marui one. Also does anyone have any experience with the Crusader Metal slide?

Anyone had an issue with the Ra-Tech real gun function bolt catch? I installed it correctly and I can lock the bolt back with it but when Im shooting with an empty mag the bolt rarely locks back and when it does it goes back as soon as I take the magazine out. Is there a solution to this problem?

No the gun is in relaxed position the bolt is forward: The tab just doesn't get pushed down automatically when I try to close the dust cover.

Thanks. Im already using 7.4 lipos, so it should be okay. Never had that problem, however I had multiple mags have their BB followers stuck, but those were fixed by cleaning and lubing a little the magazines.

I have a few questions about upgrading. I have the 416 but it is pretty much the same as the sopmod internally: - if I upgrade every part in the gearbox would the Eagle6 110 spring reach around 390-400 FPS? - can the Eagle6 recoil spring be used with the stock gun or should I only put it in an upgraded gun? - I bought the Lonex next gen gears. What motor would be the best? Would a Lonex A2 be too much?

I just noticed that on one of my magazine that the slide catch bumper goes higher than it should and its harder to push the slide catch down with that magazine. It still works but it is scratched a little. I disassembled both of my mags(for lubing) and couldn't figure out why was one higher than the other(no dirt, or anything and I put it together correctly). Anyone else had this problem?

No dirt. It seems more like the spring(too strong?) pushes the tab too much which hits the upper parts of the brass-ejector hole(am I saying that right?) where it doesn't get pushed down automatically anymore.

My dustcover won't close unless I push the little locking tab down with my nail. Odd as it worked well yesterday and today it just wouldn't close without help. Not that it's big issue just wondering if anyone else had this problem.

Just received mine! Looks and feels awesome. Hopefully my batteries arrive soon. Im actually thinking about not putting anything on it because I like the default look so much.

KRISS Arms Terminates Licensing with KWAHuh... tough they won't say why exactly, and it means if you won't get one now you might never will.

http://www.airsoftcommunity.it/recensioni/asg/28-marui/1113-tokyo-marui-h-k-416d Here is a full review of the gun with disassembly included. Not the best english but the pictures help.

The site was down for a month and now it seems it come back as: www.airsoftpeak.com If you had an account on the previous site it should work on the new one as well.

Well Echigoya just posted on their Facebook page that the 2nd batch is on the way and they can deliver them on the 22nd. I hope everyone can get theirs this time.

Does taping the markings down not work anymore? Btw prepare for a long wait as I have ordered mine on Feb 27. and still waiting for it. I asked Echigoya when they will get the next shipment in and they replied to my email a week ago saying: "maybe this coming summer".

Could anyone tell me the exact size of the battery compartment(width, length) please? I want to know whats the largest battery I can put in it.

I am at 1200 rounds and no damage whatsoever tough I shot mostly outside where it was cold(1-10 celsius). Gas efficency is not a problem for me, I did notice that I have to load the gas for a longer time to fill the mags up, sometimes I had to keep filling for over 10 seconds. I don't know if its the cold or certain type of cans let the gas flow slower, you can be certain if its full when the gas starts spraying while filling the mag.

Well I ordered one on Feb 26th and no delivery since then. They do wrote that it could take 1-2 months wait for next stock.