wdahm519 Posted April 14, 2011 Report Share Posted April 14, 2011 (edited) Its finally time to sell my KJW M4 guys... you can check it out in the commerce. Edited April 14, 2011 by wdahm519 Quote Link to post Share on other sites
WTF?Shane Posted April 14, 2011 Report Share Posted April 14, 2011 Does RA-tech's barrel accept AEG hop-up rubbers? Â No, it uses the stock KJW M4 GBBR style. Quote Link to post Share on other sites
GI Tye Posted April 14, 2011 Report Share Posted April 14, 2011 Hey, i managed to cut a bycicle rubber tube with an x-acto to do a rubber seal that fitted in around the fill valve...and they work...and as T_hum says..i'm still waiting for a response from Clare about the upper receiver to get my rifle alive again. Â Â Do you have the email address?? Quote Link to post Share on other sites
slipknot1971 Posted April 14, 2011 Report Share Posted April 14, 2011 Do you have the email address??   Sure!...it's  kjworks@ms47.hinet.net 1 Quote Link to post Share on other sites
Darkstrike Posted April 14, 2011 Report Share Posted April 14, 2011 again another retard question but how do you take off the front sight post? im going to replace it with something cooler Quote Link to post Share on other sites
def3kt Posted April 14, 2011 Report Share Posted April 14, 2011 I don't mean to flame you.....but.....read/search this thread. Your question has been asked dozens of times. Â again another retard question but how do you take off the front sight post? im going to replace it with something cooler Quote Link to post Share on other sites
t_hum Posted April 14, 2011 Report Share Posted April 14, 2011 There are two pins on the underside of the sight post that key into the barrel. Knock them out with a pin punch and the post will slide right off. Quote Link to post Share on other sites
alex chang Posted April 15, 2011 Report Share Posted April 15, 2011 I didn't have time to fully test out the new falcon hop up, single nub. It worked a little better than the normal one. Both hop ups had shrink wrap mod (didn't change between the two, just swapped out bucking.) I wouldn't say its worth it to purchase it, just stick with the normal one. I haven't had a change to test the fps difference, but it does seem like there is a better seal. Â On another note i purchased a magpul BAD lever and it works flawless. I didn't have to do a single modification, took less than 30 seconds to install. After this weekend i'll chime in with more falcon hop up bucking feedback. Quote Link to post Share on other sites
Darkstrike Posted April 15, 2011 Report Share Posted April 15, 2011 There are two pins on the underside of the sight post that key into the barrel. Knock them out with a pin punch and the post will slide right off. Â thanks dude! Quote Link to post Share on other sites
theprodigy Posted April 17, 2011 Report Share Posted April 17, 2011 DOES ANYONE HAVE A LOADING NOZZLE THEY WANNA SELL ME???? PLEASEEEEE ITS DESPERATE...... KJW WILL NOT SELL TO ME..... Quote Link to post Share on other sites
slipknot1971 Posted April 17, 2011 Report Share Posted April 17, 2011 (edited) DOES ANYONE HAVE A LOADING NOZZLE THEY WANNA SELL ME???? PLEASEEEEE ITS DESPERATE...... KJW WILL NOT SELL TO ME..... Â Â Hey prod..maybe this can help you my friend...it's not a fast solution...but it's available... Â http://www.law-airsoft.com/en/main/produit/id_produit/30 Â Â And why aren't they selling to you??? Edited April 17, 2011 by slipknot1971 Quote Link to post Share on other sites
_Samuel_ Posted April 17, 2011 Report Share Posted April 17, 2011 (edited) Hello, I have a catastrophic failure in the internals of my KJW M4. The internals are totally jammed and I found metal and plastic shavings falling out of the gun. It is sad that I haven't even had this gun for a weak. Â Here are a few links for pictures of the internals. Â Links: http://img858.imageshack.us/i/dsc02029r.jpg/ http://img839.imageshack.us/i/dsc02023v.jpg/ http://img845.imageshack.us/i/dsc02024e.jpg/ http://img571.imageshack.us/i/dsc02025d.jpg/ http://img684.imageshack.us/i/dsc02026cu.jpg/ http://img816.imageshack.us/i/dsc02027j.jpg/ http://img810.imageshack.us/i/dsc02028q.jpg/ Â Do you guys have any idea what I could do to fix it or should I just return it to the retailer I bought it from for repair / replacement? Â Thanks. Edited April 17, 2011 by _Samuel_ Quote Link to post Share on other sites
Mister Miles Posted April 17, 2011 Report Share Posted April 17, 2011 You definitely want to contact the Retailer AND KJW. I have never seen anything like that before...not good at all. Quote Link to post Share on other sites
_Samuel_ Posted April 17, 2011 Report Share Posted April 17, 2011 I know it is horrible. I just got the gun and it was working so well. Should I call the U.S. number for customer support for KJW? Quote Link to post Share on other sites
_Samuel_ Posted April 17, 2011 Report Share Posted April 17, 2011 I know it is horrible. I just got the gun and it was working so well. Should I call the U.S. number for customer support for KJW? Â Also, I got a faulty magazine too that leaked propane inside my house. Â Finally, whenever I get my replacement I am going to make it into a DMR. I am trying to put it in a place where it doesn't get in the way of the charging handle though. Two pictures are in the links below. Â Links: http://img811.imageshack.us/i/dsc02030c.jpg/ http://img812.imageshack.us/i/dsc02032v.jpg/ Â Â Â Quote Link to post Share on other sites
GismoBE Posted April 17, 2011 Report Share Posted April 17, 2011 Is there allready a proven solution for the hop-up? Â Â Quote Link to post Share on other sites
_Samuel_ Posted April 17, 2011 Report Share Posted April 17, 2011 (edited) Nevermind I FIXED IT!!! I don't know how, but I just used an allen wrench and somehow unjammed it! Â I just need to send my black flashhider and faulty magazine back to airsplat. Now, I will make it into a DMR. Here is a few pictures of it. How could I get the scope out of the way of the charging handle while still being able to extend the stock all the way? Â Also, how would I get the scope mounts lined up right without them being angled? It works correctly on my UTG L96 and they are same rail system since they make it standard. Â Links: http://img811.imageshack.us/i/dsc02030c.jpg/ http://img812.imageshack.us/i/dsc02032v.jpg/ http://img194.imageshack.us/i/dsc02035w.jpg/ Â Â Edited April 17, 2011 by _Samuel_ Quote Link to post Share on other sites
Bleaumaglite Posted April 17, 2011 Report Share Posted April 17, 2011 Samuel, get a SPR or any sort of M16 length front end. Order a T-Hum M16 length tightbore and be sure to mod the M16 outer barrel correctly. A M4 + a scope does not make it a DMR. Especially seeing the KJW M4 inner barrel only goes until the front sight. Quote Link to post Share on other sites
t_hum Posted April 18, 2011 Report Share Posted April 18, 2011 Gismo, The TDC mod gives good results. If you want more details you can PM me. Quote Link to post Share on other sites
frogfish Posted April 18, 2011 Report Share Posted April 18, 2011 (edited) Stupid internet. Edited April 18, 2011 by frogfish Quote Link to post Share on other sites
frogfish Posted April 18, 2011 Report Share Posted April 18, 2011 Gismo I posted a write up on the TDC mod a few pages back. If my ISP wasn't ###### I could easily go back and link the posts for you, but alas I'm on a phone and to lazy to put in the effort right now. Quote Link to post Share on other sites
_Samuel_ Posted April 18, 2011 Report Share Posted April 18, 2011 (edited) Hello again t_hum. I am enjoying my KJW M4 now that it isn't broke. The only thing I found wrong with it was the picture below. The metal is somehow seperating from itself. Â Link: http://img855.imageshack.us/i/dsc02054u.jpg/ Â What is the TDC mod? Edited April 18, 2011 by _Samuel_ Quote Link to post Share on other sites
theprodigy Posted April 19, 2011 Report Share Posted April 19, 2011 Hey prod..maybe this can help you my friend...it's not a fast solution...but it's available... Â http://www.law-airsoft.com/en/main/produit/id_produit/30 Â Â And why aren't they selling to you??? oh i dunno there not responding to my emails anymore.. and ive bought a bunch of things in the past from them.. guessing cause im from america. Quote Link to post Share on other sites
theprodigy Posted April 19, 2011 Report Share Posted April 19, 2011 Stupid internet. lol Quote Link to post Share on other sites
theprodigy Posted April 19, 2011 Report Share Posted April 19, 2011 got the falcon rubbers in today can't test nothing yet, thum has my upper but when i get it back and take some shots in a controlled environment. Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.