Berggy Posted October 20, 2013 Report Share Posted October 20, 2013 Mods are juat m120 spring with the contact plates replaced with tamiya connector soldered. My scar H suffer less lock up without know why the mods are just the same Sent from my GT-I9300 using Tapatalk Quote Link to post Share on other sites
Richard Y Posted October 20, 2013 Report Share Posted October 20, 2013 You could try winding the stock tube out by one turn.. Too much spring compression can cuase lock ups on m4 next gens. Unfortunatly becuase the back of the gearbox is removable it also means it can be installed differently each time.. ie you could wind it in all the way, over time as threads wear and loosen up a little theres the chance of it winding in more, also no one really knows the exact postion it should be i think i had a new sopmod one time and on first taking apart i could actually wind it in a turn.. leading me to believe the natural position for the stock tube is not fully wound in, maybe they have a way to work it out during assembly to standarise manufature.. potentially winding it in too far could make the space for spring compression very tight and with an m120 this is amplified more over. Try winding it out a turn and see if you get a better ROF / trigger response before trying anything else. Quote Link to post Share on other sites
dragleefy Posted November 12, 2013 Report Share Posted November 12, 2013 Anyone know if you can remove the stock battery system and wire it for a deans battery? On another note, does anyone have experience with this?http://www.wgcshop.com/wgc2008/main/product_detail1.php?search_From=category&item=GMM-UBWK&search=special&rs=Conversion%20Kit%20for%20AEGs&catid=14&cat=318&view_choice=a Quote Link to post Share on other sites
dragleefy Posted November 12, 2013 Report Share Posted November 12, 2013 Nevermind.... Didnt read enough. fml Quote Link to post Share on other sites
Zereck Posted November 13, 2013 Report Share Posted November 13, 2013 At first I just welded a deans connector with a short cable to the original battery plug which worked fine, but after upgrading the insides I just removed the entire battery system(the plug, the rods, etc.) and just rewired it from the trigger to the stock. A deans connector fits just barely through the stock. Do you have some picture of your shrinktube fix?? Yeah we have also a 400fps full auto here but I am not sure if I take the gun apart. Actually as it turns out the shrinktube is not a correct fix as it makes the gun stop firing after one shot regardless of remaining bbs. However I can confirm that the other fix does work(where you put something between the receiver and the bolt catch mechanism where the latter is loosened thus it gets pushed back to its place) after I glued a small foam to the receiver where the bolt catch mechanism is. Quote Link to post Share on other sites
JCheeseright Posted November 18, 2013 Report Share Posted November 18, 2013 Anyone tried the recoil shock specific PTS PMAGs in the marui 416? I know in a real 416 the PMAG has issues but I'm not sure if that would translate into airsoft. If there are issues, has anyone tried fitting TM midcap internals into a real EMAG shell? Quote Link to post Share on other sites
PureSilver Posted November 18, 2013 Report Share Posted November 18, 2013 The PTS PMAGs work just fine; the Marui doesn't have the differing dimensions that cause the problems with the RS HK416 and some (early) PMAGs. Quote Link to post Share on other sites
JCheeseright Posted November 18, 2013 Report Share Posted November 18, 2013 excellent news, looks like fire-support (dunn dunn dunnnnnnnn) are going to be receiving some of my monies soon Quote Link to post Share on other sites
Honzo Posted December 7, 2013 Report Share Posted December 7, 2013 Tokyo marui hk416 DEVGRU coming out. Price is kinda high, huh? I know they lower the actual price on release but still.... http://www.tokyo-marui.co.jp/products/electric/nextgeneration/370 Quote Link to post Share on other sites
arne71 Posted December 7, 2013 Report Share Posted December 7, 2013 Yeah! That`s not even clever marketing. Calling it "Devgru custom" and including a different tfg and the wrong suppressor. But when have such minor details stopped the manufacturers from ripping off the customers? This is the free capitalist world after all. He.., even China has grasped that concept. Apart from the freedom part that is…. I love the fact that TM released the standard HK416, it`s a winner for sure. But they could have done so much better with the so called Devgru custom thing. Just relax. In about six months time we will likely see a significant price drop. Quote Link to post Share on other sites
druid799 Posted December 7, 2013 Report Share Posted December 7, 2013 Plus I'd say if your buying a TM 416 your not going to be new to the game (price to get one of these up and running) so I would have thought odds on you've already GOT everything you need to dress one up as a 'seal special' already ? I know I have ! Lol Quote Link to post Share on other sites
Forti Posted December 17, 2013 Report Share Posted December 17, 2013 Why would you replace the existing 416 irons with some terrible american peephole things? I don't get it. Quote Link to post Share on other sites
JCheeseright Posted December 17, 2013 Report Share Posted December 17, 2013 can't easily co-witness the H&K style iron sights with an aimpoint/eotech style sight. In airsoft of course that doesn't really matter, but for those who want the SF look changing the iron sights is a simple thing. Quote Link to post Share on other sites
arne71 Posted December 30, 2013 Report Share Posted December 30, 2013 Is it fair to assume that Marui has obtained a license from H&K? Or or is it more a case of the usual "we don`t care about copyright" stuff? Quote Link to post Share on other sites
PureSilver Posted December 30, 2013 Report Share Posted December 30, 2013 Without access to internal documents it's impossible to be sure, but knowing Japan's strict trademark and copyright regime, I'd say it was probable that Marui have a license which covers Japan only. Quote Link to post Share on other sites
point_7 Posted December 30, 2013 Report Share Posted December 30, 2013 i orderd a 416d from wgcshop, i hope it comes in this week , but i think not during these holidays. Quote Link to post Share on other sites
arne71 Posted December 31, 2013 Report Share Posted December 31, 2013 Without access to internal documents it's impossible to be sure, but knowing Japan's strict trademark and copyright regime, I'd say it was probable that Marui have a license which covers Japan only. Agree with you PS. Hopefully in the not too distant future we`ll be getting the 417 too. A blowback dmr with a Marui hop unit is very tempting. 1 Quote Link to post Share on other sites
Richard Y Posted January 2, 2014 Report Share Posted January 2, 2014 Is it fair to assume that Marui has obtained a license from H&K? Or or is it more a case of the usual "we don`t care about copyright" stuff? TMs all ligit, which was why the RECCE was originally delayed back in the day licensing issues so they couldnt release, ie madbull stepped in and said we want some pennies please, all of there stuff including the Daniel defense RIS is now all licenced.. albiet in japan... Which is why marui tends to stick to japan only. I would imagine it would cost alot to grease all the palms needed to be global. 1 Quote Link to post Share on other sites
christhesecond Posted January 2, 2014 Report Share Posted January 2, 2014 TM 417 set to 400 on semi would be epic! Quote Link to post Share on other sites
point_7 Posted January 2, 2014 Report Share Posted January 2, 2014 what kind of upgrades you guys sugest for my tm 416d ? i allready have a prommy barrel incomming . Quote Link to post Share on other sites
stewpidbear Posted January 2, 2014 Report Share Posted January 2, 2014 Really depends on your local limits. But personally none. Both Druid and I have not upgraded internals because out of the box ours were easily keeping up with so called tuned upgraded AEGs. Read the rest of this thread for views but really just change the battery connectors so you can use 7.4 lipos. Quote Link to post Share on other sites
christhesecond Posted January 2, 2014 Report Share Posted January 2, 2014 Definitely remove the stupidly high resistance *suitcase* in the stock. It's a fix for a non existent problem IMO. Personally I wouldn't touch the barrel or hop as I did and initially I thought it was better but now I've realised that was a bit of a placebo. I upgraded to an eagle6 m100 which it found does make a huge difference. The extra 45 fps makes a big difference. Quote Link to post Share on other sites
point_7 Posted January 2, 2014 Report Share Posted January 2, 2014 well i have a 350 fps limit, but i think the prommy barrel wil increasse the fps a bit ? but im having a marui spare hop unit comming my way to, so i put the prommy barrel in the second unit. but i have some 13;1 super shooter gears laying arround i whas planning to put em in there to or mayby not a good idea ? Quote Link to post Share on other sites
stewpidbear Posted January 2, 2014 Report Share Posted January 2, 2014 (edited) Really do not open the gearbox, if it ain't broke don't fix it! Edited January 2, 2014 by stewpidbear Quote Link to post Share on other sites
druid799 Posted January 2, 2014 Report Share Posted January 2, 2014 Really do not open the gearbox, if it ain't broke don't fix it!What he said , I've never ever felt 'out gunned' at any scurmish with mine left stock . Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.