Slayer750 Posted September 30, 2010 Report Share Posted September 30, 2010 (edited) Interesting. - Is the 553 a real 553 or a replica? I have a real 553 and I'll check it on my upper rail. - Definitely document the mold lines with pictures, etc. It's important to have that evidence available to further investigate it. If the factory casting or cleaning up the casts is dropping the ball, it's important for PTS to know this. - The plastics to me feel comparable to other Magpul PTS plastics. But that's my thoughts on it. YMMV - Interestingly, the real ACR has a little bit of flex to it too. I noticed this at SHOT Show this year. - Regarding the non-compatibility with old PMAGs, I'll have to test my own. I didn't recall there being an issue. So it would be interesting to investigate this some more and report back to PTS on this. - The motor being whiny, isn't that apparent to me. But it seems this is a YMMV. All in all, interesting observations. I'm certainly going to look into the production samples I have to make comparisons. The 553 is a replica. I should have specified that. However, I have no problems fitting it on anywhere I'd like on my G&P M4, KWA M4, KWA G36C, and G&P M14. The mold lines are very prominent. I'll take some pictures for documentation when I have a chance. I wish my PMAGs would fit. I'm not at all interested in buying another set up mags just so that I can field my Masada. One of the things that made me buy the Masada over some other AEGs I was considering was because I was counting on being able to use all the PMAGs and STANAGs I already have. The motor is very comparable to many others. Not terrible, but I felt that I should comment that it does indeed whine. Edited September 30, 2010 by Slayer750 Quote Link to post Share on other sites
Sacair Dagger Posted September 30, 2010 Report Share Posted September 30, 2010 I installed my RS LaRue absolute co witness T1 mount on the MagPul ACR and it fit perfectly. I would say the ACR top rail is very close to "mil-spec". That being said, if you own a "clone red dot" like Slayer750 553, with any type of throw lever mount, it may or may not fit properly. If needed you can always add some type of shimming material, (brass shim stock) works well between the rail and mount before locking it down. Quote Link to post Share on other sites
Slayer750 Posted September 30, 2010 Report Share Posted September 30, 2010 I installed my RS LaRue absolute co witness T1 mount on the MagPul ACR and it fit perfectly. I would say the ACR top rail is very close to "mil-spec". That being said, if you own a "clone red dot" like Slayer750 553, with any type of throw lever mount, it may or may not fit properly. If needed you can always add some type of shimming material, (brass shim stock) works well between the rail and mount before locking it down. It isn't wobble that I'm dealing with. The problem is that it can only clamp down to one spot on the rail, and when trying to mount it on any other part of the rail, one of the clamps will not cinch down. I realize that this problem likely has more to do with the replica of the 553 and not the Masada, but seeing how it fits with no problems on all of my other AEGs, it is quite aggravating that it doesn't fit onto the Masada. Quote Link to post Share on other sites
Ycare Posted September 30, 2010 Report Share Posted September 30, 2010 I totally[...] it will be addressed. Totally agree with you 200%. PTS was always very professional and did not tell me they would replace it at any point, it was eHobby Asia all along which said so while obviously speaking out of knowledge. And yeah... the box feels... "tired" after all those shipping, but the AEG is there, and that's all that matters! Quote Link to post Share on other sites
uscmCorps Posted September 30, 2010 Report Share Posted September 30, 2010 The 553 is a replica. I should have specified that. However, I have no problems fitting it on anywhere I'd like on my G&P M4, KWA M4, KWA G36C, and G&P M14. When I got home from the gym tonight, I looked all over my gear collection for my RS 553 only to finally discover that it was already installed on my ACR. I have no problems installing the 553 nor any of my other optic mounts on the ACR rails. I do recall that the ACR has an accurate Mil Spec 1913 rail, same as the real deal. I'd expect most replica mounts will probably work fine with the ACR. The replica 553s might be severely out of spec ... but the issue hasn't been as evident since most airsoft rails are a little loose and accommodating on tolerances. The 553 is tricky because it has two points of attachment, and the distances between those two points are fixed. If the distance isn't in spec on the 553, it won't work with the ACR. 1913 spec is pretty unforgiving like that. 1 Quote Link to post Share on other sites
anonimouse9 Posted September 30, 2010 Report Share Posted September 30, 2010 I got my Masada (SN-MPTS1159) in FDE today. I can't say I got quite what I was expecting. I have read that the Masada is one of the most comfortable and ergonomic AEGs out there, and that it is very nice to shoulder. I have also read that the Masada is one of the most real feeling AEGs out there. I'm not sure I agree with these two statements. The Problems -The top rail seems to be a bit strange, as I can only lock my 553 down in certain places. -There are mold lines everywhere, which kind of disturbs me. It honestly looks like an Echo 1 G36C or something. -The plastic does not seem to be of the same quality as other Magpul items. -The barrel and handguard both wobble a bit, which has an end result of making the barrel seem like it wobbles a lot. -The Masada, as others have reported, does NOT take old version PMAGs. They won't fit into the magwell. G&P M4 midcaps seem to seat fine, though. -The motor is a bit whiny, not too bad though. Enjoyable Aspects -The pistol grip is quite nice, and the position of the fire selector, bolt release, and mag release are nice as well. -The firing sound is nice despite the motor whine, giving a cool -CLANK- noise with each shot. As you can seem, I am not 100% pleased with my purchasing. In the beginning I was expecting a LOT. In the past few weeks, my expectations plummeted due to reports on this forum and others. When I opened the box up, my expectations were relatively low, however I was still a bit disappointed. For $450 plus $75 shipping, one would assume they are buying a very high quality AEG. I don't believe that I have received that... I got to wonder about quality of molds between colors. I have a black Masada, and after seeing complaints about mold seams I told a good look at mine. All of my seams are extremely clean, and smooth. Honestly, aside from the fact I think the front site is cheesy (I'd would have preffered another MBUS for the front) I have zero complaints. The gun is ligtht, ergonomic, comfortable, and the plastic seems to be the toughest plastic I've seen on any gun. As for the cost, yest I expected a little more bang for the buck... but $75 for shipping? Why not buy it from a US store? Granted I paid $480 from ASGI, but with their shipping it was still less than those of you buying it from HK shops. Quote Link to post Share on other sites
jgarnreiter Posted September 30, 2010 Report Share Posted September 30, 2010 I didn't know the old PMag's weren't working for people. I skirmished mine the other day and my old PMag's worked beautifully. They actually work/fit even better than the newer PMag that came with my ACR. The fit is rock solid and I haven't had a single hiccup when it comes to feeding. That's really strange. Quote Link to post Share on other sites
Megalomaniac Posted September 30, 2010 Report Share Posted September 30, 2010 My dissapointment stems from PTS' lackluster warranty support and from Spartan Imports ever changing story about how and when my gun will be fixed. As of last night the parts MIGHT be 6 weeks away, but they cannot confirm wether the parts are in that shipment, and so far are resistant to the idea of swapping the gun out for me with a working one. Quote Link to post Share on other sites
Doedkoett Posted September 30, 2010 Report Share Posted September 30, 2010 Mine also has visible, but trimmed down mold lines, but I haven´t really reflected about it since my limited experience with real "modern" military firearms is suggesting that they are produced to pretty much the same aestetic standards, which is "good enough and as cheap as possible". Older weapons, like a FN MAG from 1958, which is made from steel and wood are often built to completely different standards. At least compared to a 1980's FN FNC, made from molded ABS-plastic, aluminium and spot welded steel made in a fully automated production line. Quote Link to post Share on other sites
Megalomaniac Posted September 30, 2010 Report Share Posted September 30, 2010 To those that have tinkered with the gearbox on the MASADA is the cutoff lever a standard design? And when fitting the box into the lower did you need to depress the trigger any? Quote Link to post Share on other sites
sacairsoftsn00py Posted September 30, 2010 Report Share Posted September 30, 2010 No. Yes. 1 Quote Link to post Share on other sites
Apocalypsemeow Posted October 1, 2010 Report Share Posted October 1, 2010 Gah another two weeks until Dingodogs get their pre-orders in 1 Quote Link to post Share on other sites
hwagan Posted October 1, 2010 Report Share Posted October 1, 2010 LandWarrior have them in stock and ready to go Quote Link to post Share on other sites
Slayer750 Posted October 1, 2010 Report Share Posted October 1, 2010 I got to wonder about quality of molds between colors. I have a black Masada, and after seeing complaints about mold seams I told a good look at mine. All of my seams are extremely clean, and smooth. Honestly, aside from the fact I think the front site is cheesy (I'd would have preffered another MBUS for the front) I have zero complaints. The gun is ligtht, ergonomic, comfortable, and the plastic seems to be the toughest plastic I've seen on any gun. As for the cost, yest I expected a little more bang for the buck... but $75 for shipping? Why not buy it from a US store? Granted I paid $480 from ASGI, but with their shipping it was still less than those of you buying it from HK shops. The was in quite a bad mood the day I received my Masada. Inspecting the seam lines again today, they don't seem nearly as bad. As for the cost bit: $450 (for Masada) + $74 shipping (express; got it one day after it shipped out) - $22.50 (5% eHobby discount) = $501.50 plus I got a free FDE MVG that I would have bought anyways. If I had bought it from Airsoft GI or Evike, I would have to pay another 10% for tax since I live in California, which pretty much equals things out. The main reason that I bought it from eHobby, however, is because I'm not a fan of Evike's or ASGI's online services. It is very slow and people seem to be *fruitcage*ed over a lot by both companies when purchasing online. Quote Link to post Share on other sites
SixtyNiner Posted October 1, 2010 Report Share Posted October 1, 2010 Gah another two weeks until Dingodogs get their pre-orders in Airsoft Armoury also has them. Maybe stock is arriving earlier than expected. Quote Link to post Share on other sites
Apocalypsemeow Posted October 1, 2010 Report Share Posted October 1, 2010 LandWarrior have them in stock and ready to go I know, it's damn tempting to take a trip there tomorrow and I'll be playing there on Sunday anyways, was going to try hold out for an FG one from Dingodogs though but the suspense is killing me lol Quote Link to post Share on other sites
Leapfrog Posted October 1, 2010 Report Share Posted October 1, 2010 (edited) Airsoft Armoury also has them. Maybe stock is arriving earlier than expected. They are £20 cheaper at Airsoft Armoury as well, I'm waiting for mine to be delivered today. Edited October 1, 2010 by Leapfrog Quote Link to post Share on other sites
Tacitus Posted October 1, 2010 Report Share Posted October 1, 2010 (edited) I emailed Airsoft Armoury asking if the Masadas they have in stock are the UK version, this is the response I got: "Hi, Magpul have no knowledge of a UK Spec version. We are assuming the UK distributor (Edgar Bros) is changing the wiring due to RoSH compliancy and stamping the 30 day warranty card with their details. We are supply a 12 month warranty ourselves (will still have a 30 day warranty with Magpul), ours have no RoSH compliancy issues and ours dont need a spring change as they are already doing 330-340 fps out of the box. Kind regards, A2" Can someone clarify exactly what the 'UK spec' Masada is exactly? There already seem to be 2 different versions (1 with 'Made in Hong Kong' engraved on the side, 1 without). We have also been told that the UK version will have some sort of holographic sticker, and shoot 328fps. Edited October 1, 2010 by Tacitus 1 Quote Link to post Share on other sites
kithooton Posted October 1, 2010 Report Share Posted October 1, 2010 Fire Support are Pre-Ordering Masada's http://www.fire-support.co.uk/product/magpul-pts-masada-acr-dark-earth---pre-order-coming-soon Unsure if they are UK Versions. I've bought the Folding Stock from them £70 Just Can't wait for 10 inch and the RIS Hand Guard, Then i'm Done being Poor Quote Link to post Share on other sites
kithooton Posted October 1, 2010 Report Share Posted October 1, 2010 http://www.ginganinga.com/MMAR/ Register your Masada Quote Link to post Share on other sites
Scuffer Posted October 1, 2010 Author Report Share Posted October 1, 2010 Right I will 100% clear something up for all UK users:- # NONE of the UK spec Masadas are in the coutry yet, they will be roughly 2 weeks. # The UK spec model is being made by Magpul PTS in HK, then imported via Edgar Bros. Edgar Bros are not fitting the wiring themselves as stated by Airsoft Armoury. Airsoft Armoury stating that Magpul have no knowledge of the UK spec models is either very reveling about how little they know, or they are try to ###### you due to them stocking grey imports. # The UK spec model differs on: External and internal paint/finish, wiring, spring and I believe warranty (as in theirs is the only one actually supported by PTS) - this is due to typical UK power limits and RoHS import compliance. The US/HK spec models are not RoHS compliant. 1 Quote Link to post Share on other sites
Disajim Posted October 1, 2010 Report Share Posted October 1, 2010 My Masada arrived 2 days ago from Redwolf Airsoft. Black, S/N 02517 1 washer (C22). In this link you can find pics of my gun (around 90) with many close ups. http://img194.imageshack.us/g/img9828wp.jpg/ 1 Quote Link to post Share on other sites
DECURION Posted October 2, 2010 Report Share Posted October 2, 2010 I would appreciate if someone could help me.. Have anybody had any problem with handguard pins? After opening the handguard just about ten times the pin has became loose and is falling off from the AEG... Any ideas where can I buy a new pin please? ACR is too pretty to have black tape on it! Quote Link to post Share on other sites
JBS Posted October 2, 2010 Report Share Posted October 2, 2010 My Masada arrived 2 days ago from Redwolf Airsoft. Black, S/N 02517 1 washer (C22). In this link you can find pics of my gun (around 90) with many close ups. http://img194.imageshack.us/g/img9828wp.jpg/ Great pics! My front hand guard looks exactly like yours with the obvious mold marks. Quote Link to post Share on other sites
JBS Posted October 2, 2010 Report Share Posted October 2, 2010 I would appreciate if someone could help me.. Have anybody had any problem with handguard pins? After opening the handguard just about ten times the pin has became loose and is falling off from the AEG... Any ideas where can I buy a new pin please? ACR is too pretty to have black tape on it! Have you lost the retaining clip on the inside of the hand guard? The clip doesn't look anything unique and may be purchased at you local hardware store. Quote Link to post Share on other sites
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.