famman47 Posted June 14, 2006 Report Share Posted June 14, 2006 tried to fit in a 6mm bearing but the axis doesnt fit the axis if the mp7 gears is nearly 2.5mm, normal aegs gear is 3mm axis <{POST_SNAPBACK}> I wonder what kind of shims to use, if more are needed, when doing a bushing upgrade--standard ones, like would be used for other 6mm bushings? Since the gear axle is a bit smaller diameter than that on full size aeg gears, I suppose regular shims would be prone to more lateral movement when used with mp7 gears, but would this cause any problem? Has anyone reading this replaced their bushings and also had to add a few additional shims in the process? If so, what kind of shims worked? Link to post Share on other sites
Rapier Posted November 22, 2006 Report Share Posted November 22, 2006 Sorry for resurecting such an old thread, but I'm going to be putting a TB barrel in my MP7 and I'm still not sure how to get the barrel out and I don't want to open it blindly Do I need to remove the entire gearbox to get it out or does it come out threw the front some how? Link to post Share on other sites
Shard Posted November 22, 2006 Report Share Posted November 22, 2006 Hi Rapier, yes you will need to remove the gearbox via the normal strip down method for getting to the gearbox, then the hop unit / barrel assembly just slides out the back after you remove the gearbox Link to post Share on other sites
Rapier Posted November 22, 2006 Report Share Posted November 22, 2006 Thanks much! Now, before I get into it, does it use a standard hop up sleave or does it have a special one? Link to post Share on other sites
Shard Posted November 23, 2006 Report Share Posted November 23, 2006 A special one unfortunately, as far as I can remember (I haven't had mine open in months!). Link to post Share on other sites
moutwtrng Posted December 15, 2006 Report Share Posted December 15, 2006 quick question. On the re-assembly is there a gear timing involed before closing up the gearbox like the regular AEG gearboxes? Link to post Share on other sites
Shard Posted December 15, 2006 Report Share Posted December 15, 2006 No, and there isn't in a regular AEG either - there is no such thing as gear timing Link to post Share on other sites
moutwtrng Posted December 16, 2006 Report Share Posted December 16, 2006 No, and there isn't in a regular AEG either - there is no such thing as gear timing <{POST_SNAPBACK}> Oh I dont really know what to call it but anyway how bout this "sector gear positioning" better? Anyway, So your saying when you re-assemble a regular AEG gearbox you dont have to put the metal column sticking out of the sector gear (the one that makes the tappet plate go back and forth) to the 1 o'clock position. I know for a fact that if you dont do that it will cause your gearbox to jam up. - Link to post Share on other sites
Docv400 Posted December 16, 2006 Report Share Posted December 16, 2006 As long as the pin that actuates the tappet plate is forward (i.e. out of the way of the tappet plate) when you assemble the gearbox, it'll be fine. Link to post Share on other sites
Evil Peter Posted March 19, 2007 Report Share Posted March 19, 2007 Help me, please. It ain't show up those pictures. I really need them, becouse my lovely MP7 broked up and I need help for opening mechbox. By the way problem in my MP7 is it ain't get any power from battery. So it ain't make any noise when i pull tricker. Thank you - Peter Edit: Srry for bumping this theard. (Didin't know this were so old. I gotted here by link) Link to post Share on other sites
suadiablo Posted April 10, 2007 Report Share Posted April 10, 2007 gunner, i think your photo links are not working.. i cant see any pictures anymore.. please help to put them up again.. i wanna try to disassemble my mp7 soon.. thanks! Link to post Share on other sites
The Dot Posted May 4, 2007 Report Share Posted May 4, 2007 I want this guide too... Anyone saved this guide? If yes zip it and post the rapidshare or whatever link... Why we can't see the images anymore??? If anyone knows a similar mechbox dissasembly guide would help very much... Link to post Share on other sites
The Dot Posted May 16, 2007 Report Share Posted May 16, 2007 BUMP!!! Sry but I need this guide. If anyone has a link for a similar link please post it. Else anyone that had an account when this was written please try archive.org! Got there put this topics address and see if you can login and see the pix... If yes save the whole guide and upload it somewhere so everyone can have this... Here Link to post Share on other sites
caveman Posted May 16, 2007 Report Share Posted May 16, 2007 I PMed the author yesterday and he said he re-loaded the images but they still weren't showing up. I checked, and if I tried opening the images up in a new window (by copying the link from "get info" and pasting it into the address bar) they showed up fine. So I think the problem is something changed on the Arnies forums that is causing the images not to load. (They do load rather slow.) So it's a pain, but you can make it work. Link to post Share on other sites
The Dot Posted May 16, 2007 Report Share Posted May 16, 2007 I rebuild it for all you out there! Here we go! out of box the other side of the gun first removing the muzzel, by pressing this botton and pull the muzzel forward done removing the front sight by loosening this screw remove the top rail by loosening 3 screws This is a fake screw, dont touch it. see everything inside removing the bolt spring like this, dont let it bounce away!! Link to post Share on other sites
The Dot Posted May 16, 2007 Report Share Posted May 16, 2007 spring removed pull out the wires remove this screw remove the 2 rear pins pull it out removing the butt stock push this silvery tab take it out also and take out the gearbox fixture push the wire into the receiver, and take out the gear box. Link to post Share on other sites
The Dot Posted May 16, 2007 Report Share Posted May 16, 2007 done!! this tiny gearbox just have 4 screws. exploded. comparison of a full size cylinder and the mp7 cylinder, and full size sector gear, cutie!! full size piston and mp7 piston here. Link to post Share on other sites
The Dot Posted May 16, 2007 Report Share Posted May 16, 2007 Phewwww! Please check for errors. I double checked but you never know... And if possible for a mod please fix this topic so it's easy for someone to find the posts with the working pix... EDIT: I think that the original author must be mentioned in my first post or in all posts. I can't edit them so if a mod wants to do it it would be nice. THE CREATOR OF THIS GUIDE IS "gunner-airsoft". I only fixed the broken images... Link to post Share on other sites
Solscud007 Posted December 16, 2007 Report Share Posted December 16, 2007 Phewwww! Please check for errors. I double checked but you never know... And if possible for a mod please fix this topic so it's easy for someone to find the posts with the working pix... EDIT: I think that the original author must be mentioned in my first post or in all posts. I can't edit them so if a mod wants to do it it would be nice. THE CREATOR OF THIS GUIDE IS "gunner-airsoft". I only fixed the broken images... thank you for going thru all that work. I appreciate it. Link to post Share on other sites
greg Posted December 16, 2007 Report Share Posted December 16, 2007 Dat reminds me,,,,,,,,,,,,,,,,,,,,,Now where did I put those bits. Greg. Link to post Share on other sites
dr_pepper_lover_airsoft Posted December 17, 2007 Report Share Posted December 17, 2007 braver than me, ive just spent 2 hours looking for a spring, from now on im gonna strip my weapons inside a a box, in the dark with the lid shut, the best option i think! lol Link to post Share on other sites
babuka Posted May 11, 2008 Report Share Posted May 11, 2008 Anyone would be so kind to provide info regarding original TM MP7 motor? What kind of motor is it generally? Does it has any markings on it? What is accurate dimensions of it? If we can identify what kind (class, type) of motor TM have used plus proper measurements of the motor - we can find a replacement in case it is needed (or even a better one with the same size). Thank you! Link to post Share on other sites
tom_clancy84 Posted January 8, 2009 Report Share Posted January 8, 2009 what? where are the pictures? Link to post Share on other sites
alexishere2008 Posted January 9, 2009 Report Share Posted January 9, 2009 wow.. this is an old thread... Link to post Share on other sites
yeatzee Posted January 13, 2009 Report Share Posted January 13, 2009 well since its revived I need some help. For what ever reason my mp7 has stopped feeding bbs. Whats wrong, and how do I fix it? My standards dont feed at all......and my highcaps feed very rarely......and when it does its at a really slow fps. I've attempted to get to the gearbox and have done everything right to strip it down but it wont slide out.....its like its caught on something or idk it just wont slide out. Help would be appreciated Link to post Share on other sites
Recommended Posts
Archived
This topic is now archived and is closed to further replies.