GingaNinga Posted January 6, 2011 Report Share Posted January 6, 2011 Sadly, the valve head snapped, so I have to get a replacement valve. Can you link to the video? Quote Link to post Share on other sites
Riko Posted January 6, 2011 Report Share Posted January 6, 2011 Lol that vid wont help, it was just to state that probably nothing was wrong in the first place..... But since it snapped you will have to replace Quote Link to post Share on other sites
bankz5152 Posted January 6, 2011 Report Share Posted January 6, 2011 Wow it snapped? Ive unscrewed mine over and over in and out not even a stratch. Really supprised on that. If need be the valves from most 40mm grenades also fit the G39 mags. Managed to fix all the leaks in my mags but adding some gearbox silicone grease. Quote Link to post Share on other sites
kruck Posted January 6, 2011 Report Share Posted January 6, 2011 Miss my posts earlier about not tightening the fill valves? The valve you linked to is the one to get if you've snapped yours too, I've broken 2 so far and pre-emptively replaced a 3rd. The hornbill fill valves are really strong & don't leak. Quote Link to post Share on other sites
danielsilva Posted January 6, 2011 Report Share Posted January 6, 2011 This isn't a new issue and is a problem that comes back from the old v1 M4 mags. Just a tad more torsion on the fill valve and there goes it's head. I've been using co2/green grenade valves to replace them, much stronger and are ready for much bigger pressures. Quote Link to post Share on other sites
nickthebrick65 Posted January 7, 2011 Report Share Posted January 7, 2011 (edited) Converted my G39c Full size G36 with K barrel and AG36 launcher, flat top carry handle, and Acog 4x replica with Docter sight. Edited January 7, 2011 by nickthebrick65 Quote Link to post Share on other sites
bankz5152 Posted January 7, 2011 Report Share Posted January 7, 2011 Looks bad *albatross*! One question, did you take the WE G39C sticker off before you put the HK G36C sticker on? Quote Link to post Share on other sites
nickthebrick65 Posted January 7, 2011 Report Share Posted January 7, 2011 No I didn't, when I put it on I didn't know the damn thing came off, so I tried to remove the HK one, and it'll tear apart if I do that. So I guess I have to leave as is, I know it's a little lifted in some parts. Quote Link to post Share on other sites
Riko Posted January 7, 2011 Report Share Posted January 7, 2011 Hm, before i put my sticker on I didnt remove anything either and it doesnt look lifted at all....strange Quote Link to post Share on other sites
4boost Posted January 7, 2011 Report Share Posted January 7, 2011 Converted my G39c Full size G36 with K barrel and AG36 launcher, flat top carry handle, and Acog 4x replica with Docter sight. Who makes the rail and how does it fit? Quote Link to post Share on other sites
nickthebrick65 Posted January 7, 2011 Report Share Posted January 7, 2011 Leapers makes the rail. Its a very tight fit and had to be tapped into place with a rubber mallet. One of the holes was a bit off as well, but was easily solved with a drill by widening the hole. Quote Link to post Share on other sites
Spencerman Posted January 7, 2011 Report Share Posted January 7, 2011 My original WE sticker was a little bit lifted in places, but I am not complaining, as for me that was a plus point. It stayed on the gun for about 2 minutes, only because I had to remove the little 'made in...' sticker on the grip first! One thing that I was surprised at was that mine came with the protective film still on the sticker, giving it a really shiny and poorly applied kind of look, I was surprised at that, not that I think that was bad, but just that I wasnt expecting it. There may be other people out there who dont realise that the WE 'sticker' has a protective film over the top, thus making it shinier than it should be! Also I must say just how awesome the finish on this gun is. Having had a few G36 AEGs I was expecting the plastic/polymer whatever to feel similar. How wrong I was. The finish on the WE is so much better, is so good, so much closer to the real gun that I was bowled over. Shame that they have the wrong shape butt plate (wrong compared to the ones that I have seen) and that they have a bullet missing on the selector switch, but that is really minor nit poicking. I only got mine out of customs this evening, so have not had a chance to fire it, but from the rest of the gun I am really looking forward to it. Now, if only WE would release some mags with the dummy bullets in (the internal casting shaped that way) then that would be great, although I wouldnt want them to replace the mags that they have, just give people the choice. I like 'not' seeing the bullets sometimes also, even if they did it like a half empty mag where you can only see the first few bullets, that would be something different. Quote Link to post Share on other sites
Riko Posted January 7, 2011 Report Share Posted January 7, 2011 My original WE sticker was a little bit lifted in places, but I am not complaining, as for me that was a plus point. It stayed on the gun for about 2 minutes, only because I had to remove the little 'made in...' sticker on the grip first! One thing that I was surprised at was that mine came with the protective film still on the sticker, giving it a really shiny and poorly applied kind of look, I was surprised at that, not that I think that was bad, but just that I wasnt expecting it. There may be other people out there who dont realise that the WE 'sticker' has a protective film over the top, thus making it shinier than it should be! Also I must say just how awesome the finish on this gun is. Having had a few G36 AEGs I was expecting the plastic/polymer whatever to feel similar. How wrong I was. The finish on the WE is so much better, is so good, so much closer to the real gun that I was bowled over. Shame that they have the wrong shape butt plate (wrong compared to the ones that I have seen) and that they have a bullet missing on the selector switch, but that is really minor nit poicking. I only got mine out of customs this evening, so have not had a chance to fire it, but from the rest of the gun I am really looking forward to it. Now, if only WE would release some mags with the dummy bullets in (the internal casting shaped that way) then that would be great, although I wouldnt want them to replace the mags that they have, just give people the choice. I like 'not' seeing the bullets sometimes also, even if they did it like a half empty mag where you can only see the first few bullets, that would be something different. you can download a pdf file with dummy bullets for your mag....its posted here somewhere Quote Link to post Share on other sites
Spencerman Posted January 8, 2011 Report Share Posted January 8, 2011 Yes, I have that, but I meant that the inner casting would be slightly rippled to look as if there were bullets there, so that the light catches them differently at different angles. The pictures are ok, and I recon that it is a great idea and excellent that people are prepared to take the time and trouble to do that for everyone. I didnt think that it would be realistic to do dummy bullets in a gas mag, but as the gas is enough to last for 3 mags or so according to people who have had the chance to fire theirs (I cant firemine until tomorrow, the suspense is killing me!), I know that it is realistic to sacrifice soem of that storage space to give a dummy bullet look. The amount of ammo wount be affected at all, as 30 rounds is not much at all, so it would only affect the gas chambers if I am understanding it right? SRC I believe it is are working on a mag with dummy bullets for their version when it finally comes out. I am sure that it would be easy for WE to make one, and the extra cost shouldnt be a lot more, there is obviously a little bit more metal needed to be used to form the shape of the bullets, but that is nominal, then there is the time and cost to paint the bullets, but again it is not exactly impossible super huge costs. The biggest cost would probably be the cost to set up the tooling to make the casts of the dummy bullets shape internals. Failing that, just make the internals slimmer and pop in a row of plastic dummy bullets, just like the TM low caps. It wouldnt be for everyone, some people prefer the original look of the mag, but choice is always great, and I am sure that it would sell like hot cakes. I for one would have a few of each, although I would probably choose the dummy bullet version first. Quote Link to post Share on other sites
muffe66 Posted January 8, 2011 Report Share Posted January 8, 2011 Hum anyone that knows if the plastic flippy thing on the charging handel is based on Realsteel or Airsoft? mine snapped and i am looking for a replacment Quote Link to post Share on other sites
muffe66 Posted January 8, 2011 Report Share Posted January 8, 2011 (edited) remove Edited January 8, 2011 by muffe66 1 Quote Link to post Share on other sites
Riko Posted January 8, 2011 Report Share Posted January 8, 2011 Hum anyone that knows if the plastic flippy thing on the charging handel is based on Realsteel or Airsoft? mine snapped and i am looking for a replacment you can try to mail WE for a replacement part.....I did mail WE + airsoftglobal for another part but We didnt reply since a few days ago and I had to contact airsoftglobal within 7 days from now for a update and I started mailing them before christmas... so it seems, parts for the G39 are not common OR WE has really sucky customer service! But I advice to mail both and see wich of us gets our replacement parts first Quote Link to post Share on other sites
muffe66 Posted January 8, 2011 Report Share Posted January 8, 2011 well, iam going to try AEG part from a CA wich is a broken gun. we will see where this will end ^^ Quote Link to post Share on other sites
Reppyboyo Posted January 8, 2011 Report Share Posted January 8, 2011 WE have never been good with spare parts. Quote Link to post Share on other sites
danielsilva Posted January 8, 2011 Report Share Posted January 8, 2011 Never understood that ... i never had any shortage of spare parts. Hell i'll even keep a closed bolt M16 just to not let my huge list of spare parts go to waste But it seems that spare parts specifically for the G36 really is difficult to get. Quote Link to post Share on other sites
Riko Posted January 8, 2011 Report Share Posted January 8, 2011 I dont believe in diffucult I believe in customer service....its all about the willingness to provide that service. This is the last email I got from Alfred the man in charge for spares. Dear **** Sorry for the late reply~ in fact I just received those parts from our Taiwan factory now, cos we have few days holidays right now, so I couldn't arrange an immediate shippment for you right now, I may send it out in next week, so don't worry about that~ I hope you MERRY CHRISTMAS and God Bless you^^ B.rg Alfred WE Tactical Training International James however was always helpful and replied asap on my emails, only he is not in charge of spares.... Quote Link to post Share on other sites
Spencerman Posted January 9, 2011 Report Share Posted January 9, 2011 The CA part might fit, but it will not work properly. The handle has an elongated hole which is a little like a clip fastener, so you can pull the paddle out to whichever side, and then push the paddle toward the opposite side of the gun and it will lock into place. The CA is just a pin through a hole, so it will not push or move at all once it is in, so it will always return to the centre position no matter what you do. You could try using the part from the Ares/Umarex gun, as that is similar so that might work. I also have swapped the buttplate off of a CA gun to give me the correct rounded pad, it fits perfectly, but is really really tight to get on, I had to use the assistance of a screwdriver blade to get it into the groves, but now it is on... Now to sort out the laser engraving and it will be all finished! Quote Link to post Share on other sites
Riko Posted January 10, 2011 Report Share Posted January 10, 2011 Okidoki, I have finally solved my problem of the servere wobbling of my 505mm long inner barrel! So this mod will certainly work with the stock inner barrel as well! The problem is due to repeated assembling and disassembling of the inner barrel. The repeated screwing and unscrewing of setscrew part 125 caused to lose thread at the bottom of part 27. (look at your manuel guys) So it caused my inner barrel assembly to wobble a lot! There are 2 solutions for this: get a new part 27, since this will have new threads. But if you really want to be sure, you can even keep your part 27 but just get a longer setscrew to replace the stock setscrew (part 125) You will have to find a setscrew of the type: M3 - 5mm! (on the picture: the bottom setscrew on is the new one) The stock setscrew length is 3mm. So 5mm is perfect! Any longer than that and you will have to cut the setscrew to get it fit inside the upper receiver. Here is explained visually what this mod actually does: green is the inner barrel itself; the black block is the part that surrounds the inner barrel; blue is the set screw that holds the inner barrel assembly in place; the red shows where the thread has gone, causing the stock setscrew to sit lose! Its a mystery why WE didnt used a longer setscrew! Since I didnt know what kind I had to use, I bought a whole kit: http://www.modelsport.co.uk/index.php?product_id=22817 http://www.roundabouttoys.com/store/product/4752/PD1251-Set-Screw-Set,-EB-K/ So, there ya go, with just a longer set screw you will have NO inner barrel wobble at all! Even when using a long inner barrel! Quote Link to post Share on other sites
Atsalakotos Posted January 10, 2011 Report Share Posted January 10, 2011 (edited) Hey guys, is anyone familiar with any shops in the European Union that carry this? (Except Gunfire.pl) Edited January 10, 2011 by Atsalakotos Quote Link to post Share on other sites
hwagan Posted January 10, 2011 Report Share Posted January 10, 2011 Hey guys, is anyone familiar with any shops in the European Union that carry this? (Except Gunfire.pl) www.airsoftarmoury.co.uk www.wolfarmouries.co.uk Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.