Jump to content
krame

Glock Picture Thread

Recommended Posts

Here's some pictures of one of the custom projects that I finished not too long ago.

 

For a long time I have been talking about installing a clipdraw on my TM G26 but I have finally actually done it. I believe that this is the only TM Glock that I have seen with a ClipDraw.

 

It was a bit of a pain but it works nicely and is a very solid fit (even thought it is just a touch higher than it should be).

 

clip3wd6.jpg

 

clip1ub8.jpg

 

clip2tv5.jpg

 

clip4tz3.jpg

 

Bits:

 

TM Glock 26

 

Guarder Steel Slide

Guarder Steel Outer Barrel (Bead Blasted)

Guarder Recoil Springs

 

PDI Piston Head

 

SD 'Glock" Magazine Base Plate

 

RS ClipDraw

RCW ClipDraw Screws

 

Nine Ball 6.03mm Tight Bore

Nine Ball Air Seal

 

KM TN Hi Flow Valve

 

FireFly Recoil Guide Rod w/ Bearings

Share this post


Link to post
Share on other sites

Nice one QDRenegade. Thanks for sharing that info. So the front sight is held in with a screw? Does it not catch and scrape the outer barrel? What glue did you use for the rear sight, is it held firmly in place now? They look really good mate.

 

Wayneard, how did your XS Big Dot sights fit? They're definitely very unique, I like 'em!

 

Talking about used Glocks, I thought you guys might appreciate this;

 

Glock 21 Torture Test

 

It's quite a long article but definitely worth reading and there is some great pics in there too!

 

Romulus, glad to see you got your Clipdraw installed mate. Did you drill into the rear plate cover then? With mine the middle tab on the Clipdraw rear plate cover was catching on the frame internals so needed a bit of material removed. But obviously you wouldn't have had that problem as you didn't use the Clipdraw cover (mine is installed on a KSC Glock 17, I think we talked about it a while back?)

 

 

Share this post


Link to post
Share on other sites

I did drill and tap the back plate of my stock BBU. However, I ended up also having to remove more material from the rear site well so that I could get my tap all the way though. I was concerned that with the quality of the TM metal I would risk pulling my screws back out.

 

Luckily it seems that I got it deep enough that it is solid and didn't more at all during my testing.

 

It is really quite fun.

Share this post


Link to post
Share on other sites

Nice G26's!

 

Spartan-

I returned your PM about the fitting issue. I was having the exact same problems with the SD G26 slide. Monster pain in the *albatross*

Edited by junior

Share this post


Link to post
Share on other sites

Here are some crappy pictures...

Man! I really need to ditch my crappy camera on my phone and get a digital camera!

Note: Everything has a white (almost foggy looking) look because the lens over my camera phone is really scratched.

 

0120091747fj3.jpg

 

0120091748qz4.jpg

 

0120091752jt5.jpg

 

0120091750tr1.jpg

 

Parts:

Aluminum CNC Shuey Custom slide

As far as i know, internals are stock, with one exception

Guarder recoil spring

Shooter's design magwell

If i can, I'll try to install the Guarder 150% hammer spring, but i can't get a screw out...

 

Is it possible to fit Meprolight sights onto a Tokyo Marui G17 with little to no modifications? Or would it be better to use Trijicons? (by better, i mean easier to install)

Share this post


Link to post
Share on other sites

@stealth 1911 how did you get your slide so shiny and wouldn't that be a problem it relefcting the sunlight so the other players see it.

 

I need to buy more glocks i've only had about 5.

 

@ Romulus was it hard to fit the clip and doesnt it touch the slide cause it really sucks if you have scratches only there.

Share this post


Link to post
Share on other sites
@stealth 1911 how did you get your slide so shiny and wouldn't that be a problem it relefcting the sunlight so the other players see it.

 

I need to buy more glocks i've only had about 5.

 

@ Romulus was it hard to fit the clip and doesnt it touch the slide cause it really sucks if you have scratches only there.

 

It took me about an hour mainly because I didn't have all my usual tools (visiting the parents for Christmas). It wasn't super hard but it wasn't that easier either.

 

I don't think that I'll have problems with scratches since the clip is rock solid. If it got loose and could move up and down it could be a problem but in it's current state it won't move so I'm safe.

Share this post


Link to post
Share on other sites

I would doubt it since the rear site of the TM 17 doesn't look anything like an RS Glock site. In the TM 17 the site is a much larger piece that goes down into the slide/BBU. KSC's seem to be pretty close to RS though.

Share this post


Link to post
Share on other sites

@1st: Is that an Asian flashlight? If so, how well does it perform? Ive got a buddy who is interested in a flashlight but doesn't want to shell out more than the GBB itself (reasonably so).

 

@everyone else: Take more photos folks!!!

 

dsc0137nv0.jpg

 

G19 w/ GTL21 and Trijicon Night Sights.

 

Cheers.

Share this post


Link to post
Share on other sites

Just a quick pic of my KWA G19 and KSC G17 :) nothing speacial pic wise but both are really nice to shoot.

 

G19 has a harder recoil spring and is very used and abused as you can see from the wear marks from my Serpa holster, the G17 is standard now as the metal slide i had on it cracked so back to the original now <_< and its abit tight in the Serpa with the standard slide.

 

Glocks001.jpg

 

Hope you like :)

 

*AL* aka Lofty

Share this post


Link to post
Share on other sites

Figured you guys would know, I've got gas leaks in the magazines.

 

I take it your guyses advice would be replace the oring with one from a lighter?

 

 

just so its not fully spam. I'll repost with an old pic thats been posted long ago.

 

 

P6220062.jpg

Share this post


Link to post
Share on other sites
Figured you guys would know, I've got gas leaks in the magazines.

 

I take it your guyses advice would be replace the oring with one from a lighter?

 

 

just so its not fully spam. I'll repost with an old pic thats been posted long ago.

 

 

P6220062.jpg

 

gasket sealer around the orings is a one step solution. been working for over 6 years for me on any gun that comes through my shop.

Share this post


Link to post
Share on other sites

So I've always loved glocks sleek shape and design, now I want to get one for myself. Plus the fact that I have been playing a few mat hes of Metal Gear Online with pistols only. G18c rules!

 

I've been looking at the G18c and G23f both of which are full auto capable which should fulfill my lust for a machine pistol. I'm here asking what model(and manufacturer) are the "best"

I've heard that the 50 round mags are universal if I were to go down the KSC route and both pistols are the same price (again with the KSC versions)

 

I'm looking for reliability more than anything else. Thats the most important thing

 

So..

 

Wot am bestest gun?

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×

Important Information

By using this site, you agree to our Terms of Use and the use of session cookies.