lacanuck24 Posted July 20, 2012 Report Share Posted July 20, 2012 I couldn't resist. Now I just have to sell enough stuff to pay for these parts plus a P* setup. 1 - 18inch Barrel 1 - Long Black Handguard 1 - Harris Style RIS Bipod 3 - RIS Panels 1 - 51T Black CCW Mock Supressor with Flash Hider 1 - Modify 650mm 6.03 Inner Barrel Personally I'd go with a 6.01inner barrel, for me I saw a difference with the 6.03. I don't think the 650mm will fit even with suppressor, or just barely. I'm running a 460mm if I remember right and I'm just short of the end of the outer. Which 51T flash hider are you going for? The M.I.T.E.R or the Ratchet? Either way I don't think a 650mm will work. The MITER's threads are about in the middle of the flash hider so you're losing a few cm's off the bat. I could be wrong though about the length Quote Link to post Share on other sites
Seraph01 Posted July 20, 2012 Report Share Posted July 20, 2012 let me know if that suppressor makes it through customs Quote Link to post Share on other sites
Hans17 Posted July 20, 2012 Report Share Posted July 20, 2012 Personally I'd go with a 6.01inner barrel, for me I saw a difference with the 6.03. I don't think the 650mm will fit even with suppressor, or just barely. I'm running a 460mm if I remember right and I'm just short of the end of the outer. Which 51T flash hider are you going for? The M.I.T.E.R or the Ratchet? Either way I don't think a 650mm will work. The MITER's threads are about in the middle of the flash hider so you're losing a few cm's off the bat. I could be wrong though about the length 6.01 is too tight for todays bb's. I don't remember where the article is but to shorten it up .03 mm is the perfect sweetspot for a cushion of air around the bb in a barrel. Bb's earlier on in airsoft were made 5.98mm and now they are 6.00mm most times so 6.03 is the new 6.01. As for the length. I wanted PSG-1 length so I did the math 18 inch outer barrel plus 8.5 inch suppressor = 26.5 inches covered, 650mm = 25.5 inches. So I should get it all covered with 1 inch of suppressor. I might end up putting a 490mm barrel in instead so I can run without a suppressor and so the suppressor actually suppresses by having to run through the foam outside of the inner barrel instead of just leading right out the opening. Quote Link to post Share on other sites
Hans17 Posted July 20, 2012 Report Share Posted July 20, 2012 let me know if that suppressor makes it through customs I don't see any reason it wouldn't. It says for airsoft use only on it and is actually licensed through AAC. Quote Link to post Share on other sites
lacanuck24 Posted July 20, 2012 Report Share Posted July 20, 2012 (edited) As for the length. I wanted PSG-1 length so I did the math 18 inch outer barrel plus 8.5 inch suppressor = 26.5 inches covered, 650mm = 25.5 inches. So I should get it all covered with 1 inch of suppressor. I might end up putting a 490mm barrel in instead so I can run without a suppressor and so the suppressor actually suppresses by having to run through the foam outside of the inner barrel instead of just leading right out the opening. When it comes to barrel ID, to each his own. I was hesitant to go 6.01, but its working wonders vs a 6.03 Far as your plan goes for length keep in mind that with the 51T MITER threaded flash hider will pull the suppressor back 60-65mm. I'm short siding the number. This pic should clear things up. The length in the photo is about 635-640mm, but take into account that my flash hider is clockwise threaded, so its not even threaded on which means theres about 8-10mm of extra length there, so somewhere in the 630mm total length, or 25". Think real hard about the 490mm, or use a different, longer suppressor cause the AAC's ain't gonna fit Edited July 20, 2012 by lacanuck24 Quote Link to post Share on other sites
Hans17 Posted July 20, 2012 Report Share Posted July 20, 2012 I love the AAC and paid $85 for it so I think a different barrel will have to do or a external barrel extension. Then I still get 650mm and full suppression but a HUGE gun. Maybe something smaller would perform just as good and be more comfortable. You should do a shooting comparison between 6.01 and 6.03 for us Quote Link to post Share on other sites
Hans17 Posted July 20, 2012 Report Share Posted July 20, 2012 Really not excited about inner barrel sticking out an inch even after paying tons of money for a outer barrel and extension lol Quote Link to post Share on other sites
Milspec Mikey Posted July 20, 2012 Report Share Posted July 20, 2012 Hey, thanks for clearing that up, lacanuck! Might have saved some people some time and money. Quote Link to post Share on other sites
snake_pliskin Posted July 20, 2012 Report Share Posted July 20, 2012 AEG units that I have has half or more than an inch or two sticking out and all with AAC BlackOut. no big deal for me. im not for the photo ops, im just maximizing what the AAC flash hider can do for me. Quote Link to post Share on other sites
Hans17 Posted July 20, 2012 Report Share Posted July 20, 2012 I don't mind how it really looks sticking out the end but I put my silencer on to actually silence the PolarStar down to almost nothing lol So I don't want the inner running right through it or it doesn't do it's job. Also after thinking further on it 6.01s are TBB for gbbrs so would work better with the polarstar and the 6.03s are perfect for AEGs Quote Link to post Share on other sites
hmg9194 Posted July 21, 2012 Report Share Posted July 21, 2012 I couldn't resist. Now I just have to sell enough stuff to pay for these parts plus a P* setup. 1 - 18inch Barrel 1 - Long Black Handguard 1 - Harris Style RIS Bipod 3 - RIS Panels 1 - 51T Black CCW Mock Supressor with Flash Hider 1 - Modify 650mm 6.03 Inner Barrel Unless you are running the polarstar In this setup, you shouldn't get that barrel. Really nothing over 400 mm helps unless it's a gas setup. It's common knowledge that 6.03 provides better accuracy and range than 6.01, the quality matters more. I only get PDI, edgi or Prometheus. Mad bull if I'm feeling poor. Quote Link to post Share on other sites
Hans17 Posted July 21, 2012 Report Share Posted July 21, 2012 Unless you are running the polarstar In this setup, you shouldn't get that barrel. Really nothing over 400 mm helps unless it's a gas setup. It's common knowledge that 6.03 provides better accuracy and range than 6.01, the quality matters more. I only get PDI, edgi or Prometheus. Mad bull if I'm feeling poor. Planning to throw a polarstar into it indeed. I've heard the longest barrel possible with a good hop up is the way to go. Modify barrels are quite impressive in my opinion. I've seen 3 different instances of the range and accuracy improved by different players using them on the field. Quote Link to post Share on other sites
IBMedic Posted July 24, 2012 Report Share Posted July 24, 2012 Sorry if this question has been asked, but I didn't want to go through 124 pages, and also some of that may have been based on older production lots of the rifle. I've wanted to get this rifle for a while but have held off because it's an Ares, and because of the problems with the hopup. Has anyone bought a new model lately and can tell me whether the hopup issue at least has been fixed? Also, internally, is it still plastic bushings and other crappy Ares stuff or is it a fairly reliable setup now? Quote Link to post Share on other sites
Hans17 Posted July 24, 2012 Report Share Posted July 24, 2012 Sorry if this question has been asked, but I didn't want to go through 124 pages, and also some of that may have been based on older production lots of the rifle. I've wanted to get this rifle for a while but have held off because it's an Ares, and because of the problems with the hopup. Has anyone bought a new model lately and can tell me whether the hopup issue at least has been fixed? Also, internally, is it still plastic bushings and other crappy Ares stuff or is it a fairly reliable setup now? I don't know of anyone who owns one who has had hopup problems including myself. And the bushings are metal. Hope that helped Quote Link to post Share on other sites
Gazw Posted July 24, 2012 Report Share Posted July 24, 2012 I had no hop up whatsoever until I changed the bucking to madbull blue which gave great results. Also glued a small piece of plastic coated wire in the fig-8 nub (as per toothpick mod) to strengthen it, which I think has also helped. Quote Link to post Share on other sites
Hans17 Posted July 24, 2012 Report Share Posted July 24, 2012 I had no hop up whatsoever until I changed the bucking to madbull blue which gave great results. Also glued a small piece of plastic coated wire in the fig-8 nub (as per toothpick mod) to strengthen it, which I think has also helped. Planning to run a modify hybrid barrel and bucking not sure how to do toothpick mod though. Quote Link to post Share on other sites
ODST_NE0 Posted July 24, 2012 Report Share Posted July 24, 2012 I think most people who have bought an ACR, have replaced the bucking with one that works (I used a G&G). Although in general a lot of people will replace their hop up buckings as a standard upgrade. It is a very easy thing to do, especially with the ACR quick barrel changing feature. Quote Link to post Share on other sites
Mad-Larkin Posted July 29, 2012 Report Share Posted July 29, 2012 (edited) hey all, i picked up an akm masada today and am loving it! Had a touch of trouble with the hop tho. The 8 nub was mashed backwards where the quickchange barrel had pushed in. It was messing up the airseal so fps was all over the place. I reinforced the nub by finding a o-ring of about the same size and cutting 2mm out of it and sliding it into the hole. However now when i push the barrel in it still forces the hop nub backwards. I had to remove the whole unit, take the bit that holds the nub out the top, secure the barrel, then reseat the nub back down onto the bucking. Anyone else had this issue? seems like the nub won't slide over the top of the bucking to seat over the hole, which basically means the quick swap barrel cannot be swapped. Is the nub maybe too mashed? if so, where can i get a new one? My reinforcing also seems to have given me loads of hop, even off, my .25's were arcing up :/ Edited July 29, 2012 by Mad-Larkin Quote Link to post Share on other sites
Mad-Larkin Posted July 29, 2012 Report Share Posted July 29, 2012 and the gun uses regular springs? The one i got in there atm has been cut down about an inch shorter than the sp90 i got here. Just wanted to make sure it wasn't like the tm recoils with shorter springs. Quote Link to post Share on other sites
Seraph01 Posted July 30, 2012 Report Share Posted July 30, 2012 Did you buy this gun second hand? Double check that you have the hop off when reinstalling, and is that o ring that you put in so thick that maybe it caused the nub to stick down farther? Quote Link to post Share on other sites
Mad-Larkin Posted July 30, 2012 Report Share Posted July 30, 2012 (edited) Ah right, I was under the impression that I should fill the 8nubs hole? Should I still be leaving it some movement room? The diameter of the o-ring is pretty much exactly the same size as the hole so it's solid lol I'll try a smaller one tonight. Cheers! Edited July 30, 2012 by Mad-Larkin Quote Link to post Share on other sites
Seraph01 Posted July 30, 2012 Report Share Posted July 30, 2012 filling in the hole has been done by many and even by myself. I was just checking to see if you had taken that into account. If this is a second hand gun, I would replace the hop bucking and buy a new spring and take hop up apart again just to make sure that nothing is damaged from the previous owner. Quote Link to post Share on other sites
Mad-Larkin Posted July 30, 2012 Report Share Posted July 30, 2012 Well, i've stripped it all again, except for the nub being a little mashed it all looks good. am gonna get new bucking though, which are people finding works the best? I've taken the filling out completely now, and my bb's seem to still be rising up even with the hop fully off :/ Anyone else had this issue? Got the new spring already, but i don't have a chrono so going to leave it as is till i get on site and can have a tweak. THanks for ideas seraph Quote Link to post Share on other sites
V3RTIGO Posted July 31, 2012 Report Share Posted July 31, 2012 hey all, i picked up an akm masada today and am loving it! Had a touch of trouble with the hop tho. The 8 nub was mashed backwards where the quickchange barrel had pushed in. It was messing up the airseal so fps was all over the place. I reinforced the nub by finding a o-ring of about the same size and cutting 2mm out of it and sliding it into the hole. However now when i push the barrel in it still forces the hop nub backwards. I had to remove the whole unit, take the bit that holds the nub out the top, secure the barrel, then reseat the nub back down onto the bucking. Anyone else had this issue? seems like the nub won't slide over the top of the bucking to seat over the hole, which basically means the quick swap barrel cannot be swapped. Is the nub maybe too mashed? if so, where can i get a new one? My reinforcing also seems to have given me loads of hop, even off, my .25's were arcing up :/ I'm sorry to tell you, but you have screwed your hop up. As with any barrel removal, you ALWAYS have to adjust the hop to zero. that way, the will be very very minimal contact between the nub and the bucking. I recommend this: http://www.wiitech.com.hk/eshop/product_info.php?cPath=68&products_id=430 or you can order a new nub from magpul or firesupport.co.uk or do that wierd toothpick mod. next time you remove the barrel, make sure that you zero the hop (just turn the hop up wheel clockwise). Quote Link to post Share on other sites
Mad-Larkin Posted July 31, 2012 Report Share Posted July 31, 2012 Thought so, its second hand and came that way :/ fire support are out of stock at the moment so may look into that wiitech thing. How would I go about ordering direct from magpul? Cheers for info Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.