CatgutViolin Posted May 12, 2017 Report Share Posted May 12, 2017 Just keep in mind the rear tab is short by a couple or so mm and needs building up to lock in a WE. Alternatively, you could get a spare magazine catch and built it up to engage the WELL mags. No modifying mags and no permanent conversion. Link to post Share on other sites
renegadecow Posted May 12, 2017 Report Share Posted May 12, 2017 That might result with WE mags not fitting though. Link to post Share on other sites
NonEx Posted May 12, 2017 Report Share Posted May 12, 2017 I made a mistake. I got my WELL AK CO2 mag from AsiaAirsoft, not eHA. I was looking at my eHA order when opening and was like "Hmmm, where is the AK CO2 mag?" Link to post Share on other sites
IAmHated Posted May 15, 2017 Report Share Posted May 15, 2017 theyre in stock at gunfire so picked one up with few spare mags, looking forward to trying it out Link to post Share on other sites
renegadecow Posted May 22, 2017 Report Share Posted May 22, 2017 I'll just put this here: http://airsoft.tiger111hk.com/m113/Well/p35062/WELL-AKS-74U-Full-Travel-Bolt-CO2-Blow-Back-Rifle-(Black)/product_info.html http://airsoft.tiger111hk.com/m113/Well/p35063/WELL-Imitation-Wood-AK-74-Full-Travel-Bolt-CO2-Blow-Back-Rifle/product_info.html What sucks is I can't import them myself and the local store that can, specifically doesn't buy from Tiger because reasons. Link to post Share on other sites
vorpalbunnie Posted June 2, 2017 Report Share Posted June 2, 2017 Hey dudes, is there any FPS jump in the WE with these CO2 mags? I plan to run them in japan so I have to keep it under a joule. Thank! Link to post Share on other sites
Gegsite Posted October 7, 2017 Report Share Posted October 7, 2017 Hello. Anybody has a problem with the CO2 magazines as I do? I'm looking for a solution, cause the output-valve is such a weak design that 2 of my 5 working as it should. The rest is leaking. I was looked the design of that valve and it is shows very lot of common as the WE-SCAR output valve. I really must fix this problem as this stops me to use it as my primary choise Oh , I do changed the O-rings but thats not the problem as you think.... The machining of the brass hol is too loose and the pin what goes inside can wobble and the pin other end is sealing the CO2. Could not find spare output valve or anybody who knows what other brand's output-valve will fit. Any ideas or solutions? Probably not I'm the only one who has this problem. Thanks! Link to post Share on other sites
Dimitri MdP Posted October 7, 2017 Report Share Posted October 7, 2017 hmmm WE AK green gas valves are compatible with WE M4 green gas valves, so maybe the design for the Well AK CO2 valves is the same as the WE M4 CO2 valves..So try to find someone with WE "M4" STANAG magazines and check if the valves are compatible, maybe you can replace it with those. Link to post Share on other sites
Gegsite Posted October 10, 2017 Report Share Posted October 10, 2017 I did order this, cause it looks very alike that the WELL AK CO2 magazines have. http://www.ebay.de/itm/Original-WE-Ventil-Set-f%C3%BCr-die-WE-M4-CO2-Softair-Airsoft-Magazine/232497108082?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2060353.m2749.l2649 Link to post Share on other sites
Dimitri MdP Posted October 10, 2017 Report Share Posted October 10, 2017 Please let us know if it turns out to be compatible Link to post Share on other sites
Gegsite Posted October 13, 2017 Report Share Posted October 13, 2017 So today it arrived. Short verdict is : No. It is not compatible The good news is that the tap on the brass is the same so I could install it, but it was leaking a bit from start to the output, as you can see the lenght is shorter. Link to post Share on other sites
Recommended Posts
Archived
This topic is now archived and is closed to further replies.