BioRage Posted June 6, 2015 Report Share Posted June 6, 2015 I really like the nova. Thanks! (Prefer over atei ) 1 Quote Link to post Share on other sites
cav. Posted June 13, 2015 Report Share Posted June 13, 2015 (edited) Hm actually having some cycling issues atm. Think the nozzle is getting caught at times, will have to tinker with it. Right now just slapped stock nozzle in, will see how it games tomorrow! Edited June 13, 2015 by cav. Quote Link to post Share on other sites
DeltaZero Posted June 13, 2015 Author Report Share Posted June 13, 2015 Not having any cycling issues with mine. It could be the screw that goes through the nozzle to hold the floating valve in place.. Make sure that is loctited and secure. I didn't loctite it at first and it unscrewed slightly and cause jamming. I haven't gotten round to modding the UAC hammer parts yet either unfortunately! Quote Link to post Share on other sites
starburst Posted June 13, 2015 Report Share Posted June 13, 2015 I had cycling issues with the stock parts last week,; nozzel seems to get stuck stopping the slide returning to full battery and occasional double feeds (think they may be connected). Added some silicone to the BBU hoping that stops it... now to tackle the leaking magazine! Quote Link to post Share on other sites
cav. Posted June 14, 2015 Report Share Posted June 14, 2015 (edited) Hmmm I noticed racking it, there are times where it stops and cannot return! Slide catch is not engaged. Dunno what is going on T___T When i gamed it today, it would not fully return, and Id have to push it and it works! Sometimes no problems though :l Edited June 14, 2015 by cav. Quote Link to post Share on other sites
gogojuice Posted June 14, 2015 Report Share Posted June 14, 2015 I'm having cycling issues too. Cav.. thanks for the updates.. From what your describing.. I have the same thing. No idea what the solution is yet I won't have time to look at it for the next little while, but I'll keep looking at these posts. Cheers Quote Link to post Share on other sites
cav. Posted June 14, 2015 Report Share Posted June 14, 2015 Switched back to stock BBU and nozzle, just from racking nothing is getting caught. Will trying shooting it tomorrow and see what happens! Quote Link to post Share on other sites
gogojuice Posted June 14, 2015 Report Share Posted June 14, 2015 Mine is all stock... when I rack.. all is fine now. However... I still have the same problems of double feeds (Occasionally) and more often it doesn't complete the cycle. I just need to nudge the slide forward. Quote Link to post Share on other sites
cav. Posted June 14, 2015 Report Share Posted June 14, 2015 Mine is all stock... when I rack.. all is fine now. However... I still have the same problems of double feeds (Occasionally) and more often it doesn't complete the cycle. I just need to nudge the slide forward. Very strange! I didnt have any problems with stock setup Quote Link to post Share on other sites
DeltaZero Posted June 14, 2015 Author Report Share Posted June 14, 2015 That's very strange all of you.. My complete upgraded M&P is having no issues. Are you sure you've got the BBU low enough into the slide. Are the runners flush? Quote Link to post Share on other sites
BioRage Posted June 14, 2015 Report Share Posted June 14, 2015 You running alum nozzle delta? Cav is. Quote Link to post Share on other sites
cav. Posted June 15, 2015 Report Share Posted June 15, 2015 That's very strange all of you.. My complete upgraded M&P is having no issues. Are you sure you've got the BBU low enough into the slide. Are the runners flush? Not sure, I hammered it down so it's gotta be sitting low. Will need to do some further testing! Quote Link to post Share on other sites
DeltaZero Posted June 15, 2015 Author Report Share Posted June 15, 2015 You running alum nozzle delta? Cav is. Other than the UAC trigger parts mine has everything you can put in it. It'll have the trigger parts tomorrow should all go to plan! Not sure, I hammered it down so it's gotta be sitting low. Will need to do some further testing! Strange indeed. Did you actually hammer it down?? You may have actually misshaped the BBU if you actually hammered it? :/ Quote Link to post Share on other sites
cav. Posted June 15, 2015 Report Share Posted June 15, 2015 Other than the UAC trigger parts mine has everything you can put in it. It'll have the trigger parts tomorrow should all go to plan! Strange indeed. Did you actually hammer it down?? You may have actually misshaped the BBU if you actually hammered it? :/ Let's say gently hammered it down, only the rear area as it was more solid Quote Link to post Share on other sites
DeltaZero Posted June 15, 2015 Author Report Share Posted June 15, 2015 Ah I see.. and the guide rails are nice and smooth? Try the BBU without a nozzle installed see if it gets caught still.. If not try manually cycling it over and over for 20 mins or something.. I removed the spring and just cycled the slide to get it nice and smooth and wear the new parts in. Quote Link to post Share on other sites
kesuki1027 Posted June 18, 2015 Report Share Posted June 18, 2015 Hi! To the Nova slide owners (10-8 if it matters), how different is the blowback vs. the original TM slide? Is it as snappy? Quote Link to post Share on other sites
DeltaZero Posted June 18, 2015 Author Report Share Posted June 18, 2015 I have the silver Nova slide. It's just as snappy. With the slightly added weight it almost seems to kick more. Really is very nice. Sent from my iPad using Tapatalk HD Quote Link to post Share on other sites
cav. Posted June 18, 2015 Report Share Posted June 18, 2015 (edited) Gamed the gun again yesterday. Detonator slide, with the stock nozzle and BBU, still not cycling properly. Getting a headache -.- Will take video! Edited June 18, 2015 by cav. Quote Link to post Share on other sites
BioRage Posted June 18, 2015 Report Share Posted June 18, 2015 Gamed the gun again yesterday. Detonator slide, with the stock nozzle and BBU, still not cycling properly. Getting a headache -.- Will take video! Should of cycled with my 150% spring, I think it may of been a lot better :S. Quote Link to post Share on other sites
cav. Posted June 18, 2015 Report Share Posted June 18, 2015 Should of cycled with my 150% spring, I think it may of been a lot better :S. Still got stuck when it racked to the back. The slide catch didnt even engage :c Quote Link to post Share on other sites
mrsevenstars Posted June 18, 2015 Report Share Posted June 18, 2015 Did you fully tighten the allen screw that holds the faux extractor? I noticed my guns performance is alittle wonky if the extractor cant move freely. I usually go a turn off of full tight. I had this on all of my detonator m&p9 slides Quote Link to post Share on other sites
cav. Posted June 19, 2015 Report Share Posted June 19, 2015 (edited) Did you fully tighten the allen screw that holds the faux extractor? I noticed my guns performance is alittle wonky if the extractor cant move freely. I usually go a turn off of full tight. I had this on all of my detonator m&p9 slides Yep, I thought it was that too! But it isnt >< Edited June 19, 2015 by cav. Quote Link to post Share on other sites
thatguy404 Posted June 19, 2015 Report Share Posted June 19, 2015 Having an issue with x2 new mags I have for the M&P. I've had them awhile and tried running them in but still having issues with them. (Also they have more of a MATT finish, than the original supplied batch, my M&P was one of the first in the UK) Essentially the BB's are getting stuck in the follower on the way up to the feed lip.Tried using a different brands of bb's etc. But still the same issue with these x2 newer mags.Any ideas? Tried a general strip clean and lube to no avail Quote Link to post Share on other sites
mrsevenstars Posted June 19, 2015 Report Share Posted June 19, 2015 Cav I also had one of them kinda let the BBU misalign in the slide so i have to remove and reinstall then i cycled with the stock recoil spring. I also use a glock upgraded recoil spring now in my m&ps and the cycle fine. Hope that helps and you get it sorted out. 1 Quote Link to post Share on other sites
DeltaZero Posted June 19, 2015 Author Report Share Posted June 19, 2015 A glock recoil spring?? Interesting I might try it! Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.