Smith5 Posted April 14, 2010 Report Share Posted April 14, 2010 Where does everyone buy their gearbox lubricants from in the UK. There must be other sources apart from airsoft retailers. I can find lithium grease for using on the gears in abundance from several places, but what about silicone grease for the cylinder and piston parts? Link to post Share on other sites
perr_mike Posted April 14, 2010 Report Share Posted April 14, 2010 Try Halfords, they do some Silicon grease for push bikes which is pretty good and relatively cheap. Cant remember the brand name though. Link to post Share on other sites
matt.bee Posted April 14, 2010 Report Share Posted April 14, 2010 Finish Line Teflon stuff from Halfords, or their own brand Teflon lube (in a tube, it's a red grease) both found in the bike dept. Rock Shox Judy Butter or Pace RC45 are both great greases too if you can find them, they are designed for use in MTB suspension forks, so slippy and sticky at the same time (if that makes sense) and safe on rubber/plastic parts. Link to post Share on other sites
DrKalinka Posted April 14, 2010 Report Share Posted April 14, 2010 You should use some water base- Ooh.. Not that lube.. Link to post Share on other sites
Tinkerton Posted April 14, 2010 Report Share Posted April 14, 2010 Ann summers usually carries some stuff, however i was in tescos the other night and did spot some KY jel- oh wait. wrong lube Try halfords, or a motor factors, for white lithium grease. Link to post Share on other sites
Vice Posted April 14, 2010 Report Share Posted April 14, 2010 Local car shops.. I got a massive tub of white lithium grease for £3.50.. will last me years.. Link to post Share on other sites
Smith5 Posted April 14, 2010 Author Report Share Posted April 14, 2010 Well I ended up going down the Halfords route and got a massive tub of lithium grease for an relatively insignificant amount of money. Wasn't sure about the teflon stuff as it wasn't exactly clear to be by looking at the tube what it was 100 % safe/unsafe to use on; I didn't want to buy anything that could have caused my o-rings or piston to dribble out of the gearbox, so I will source that grease from somewhere else. Link to post Share on other sites
shmook Posted April 14, 2010 Report Share Posted April 14, 2010 randomly, i got a tube of silicone grease when i was in maplins Link to post Share on other sites
ED-SKaR Posted April 14, 2010 Report Share Posted April 14, 2010 randomly, i got a tube of silicone grease when i was in maplins I got some of that stuff a whyle back and i would not recomend it at all. I tried it on an AEG gearbox and i had to open it up again within a month because it was dried up. Ideally you want a gearbox set up so you dont take it apart after 10 years or more. Also tried with GBB handguns and its just a little to thick, keeps clogging things up unless i spray on some spray lube as well. The maplins spray lube is great (for GBBs, where you clean regularly). Link to post Share on other sites
Crimson Posted April 14, 2010 Report Share Posted April 14, 2010 Halfords Finish line teflon grease Finish line ceramic grease Google them both for UK stores, Halfords also sells them Link to post Share on other sites
shmook Posted April 14, 2010 Report Share Posted April 14, 2010 I got some of that stuff a whyle back and i would not recomend it at all. I tried it on an AEG gearbox and i had to open it up again within a month because it was dried up. Ideally you want a gearbox set up so you dont take it apart after 10 years or more. Also tried with GBB handguns and its just a little to thick, keeps clogging things up unless i spray on some spray lube as well. The maplins spray lube is great (for GBBs, where you clean regularly). fair enough, but i use it on my bolty, which gets stripped down every couple of months at least, so gets re-applied each time. its a great weight of grease for the bolt. i know what you mean about gbb's though. tried it on my slide rails - way too thick Link to post Share on other sites
matt.bee Posted April 14, 2010 Report Share Posted April 14, 2010 Years as a cycle mechanic gave me a loathing of lithium grease. Flicks off bearings easily, so I suspect if you use it anywhere near the piston it will end up getting blown through the air nozzle onto the hop rubber. Seeized seatposts or pedals caused by galvanic corrosion have also put me off. Annything designed to be used anywhere near cycle or motorbike suspension systems or the like will be specifically designed to be plastic and rubber safe as these applications have lots of oil and dust seals. Link to post Share on other sites
The General Posted April 15, 2010 Report Share Posted April 15, 2010 Halfords Finish line teflon grease Finish line ceramic grease Google them both for UK stores, Halfords also sells them This, I have been recommending the above for quite some time. Strangly some people still use Lithium or silicone based grease in AEG's. Makes no sense to me at all. Lithium is junk, I have seen it dry and become crumbly in mechboxes and silicone is no where near as effective as the Teflon series from Finish Line. Link to post Share on other sites
greg Posted April 15, 2010 Report Share Posted April 15, 2010 fair enough, but i use it on my bolty, which gets stripped down every couple of months at least, so gets re-applied each time. its a great weight of grease for the bolt. Agreed. What works on an aeg, is not necessarily the best for a bolty & vice-versa. After years of using abbey 35 in my vsrs, (which had to be re applied every 200 shots), I tried the Finnish line Teflon stuff that the General recommends. It is excellent in aegs, & works well as a lube in bolties, giving a very smooth bolt pull for over a thousand shots. & it doesn't dry up. But be warned, it is not Lalax friendly. It unfortunately wrote off one of my zero pistons! The nylon bushes sort of eroded & the rubber pad on the front fell off & curled up. I'm currently using abbey silicon grease on the vsr's & it seems to work very well. As yet, I've put about 600 shots through & the bolt is still silky smooth. Only time will tell if it drys out. I wouldn't recommend it for aeg cylinders, as I doubt it would last long. On a side note, the Systema cylinder grease is excellent, but costs an arm for a thimble full. It also has a very sobering advisory statement on the back of the packaging, stating that Systema requires users to clean & re grease their cylinders at the end of each day of use or 2000 shots, whichever comes first. Greg. Link to post Share on other sites
Crimson Posted April 15, 2010 Report Share Posted April 15, 2010 Lazy work done: http://www.probikekit.com/display.php?code=A8017 & http://www.probikekit.com/display.php?code=NP08607 Use the ceramic on the gears and the pistons groves then use the teflon on the inside of the cylinder and o ring ! Link to post Share on other sites
Jamanyar Posted April 16, 2010 Report Share Posted April 16, 2010 Thanks Crimson, Just ordered some!! J. Link to post Share on other sites
Recommended Posts
Archived
This topic is now archived and is closed to further replies.