3vi1-D4n Posted February 22, 2010 Report Share Posted February 22, 2010 If it is the narrowing/constriction inside the hop rubber you are referring to then yes. Quote Link to post Share on other sites
aznriptide859 Posted February 22, 2010 Report Share Posted February 22, 2010 ^Gotcha. Though in the meantime I've put it all back together - I did a complete reclean/regrease, so I want to test out the accuracy now before doing something drastic to the hopup. Question though - wouldn't removing that "ring" remove any place the BB would sit along in the chamber? Or does the hopup nub do that? Also got my RF pack in today from -I-; sent me a prototype silencer adapter for it as well. Too bad my silencers aren't with me Quote Link to post Share on other sites
AirSoftNJ Posted February 23, 2010 Report Share Posted February 23, 2010 (edited) ^ Mine is Coming Sometime this week, Does any one know if you can use the KSC RF Nozzle in the KSC Taiwan or you have to use the KWA Version Nozzle for it Edited February 23, 2010 by AirSoftNJ Quote Link to post Share on other sites
3vi1-D4n Posted February 23, 2010 Report Share Posted February 23, 2010 Riptide: If you remove the Constriction on the MP7 its not going to affect if the BB sits in the chamber as the hop up is compensating for it. Even on 0.2g hop level is sufficient to keep the BB sitting in the chamber. The only two guns where the lack of the constriction has made BBs roll out with the hop up on; the AGM M4s and the WE M4. Quote Link to post Share on other sites
aznriptide859 Posted February 23, 2010 Report Share Posted February 23, 2010 Gotcha. I don't have a dremel though, so could I just do this with a small knife? Quote Link to post Share on other sites
3vi1-D4n Posted February 23, 2010 Report Share Posted February 23, 2010 Nah, it won't be as precise as a dremel. I used to do it with a small circular file, but then that could over sand the hop area . With a dremel the holes and even and round and if careful it will not affect the hop. So probably just leave it alone if you can't get a dremel. Quote Link to post Share on other sites
aznriptide859 Posted February 23, 2010 Report Share Posted February 23, 2010 Hmm, gotcha. Are other KWA hopup rubbers the same as the MP7? It looks really familiar to past USP and Glock hopup units I've seen before. Quote Link to post Share on other sites
3vi1-D4n Posted February 23, 2010 Report Share Posted February 23, 2010 I can't say for certain because I haven't tried, but yes they feel and look identical to the default KSC hop rubbers. Quote Link to post Share on other sites
PanteraTigris Posted February 23, 2010 Report Share Posted February 23, 2010 ^ Mine is Coming Sometime this week, Does any one know if you can use the KSC RF Nozzle in the KSC Taiwan or you have to use the KWA Version Nozzle for it RF nozzle is not compatible with KSC "Taiwan" Version or any other version. It is only compatible with the "Japanese" version Quote Link to post Share on other sites
aznriptide859 Posted February 23, 2010 Report Share Posted February 23, 2010 Dang, that sucks , though I really see no need to replace the stock one - my stock KWA is perfectly fine. Quote Link to post Share on other sites
AirSoftNJ Posted February 23, 2010 Report Share Posted February 23, 2010 Bummer I will have to pick up a KWA RF Nozzle then from WGC Quote Link to post Share on other sites
aznriptide859 Posted February 23, 2010 Report Share Posted February 23, 2010 Got my KWA short mag today from ASGI - VERY well built, no trades unlike the KSC, obviously. Can get around 2 mags worth of rounds (~40) per gas charge. IMO look better than with long mags, at least for a pistol use objective. I might order some more Quote Link to post Share on other sites
galactica Posted February 23, 2010 Report Share Posted February 23, 2010 why are people cursing about not being able to replace the KWA nozzle with a readyfighter? It's only the KSC japan model that has the weak cylinder. Quote Link to post Share on other sites
AirSoftNJ Posted February 24, 2010 Report Share Posted February 24, 2010 What Kind of BB's Are You Guys Running in your MP7? Im Debating over .25's and .28's. Im Running a SD Valve, RF Nozzle and 220 EDGI TBB. Any Suggestions on which Weight or What worked best for you Quote Link to post Share on other sites
jotohomomoto Posted February 24, 2010 Report Share Posted February 24, 2010 KWA recommends .25 and thats what I use. I could care less about the fps, I prefer accuracy!!! Quote Link to post Share on other sites
PanteraTigris Posted February 24, 2010 Report Share Posted February 24, 2010 What Kind of BB's Are You Guys Running in your MP7? Im Debating over .25's and .28's. Im Running a SD Valve, RF Nozzle and 220 EDGI TBB. Any Suggestions on which Weight or What worked best for you I'm using KSC .25 and sometimes Madbull .36 and they both work very well. The .36 is very accurate but a diminished range. How did you hide the 220mm inner barrel coz it protrudes way out of the muzzle? Quote Link to post Share on other sites
AirSoftNJ Posted February 24, 2010 Report Share Posted February 24, 2010 Im using a RF Silencer Adapter from -l- With a G&G SS-100, Which BB's are you using .25 and .28s Quote Link to post Share on other sites
FELDJAGER Posted February 24, 2010 Report Share Posted February 24, 2010 G&G .28s have been working well for me; good range and 0 misfeeds. Quote Link to post Share on other sites
3vi1-D4n Posted February 24, 2010 Report Share Posted February 24, 2010 (edited) Anyone managed to get a silencer onto their MP7? Marui thread adaptors don't seem to work on the KSC MP7 (CCW vs CW). Edited February 24, 2010 by 3vi1-D4n Quote Link to post Share on other sites
aznriptide859 Posted February 24, 2010 Report Share Posted February 24, 2010 I think both the TM and KWA threads are CW, but their pitches must be different. I got a prototype 12mm CW to 14mm CW adapter from -I- when I got my RF pack. I'll be testing it later. Also, here are some pics of the KWA short mag, if anyone's interested. Quote Link to post Share on other sites
-l- Posted February 24, 2010 Report Share Posted February 24, 2010 (edited) RF nozzle is not compatible with KSC "Taiwan" Version or any other version. It is only compatible with the "Japanese" version Actually, they have 2 version for both Japan and KWA/Taiwan. Japdn version have a green paking and Kwa ver. have a kahki packing. why are people cursing about not being able to replace the KWA nozzle with a readyfighter? It's only the KSC japan model that has the weak cylinder. "Two is one and one is none", it's always good to have a back up replacement parts, may be this is what the RF guys think. However I agree that KWA MP7 is actually a very good GBB out of the box. Edited February 24, 2010 by -l- Quote Link to post Share on other sites
greg Posted February 24, 2010 Report Share Posted February 24, 2010 The only Gas Mp7 that has reported broken nozzles is the KSC Jap. The nozzle on this one was made with a thinner side wall, is not compatible with the rest & blows after use with green. The Ready fighter nozzle is made to replace this nozzle only & due to the thinner walls, will not fit the others. The others have thicker side walls on the nozzle, with a smaller diameter cup & are not blowing. I am using Guarder HPM .28's. I am getting 12" groups at 50m. Hop adjusted correctly, a flat trajectory to about 60m. No misfeeds. I am currently using a 6.04x200mm tn barrel but was achieving similar accuracy & range with the stock barrel. Greg. Quote Link to post Share on other sites
-l- Posted February 24, 2010 Report Share Posted February 24, 2010 Anyone managed to get a silencer onto their MP7? Marui thread adaptors don't seem to work on the KSC MP7 (CCW vs CW). there you go, here is the production type RF silencer adapter, I know the silencer is not a 4.6mm type. Let's just all wait for dytac to make us a proper one. Quote Link to post Share on other sites
aznriptide859 Posted February 24, 2010 Report Share Posted February 24, 2010 ^Wow, I was actually really going for something close to that look... Guess I'm switching now LOL. Quote Link to post Share on other sites
jotohomomoto Posted February 24, 2010 Report Share Posted February 24, 2010 (edited) The real-steel MP7 has a proprietary suppressor. I was wondering if anybody knows any further information about it and possible airsoft replicas. also, whats a good sling for this gun? Edited February 24, 2010 by jotohomomoto Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.